THANK YOU SO MUCH FOR MAKING THIS VIDEO! This helped me get Klipper going on my Octopus board and even a total computer idiot like me got it working.
@EdwardBraiman
2 жыл бұрын
You're welcome.
@Chanman1172
2 жыл бұрын
I just wanted to take a minute to thank you. I have spent the last few days trying to get Klipper and Fluidd working with my SKR E3 V2.0 board and this video is the only one of the 5 I watched that mentioned powering the board with USB power from the Pi and sure enough, that is what I was missing! I don't know why, but after trying the install that way I have FluiddPi running on my Pi 4, and Klipper running successfully on my converted Ender 3. Subbed.
@EdwardBraiman
2 жыл бұрын
You're welcome.
@Cyb3rGlitch
3 жыл бұрын
Thanks for the video! Small thing, at 3:15 PSK stands for 'Pre-Shared Key'.
@twistedsocal
2 жыл бұрын
glad that was pointed out
@BrettCulley
3 жыл бұрын
another great video, maybe down the road you might do auto bed level sensor tutorial on the BTT skr v2.
@EdwardBraiman
3 жыл бұрын
Waiting on parts from Musumi to arrive.
@johnm.gerard1718
2 жыл бұрын
Maybe this is new but an easier way to setup WIFI is the click on the GEAR icon in the Raspberry Pi Imager. Then you can scroll through the WIFI options. This is much easier. I don't know if this option was available at time of filming. also, with earlier versions of the imager you had to hi light the Gear icon and do a certain key sequence something like Command, shift, X that will pull up the WIFI settings Option.
@EdwardBraiman
2 жыл бұрын
True, but my issue is hiding part of my network from user's. Grant mine is not what it seems when you see things. I give away a little with ARP,, but that not the actual ID.
@ThekingofBAC
3 жыл бұрын
In pi imager you can select some advanced settings and enable ssh, set host name and password and set ssid and password for wifi. Just use ctrl+shift+x before write.
@EdwardBraiman
3 жыл бұрын
Cool.
@jetro6543
3 жыл бұрын
Great tutorial👌 In your opinion is it worth it to change firmware from marlin to klipper?
@EdwardBraiman
3 жыл бұрын
Depends on your tastes and preferences. There's been a request I talk about the subject and explain installs and configurations. Also it's a new challenge to take on. The configuration side is next and this weekend if the mods for the Ender arrive I designed I'll start tackling other tutorials.
@Zodiak146
3 жыл бұрын
Thank you - very clear instructions. But i got problems to configure my TMC5160 with Octopus + Klipper. Maybe you can help. [tmc5160 stepper_x] & [stepper_x] section
@ZhuJo99
2 жыл бұрын
To send same command again, you can click it in console or in input field hit cursor arrow key UP and enter :)
@EdwardBraiman
2 жыл бұрын
True, but for tutorial I'm overly obvious.
@ZhuJo99
2 жыл бұрын
@@EdwardBraiman true, but people who are skilled to replace the board and flash the firmware are for sure skilled enough to understand what’s going on :)
@johnm.gerard1718
2 жыл бұрын
I also Have an iPad so I just use an app call Net Analyzer. This app gives me all the devices on my network for pi IP address.
@ikkianachan8182
2 жыл бұрын
Very good tutorial. I did not get the serial usb when using ls comment in /klipper directory but it show up eventually when using ls comment in the main directory /fluid pi :). Even the one doesn't know coding can understand the logic in it.
@EdwardBraiman
2 жыл бұрын
Thanks.
@tepproctor
2 жыл бұрын
Is the process the same if I'm just switching from a gtr to the octopus? I already have the pi setup with my voron 2.4 but my gtr blew up.. do i just skip the first half and just skip to installing firmware to the octopus and so forth? Thanks for any help and sorry for the rambling..
@EdwardBraiman
2 жыл бұрын
There similar boards
@AlexG207
Жыл бұрын
Done everything and says printer isn't ready and the klippy host software is attempting to connect. I just need to hook up my hot end and end stops right?
@EdwardBraiman
Жыл бұрын
Printer should connect without endstops. Lack Thermistors can cause connection issues.
@kenfield-bg4uu
Жыл бұрын
BIG FYI. Only use 32GB sdhc Cards. It took me 8 trys to figure this out.
