Haas has turned out to be a company that has done more for the American Machinist than any other... the Toutube videos no small part of that feat... You have made a fan of me... thank you Haas.
@ludacrips76
Жыл бұрын
"we have hammered these mills mercilessly" ....good to see I'm no the only one that works a Haas like a sock puppet..lol
@zyndapp800
Жыл бұрын
We've been broaching with our old Haas 50-taper mill for years. Producing internal splines every day. Most important is to have probes on the machine, then all extras are working that is needed - M19, G68 and so on. It's not that difficult to write a single spline subprogram using G91 for stepover and then later G68 rotation for next spline and repeat. But very good video Haas, thanks!
@YCM30cnc
Жыл бұрын
😎😎👍👍…. I’ve never regretted buying my Garage machine from you folks, stuff like this makes it even more valuable. ⭐️⭐️⭐️⭐️⭐️ to HAAS and the folks working there that make building a profitable Side Hustle very possible.
@SuperstarComponentsLTD
Жыл бұрын
Thru coolant broaches give about 20 time tool life in our experience. We were broaching ratchets by moving the broach off centre line. 45 teeth with 6 passes on each in en8. Ran thousands of those a week
@capnthepeafarmer
Жыл бұрын
I knew you could do broaching on the Haas by making your own custom macro, I never knew it was a canned cycle already. let alone Haas having broaching tools. CNC broaching tools seem to be so uncommon, it's good to know Haas carries them.
@scottbrooks6571
Жыл бұрын
Been broaching like this in a Haas machine for a long time. You can also achieve a program like this with macros, which keeps the program nice and small.
@JaakkoF
Жыл бұрын
If memory serves correctly, broaching a 20 mm keyway is about equivalent in forces to drilling a 14 mm hole. Good indication that this is not harming the machine in any way compared to 'normal' use.
@John-ik2eg
Жыл бұрын
Forces spread across 360 degrees of bearing rotation in the drilling cycle. Full load on 1 degree in the broaching.
@Sketch1994
Жыл бұрын
@@John-ik2eg So all 5 axis trunions are just falling apart from working at 0° degrees? Bearings can take huge loads even statically before taking any permanent deformation. If the load was enough to brinnel a ring statically it would instantly wear a groove on the rings of thr bearings as soon as the load was applied when spinning, and drill thrust for example is seriously underestimated
@John-ik2eg
Жыл бұрын
@@Sketch1994 *Interesting*
@islandtechent
7 ай бұрын
The difference it when drilling the spindle is turning and not stationary. I wiped out my spindle bearings doing this
@jonathongonzalez914
10 ай бұрын
It would be nice to add in a widening option to be able to cut slightly wider keyways.
@theorangebaron1595
Жыл бұрын
Great guide video. Always informative!
@ytfan3815
Жыл бұрын
I would recommend Haas to re-write the cycle on the retract of the tool, go out of the material when you retract for a better wear on the insert. When you have to do lots of these operations it's way better for tool-live. 🤔😉
@joesmith2465
Жыл бұрын
hope ya make a spline video when they are available been looking for broaching toolholders
@davidfarmer
Жыл бұрын
lovely, would love to see spline broaches for involute 45 degree fine toyota splines.
@mcoregaming1199
Жыл бұрын
Please make video on knurling
@togd4u145
Жыл бұрын
I use our software at work for this, but I add a G187 P1 E.05 line. Takes off up to 30% of the cycle time. Does the vps incorporate something like this?
@lvxleather
8 ай бұрын
Good info, thank you 👍
@toytimeyota
6 ай бұрын
Please add external Broaching to the mill template! I was excited to see broaching added to VPS until I realized it was internal only.
@johnl5177
Жыл бұрын
could you add two features to one being the ability to shift the key to the side to allow larger keys to be made for example 3/8 broach taking 2 passes side by side = 3/4 with our building to much pressure. Another is could you please order the shanks in inch as well as metric. Like for 1inch& 1.5inch holders
@antshark
Жыл бұрын
Are the vps templates already installed in the machine? If so, where do you find them? If not, how does one obtain them?
@kasbien4485
4 ай бұрын
@haasautomation is it possible to cut an internal keyway that is wider than the width of the insert using the G156 canned cycle? Looking to cut 0.750"-1.500" wide internal keyways if possible.
@xCaptainKlutch97
Жыл бұрын
Is the broaching template for the lathes a free upgrade or does it cost money?
@haasautomation
Жыл бұрын
CaptainKlutch, Both the lathe and mill broaching templates are free upgrades. Just go to the download links on the Broaching page linked here www.haascnc.com/haas-tooling/broaching.html . . . there is also a link to instructions on the same page for installing the templates on your control.
@pco1984
Жыл бұрын
Can it make tapered keyways too (or would I need to tilt the part)?
