WOW! What a great technician, he did the print head R&R with one hand. Wonderful.
@TRepair
Жыл бұрын
Thank you
@josealfredorosalescervante5931
18 күн бұрын
Excelente video, suscrito
@gabrielpaesbernardinelli3071
Жыл бұрын
A question please, it´s necessary caliber the print head after the change?
@craig156
3 ай бұрын
I have a mfc 3530dw and looks different then this when you first start to take of the cover to expose the wiring , could it be yours says Japan and mine says Business Smart Plus Series? Are they different?
@TheCalvin2271
Жыл бұрын
Hi, the yellow oren sticker on surface printhead nozzles need to remove or not?
@ChokriSalem
5 ай бұрын
Please give me a link or where did you get the refillable cartridges
@hoseakingguinto3539
Жыл бұрын
Question. I'm printing high quality photos however there's a lot of vertical linings. Is it printer head? Thanks for the response.
@riskinhos
Жыл бұрын
yes. try to clean it first before replacement
@svenkrause
Жыл бұрын
Dear T Repair Tech, Since you appear to be familiar with this Brother printer family: I have the slightly bigger model MFC J5730DW and the following problem; The MP multipurpose paper feeder on the back doesn't work anymore and I suspect that the drive shaft or a little gear of the feeding mechanism has come loose. In order to check and possibly fix this, it appears that I first need to remove the MP paper support assembly on the back to be able to access the drive shaft/gear mechanism. According to the Brother service manual (page 157), step 2 of the paper support assembly removal procedure says: "[step] (2) Release the two Hooks and remove the Paper support ASSY from the Main body". Unfortunately the schematic drawings is not really clear as how this releasing of the hooks works, and I'm afraid I will break something if I use force.....Do you by any chance know how to UNHOOK the da** MP support assembly? Your help - or that of somebody else reading this - is greatly appreciated. Regards, Sven. P.S. I can sent photos and/or copies of the manual if necessary
@younesshouhou9797
Жыл бұрын
من اي موقع قمت بشرئها وهل هيا جيدة
@maredknife5029
5 ай бұрын
Good video. Can u tell me where the waste ink cartridge is located?
@luanphamphuoc8092
9 ай бұрын
Bán hây quá bạn hướng vẩn tôi sửa khay MP bị kẹt không ép vào được
@jgchanneltv8648
Жыл бұрын
May i ask what causes the print unable 48? Is ot a printhead issue?
@TRepair
Жыл бұрын
you need replace new printhead
@BornAgainCynic0086
3 ай бұрын
@@TRepair No, the orange data cable on the head has not been firmly snapped into place, the2 liitle black snap locks.
@HaxLi
Жыл бұрын
And where can you buy print head? ;]
@robotmr8072
3 ай бұрын
thanks
@BornAgainCynic0086
3 ай бұрын
****** VERY IMPORTANT********Make sure the prinhead slides left to right BEFORE starting ANY OF THIS! You do this by doing a printhead clean with the cover open (put a screwdriver on the switch to bypass the open cover warning) and watch the printhead, when it moves to the left, pull out the power. And he has left out how to remove the ADF top cover from the body of the printer.
@godsinbox
7 ай бұрын
if you put it on 2x playback speed, it looks like he is frantically breaking in to steal it's arc reactor before the planet explodes.
@user-ei3uf5yl3e
4 күн бұрын
why in a rush?
@KSTR32
8 ай бұрын
Where can you buy this printer head and how much does it cost?
@christophecretin5981
Жыл бұрын
Hi i dont understand about the printer head . I can not make move the printer head for to acces for clean . Someone can help me about that ?
@jakubstarczynowski2698
3 ай бұрын
Hello sir, did you find fix of this? @christophecretin5981
@wudu6767
3 ай бұрын
@christophecretin5981 did you find to fix this problem? Same problem here
@BornAgainCynic0086
3 ай бұрын
@@wudu6767 The technicina forgot this step: Make sure the prinhead slides left to right BEFORE starting this! I'm stuck too!
@BornAgainCynic0086
3 ай бұрын
Partially rebuild the printer and... **** VERY IMPORTANT********Make sure the prinhead slides left to right BEFORE starting ANY OF THIS! You do this by doing a printhead clean with the cover open (put a screwdriver on the switch to bypass the open cover warning) and watch the printhead, when it moves to the left, pull out the power. And he has left out how to remove the ADF top cover from the body of the printer.
@bkp
2 жыл бұрын
@Steven_95_
Жыл бұрын
Bonjour vous savez réparé imprimante J'ai la même impriment MFC -J5335DW IL IMPRIME PLUS . JAI DÉMONTÉ MAIS POUR REMONTER C'EST ÉTAIT DUR. ET EN PLUSE ÇA ALLUME PLUS
@djamelyounes3243
Жыл бұрын
esque nous peut change le type de cartuche est devenire rechargable
@wudu6767
3 ай бұрын
Is there any way to contact with you?
@OsamaMohamed-mz8hv
Жыл бұрын
مكان حضرتك وسعر الهد بروزر ٢٣٣٠
@ahmednoweir6631
Жыл бұрын
لقيت مكان بيبيعها في مصر ؟
@REDDESIGN-msila
Жыл бұрын
خصني فيشور ليها
@mohdalimanroslan9910
10 ай бұрын
This dumb technician decide to skip the step where he lift the scanner at 3:12. There is one hinge he forgot to show so he decide to cut it. Whats the point of dissamble so fast but doesn't cover all step?
@BornAgainCynic0086
3 ай бұрын
Yes, I am now stuck on this bit!
@BornAgainCynic0086
3 ай бұрын
Make sure the printhead slides left to right BEFORE starting this! **** VERY IMPORTANT********Make sure the prinhead slides left to right BEFORE starting ANY OF THIS! You do this by doing a printhead clean with the cover open (put a screwdriver on the switch to bypass the open cover warning) and watch the printhead, when it moves to the left, pull out the power. And he has left out how to remove the ADF top cover from the body of the printer.
Пікірлер: 37