@EdwardBraiman
Жыл бұрын
Was it formatting issue?
@Muz994
2 жыл бұрын
I'd lke to implement an emergency circuit using a safety relay to cut the power to all the PSUs, but i'd like to avoid to shut down the board itself when the ESTOP is triggered. Do you think that i could keep the board powered via USB during normal usage? I'd also like to be able to trigger such emergency circuit from klipper itself in case of thermal runaway or other issues: is it possible to program an output pin to control something like a logi level MOSFET to shut down all the PSUs in case of malfunctioning?
@EdwardBraiman
2 жыл бұрын
Anything is possible. I generally don't show emergency power recovery as the print is already compromised the moment it occurs. So in my opinion it's value is low.
@Muz994
2 жыл бұрын
@@EdwardBraiman @Ed's 3d Tech I'm not referring to power loss recovery, i only need to physically cut power in case of danger. I can manage everything using a relay and an emergency button, but i would prefer not to cut power to the board, and i would also like if the board / Klipper could cut power themself if something went wrong. As my machine (which currently runs with linuxcnc) is quite large, uses nema23 motors and is used in a working environment i have to keep all the safety features I currently have, but i'd like to switch to a more common printer controller like this, linuxcnc isn't really built for 3d printers.
@EdwardBraiman
2 жыл бұрын
Sounds like a good 👍
@ahmettaruz280
2 жыл бұрын
Dear Sir, thank you for your perfect video, btw l build a corexy big size then install fluidd copy from your video :) but ı see a fail can you say something about it ? Option 'x_offset' is not valid in section 'heater_bed' ı check to heater bad section but there are no any x_offset line thank you for your help
@EdwardBraiman
2 жыл бұрын
There's a Discord link in description. And there's a Klipper section.
@VolvoWhat
9 ай бұрын
So i imaged the pi and it was able to boot with webcam errors for Fluidd, am able to ping on my network but i cant get the fluidd UI to load on a browser from my desktop on the network any suggestions?
@EdwardBraiman
9 ай бұрын
There's a link in description for Discord and either myself or someone else can help you in general chat.
@jackwood6214
Жыл бұрын
Do you have a newer video? I was told to look for videos no older than 3 months old due to changes
@EdwardBraiman
Жыл бұрын
For fluidd pi, there are new issues. I have some newer videos in BTT Manta series for CM4 pi, but steps are slightly different.
@jackwood6214
Жыл бұрын
@@EdwardBraiman I'm buying a Voron from a local guy, I'm trying to figure out how to change the wifi settings on the Rpi
@armandoortiz2497
2 жыл бұрын
i followed your video all the way to 15min from that point on i just cant flash this thing i dont know what im doing wrong
@EdwardBraiman
2 жыл бұрын
There's a link to Discord in description and a Klipper section were people can help.
@almaidah1
3 жыл бұрын
For some reason I cannot access serial id
@EdwardBraiman
3 жыл бұрын
It may mean firmware is not installed. Check to see if firmware.bin is renamed to firmware.cur.
@almaidah1
3 жыл бұрын
@@EdwardBraiman thank you
@EdwardBraiman
3 жыл бұрын
You're welcome.
@johnm4962
2 жыл бұрын
my octopus has a stm32f407
@EdwardBraiman
2 жыл бұрын
In that case select other processor.
@johnm4962
2 жыл бұрын
the clock speed is also different
@EdwardBraiman
2 жыл бұрын
I think defaults will appear in Klipper, but you can look at printer.cfg at topp to see them.
@beauvella32
2 жыл бұрын
Ls /Dev/serial/by-id No directory exists After successfully flashing octopus
@beauvella32
2 жыл бұрын
Solved set to USB pa11/12 Not can bus pa11/12 In menu config
@LordAndyvaile
Жыл бұрын
@@beauvella32 where did you get to menu config i have same problem thanks
@beauvella32
Жыл бұрын
@@LordAndyvaile make sure it's set to USB.
@LordAndyvaile
Жыл бұрын
@@beauvella32 i understand that but where did you find menu config ?
@LordAndyvaile
Жыл бұрын
its ok i im thick lol i went back in and it is set to usb thanks
Пікірлер: 55