@AlitaGunm99
Жыл бұрын
Can the ISO-20 taper CM-1 do broaching in aluminum, with small stepovers?
@starsun_lifestyle
Жыл бұрын
thank you 👏👏👏👏
@markushauser1764
Жыл бұрын
I have a Haas VF 2 SS EU 2018 , is this a Option for this machine ?
@islandtechent
7 ай бұрын
Isn’t it risky putting a load on the spindle bearing when they aren’t turning. I tried this and it wiped out my spindle bearings
@billknighton4181
Жыл бұрын
Late 2019 dm-2 with vps, macro, spindle orientation. What do I need to do to add this cycle?
@haasautomation
Жыл бұрын
Bill Knighton, The VPS Broach Template files for both Mills and Lathes are on this page (also linked in the description). There are also instructions for installing the template files on your control. www.haascnc.com/haas-tooling/broaching/broaching_toolholder.html
@MachinistNumbr7
Жыл бұрын
I see an awful lot of cycles on this guy's VPS that is not on mine....anyway to update the control/download those newer VPS cycles?
@haasautomation
Жыл бұрын
csprinkler, If you go to this "Broaching" page (www.haascnc.com/haas-tooling/broaching/broaching_toolholder.html?op=/haas-tooling.html&oh=broaching) and click on the Haas Broaching Line dropdown menu you will find links to the various broaching templates and installation instructions. Here is the link to the installation instructions. www.haascnc.com/reference-container/haas-tooling-references/vps-template-installation.html
@MachinistNumbr7
Жыл бұрын
@@haasautomation Super, thanks! I'll give that a try.
@brendonamos1669
Ай бұрын
Broaching uses a broach and way more efficient. This is slotting. Not broaching. And for a precision machine would be a good way to ensure HASS maintenance sells more spare parts as it would be damaging to the machine in the long run.
@rayhjr72
Жыл бұрын
no big deal I been broaching all 4 square corners in wave guides on my cnc's for years.
@ianlockwood7842
Жыл бұрын
can you use a g156 cycle on a super mini mill?
@gthtransmission2934
Жыл бұрын
Hello, Its possible for an VF2 YT EU ? i Dont have the VPS choice for broaching ! Thank You from France !!!
@haasautomation
Жыл бұрын
Hello GTH Transmission, The VPS Broach Template files for both Mills and Lathes are on this page (also linked in the description). There are also instructions for installing the template files on your control. www.haascnc.com/haas-tooling/broaching.html. These templates are available on both the EU and US version websites. Thanks.
@gthtransmission2934
Жыл бұрын
@@haasautomation All is perfekt Thank You
@user-bx3gu3st9b
Жыл бұрын
Isn't that how you put flat spots on bearings?
@haasautomation
Жыл бұрын
k, listen to what Bhop has to say at this point in the video about our experience using this type of broaching on our own machines here at the factory. kzitem.info/news/bejne/y6lpsKxpf5lzqoo
@williamhuang5329
Жыл бұрын
Hanzhen harmonic drive gear , strain wave gear reducer, robot joint , over 30 years experience
@adammiller4879
Жыл бұрын
Only thing I disagree with, You shouldn’t have to pay for add ons, it should come with every canned cycle and g code, it’s bull sht
@cyber2526
Жыл бұрын
I agree other brands all have this built in
@halomaster985
Жыл бұрын
Haas machines are cheap, kind of accurate, work horses. I'm not saying Haas makes a bad product. I do have to agree with you in this instance. There is absolutely no reason to need the rotational offsets feature when you can just as easily change spindle orientation instead.
@gordonburnett9672
Жыл бұрын
The way the macro is written requires increment in x, just easier to rotate by g68 especially when doing wide keys requiring a y offset, just gets messy in code otherwise. You could go buy an okuma or mazak or fanuc instead, and still have to pay their prices for the options, many of which are a hangover from the patents and copyright that GE put on these functions from the 60- 80s.
@adammiller4879
Жыл бұрын
@@halomaster985 eh, relatively cheap not super cheap, they are mid to low tier on rigidity and accuracy. My base model eco turn 450 dmg mori will repeat size and location less than 2 micron, yet the comparable haas lathe will vary about .0015 per part sometimes😂 it’s sad. The only thing absolutely amazing about haas is the user friendly controller with all the extra features, and the tech support is top of the line
@halomaster985
Жыл бұрын
@@adammiller4879 Tech support has been pretty lackluster in my experience. Repairs are a complete joke, but that's more due to Sellway having a monopoly on Haas service.
@davidkrimm9273
Жыл бұрын
Technically, this is SHAPING, not BROACHING! A shaper has a single cutting tooth. A broach has multiple cutting teeth.
Пікірлер: 54