I use a post level to set my drone on for calibration. Generally they’re taller than 6 inches which allows for the cord to point down. I also get a physical indication, in the level, that the craft is actually on a flat surface.
@godangle
20 күн бұрын
You gotta be careful with lactate, it is plastics. When you say "Loctite all screws", someone might accidentally Loctite the canopy screws. The best practice is to check for loose screws periodically especially after big crashes.
@Braincho
22 күн бұрын
Nice vid bro. 4:45 - you can fit BT2.0 plug into A30 - it goes in smooth so no need to solder/resolder.
@CG-RC
22 күн бұрын
Thanks for the info!
@nyclassic4ever130
10 күн бұрын
Thats the Eco
@iRazvan2745
22 күн бұрын
i was so focused on your video that i was filling my cup on the side it spilled everywhere 😂
@CG-RC
22 күн бұрын
😅
@godangle
20 күн бұрын
I know it seems counterintuitive, but if you turn down your VTX power indoors, you can actually improve your signal because reflected signals can cause interference, especially a higher power levels.
@XxKiloxX406
22 күн бұрын
Im new to ELRS and this is exactly what I needed to see to get mine setup! thank you!
@CG-RC
22 күн бұрын
Glad it was helpful!
@shogunemperor
22 күн бұрын
Daaaamn bro! Awesome video!! Love how detailed you are!!!
@darwin_win
17 күн бұрын
Hi, God damn, I love your post! It was awosome. New Mobula6 looked damn good! By the way, your recorded video was pretty good without much noise or break up with analogue. Can you tell me what goggles and reciever are you using? I am using skyzone o4o pro and stock reciver for my mini whoops but there is much noise and break-up. Thank you bro!
@CG-RC
12 күн бұрын
I am using the HD Zero headset with the TBS Fusion analog video receiver module. Its a good combo!
@BergeronFPV
23 күн бұрын
Never locktight a motor screw, Just buy spare screws. I lose mine alot, you can buy like 1000 pieces of them for about $5, When you land nice and flat you can hear the metal screws click, there taking alot of the impact. M1.4 x 4mm works, you can spend more money for titanium to save on weight. Make sure they aren't countersunk tho. Countersunk screws would start the 4mm measurement from the top of the head. I made that mistake recently.
@smika710
23 күн бұрын
RIP 3/4 motors of my first build. Screws ripped off locktite to the motor
@CG-RC
23 күн бұрын
Good info. I haven't had an issue with lock tight on my drones before. But better safe than sorry. Thanks for the advice.
@smika710
23 күн бұрын
@@CG-RC if you have dexterous hands & allocate the correct amount it bet it works.
@Hellfire_FPV
23 күн бұрын
very cool
@brandon9689
22 күн бұрын
My analog 2024 mob 6 lost video feed in 2 packs. By far the worst experience I've had in FPV so far.
@o-rex3898
13 күн бұрын
Find a way to fix it?
@BergeronFPV
23 күн бұрын
you dont need to change that plug it holds bt2.0 in tight. you want it.
@CG-RC
23 күн бұрын
Cool, I didn't know that. I guess I should have tried it first. lol. Thanks for the feed back!
@smika710
23 күн бұрын
May as well not add music
@CG-RC
23 күн бұрын
I am curious, why do you say that? Also, which section? Just trying to figure out how to make better videos. Thank!
@smika710
23 күн бұрын
@@CG-RC 16:20 is rough. Sounds like white noise over a drum beat with a drunk person screaming xD
Пікірлер: 27