I did not have to watch you at the range for 10 minutes shooting with crazy over the top music or silly attempts at humor or trying to look all Mr. Joe Cool Tactical before you got around to presenting your info.Great job! I learned something in under an hour.
@rooster3019
4 жыл бұрын
A tip you did not show: Remove the elevator before drifting the rear sight AND place a clean cleaning patch under the buckhorn so as not to scratch your barrel.
@tearsofaliberalclown949
9 ай бұрын
or a business card.
@lorentcase1023
Күн бұрын
Yes !
@lightotw
2 жыл бұрын
To see how much you moved the rear sight with the punch, first put some masking tape on the barrel in front of the buckhorn, slightly underneath the front edge. Trace the shape of the sight front edge on the masking tape. Now as the sight is tapped over, you can see if it was a little or a lot or maybe didn't move at all yet. Someone on another comment on youtube called this making a witness mark.
@G.I.JeffsWorkbench
20 күн бұрын
Good trick. Thanks for sharing.
@QtheLaserDude
11 ай бұрын
My elevator broke years ago, and I just held my thumb under there to adjust before I got it replaced. Worked far better than it had any right to.
@bobbyjoe9669
6 ай бұрын
Use a wooden match stick
@slotcarfan
Ай бұрын
My Henry 22 windage was off. I used dental floss to line up front, buckhorn and center of hammer on the bench at home. Went to range perfect! For elevation, with front sight buried in buckhorn notch at lowest setting it shot about 1.5 inches to high at 25 yards. I carefully used round fine to increase notch depth on my buckhorn. Reblued the notch with cold blue. Didn't have to replace with higher front sight and got it to print 3/4 inch high at 25 yds, so about zeroed at 50.
@savethewolves5628
2 жыл бұрын
Put a piece of tape over the barrel immediately in front of the rear sight where there is a point indicator. Use a pin to mark on the tape where the point is before beginning. Then tap lightly until you notice the point move from the pin mark and mark this new point on the tape and fire the rifle. Continue this until you get you windage where you want it.
@hugostiglitz2388
9 ай бұрын
At the dovetail end, the sight is pointed. Add a piece of masking tape with a pencil mark here on the barrel and line things up. than tap sideways with a wooden dowel. A pencil width will work out to 1" at 50 yards. The pointed sight tip is the pointer, the marked tape is where you currently are prior to adjustment. Easier to know where you're going when you already know where you are.
@Mascotal
5 жыл бұрын
Good tip Mel. Thanks
@TimD9804
4 жыл бұрын
Here's some old school. Make a pencil mark on the barrel right at the sharp point at the front of the rear sight. When you drift your sight, you will be able to see how far it's moved.
@jasondaniel918
4 жыл бұрын
Great tip. Thank you. You used floss to align the sight. I guess it is okay for me to use thin fishing line. It seems the line would accomplish the same purpose, and the fishing line will be more substantial in my arthritic hands.
@MeltheNut
4 жыл бұрын
To be honest, I used floss because the bathroom was closer than the garage where the fishing line was :)
@jasondaniel918
4 жыл бұрын
@@MeltheNut Thank you for the reply. And thanks for the reassurance.
@kingpin7673
5 жыл бұрын
1001 uses for dental floss. Good tip.
@want2boutdoors274
4 жыл бұрын
Awesome tip
@Ramrod1948
2 жыл бұрын
Thanks for sharing, will be big help!
@paulbrungardt9823
3 жыл бұрын
Why not supply an O ring/ peep sight standard as opposed to buck-horn sight?
@anthonycesario4056
3 жыл бұрын
I like it. Good idea.
@ruger3089
9 ай бұрын
Good video, thanks for the tip.
@quovadis1767
2 жыл бұрын
Thanks for this nice idea
@TheGearhead222
3 жыл бұрын
Dear Sir-What sight picture do you use? I only ask, as my Rossi 62 shoots 8-10" high past 25 feet. This is with the front sight post underneath the target and the top of the post /target group aligned with the top of the rear sight. Appreciate any feedback-John in Texas
@Smurf5738
2 жыл бұрын
I'm taking a trip to the hardware store today to get some steel and screws to make an adapter plate to put the sights off of my pellet rifle onto my marlin lever gun. It has the windage and elevation adjustment knobs. Gonna be less of a headache to sight in when I'm done. Screw buckhorn sights
@michael184272
4 жыл бұрын
Very informative thanks for posting.. do you have a video on removing the front site? Just got the 1895cb and installed the williams peep onto the rifle..relized that I needed a taller front site and ordered the Williams Rifle Bead 570M and now for the install..
@MeltheNut
4 жыл бұрын
I do not, but it is my understanding that the sight gets knocked off right to left and then back on left to right. I would use a brass punch to do the knocking. Many new sights / spacers need a little bit of gunsmithing to be installed. By that i mean you may need to file the sight a bit to get it to fit in the grove.
@jimbro650
Жыл бұрын
Thanks Mel👍
@OBNXS1
5 жыл бұрын
Nice trick but glad I didn’t have to use it. My Henry would probably be a dead nuts tack driver in better hands than mine. As it is it makes me look like an awesome shot.
@Squib1911
5 жыл бұрын
My Henry Big Boy rear sight is at minimum elevation and the rifle shoots a little high. I added a Skinner rear peep and it shoots low when on the ground and it shoots high when I am in a tree stand shooting down onto the target. Screw it. I guess I will just finally get an optic. Despite the issues with the sights, I love the gun.
@TheGDizzo
4 жыл бұрын
Hrmm.. this would seem to contradict, what I was told on lever guns for windage, when I looked into it. You tap the front sight over within the dovetail. Which is apparently why BOTH my 336 AND 1894 .44 mag when I first took receipt from the dealer... both had a front site blade that was soo ridiculously loose you could reach up and move it back-and-forth 2-3mm within the dovetail! Apparently it's customary to move em back and forth and then peen the edge of the dovetail a lil bit over with a punch once you've got it so it will then stay there. The rear intended to provide elevation adjustment only. I need an optic anyway with my vision these days, so I just dabbed some blue loctite onto that front site blade, eyeballed positioning it centered along the barrel, and called it a day.
@Yettiattack
Жыл бұрын
You can drift either the front or rear sight. Does not matter. Alot of rifles have a little doodad inside the rear to loosen an move so you dont have to drift.
@rosalvareyes5241
3 жыл бұрын
Thanks brotha
@mike196425
Жыл бұрын
I'm guessing that to install a buckhorn sight you would do the same thing? I have a 30/30 that someone put a scope on and the missus wants iron sights on it.
@algentry1
5 ай бұрын
Thank you.
@easttexan2933
Жыл бұрын
Good tip. Well done. I noticed your buckhorn sight was almost in the last elevation notch. I'm guessing you were still shooting low. I had to purchase a taller front sight and do some filing down to get POI the same as POA with the rear sight at its lowest setting.
@Yettiattack
Жыл бұрын
He should be shooting high with it towards the top of the ramp.
@easttexan2933
Жыл бұрын
@@Yettiattack I agree....he should. However, it should not have to be adjusted to the top notch to get to point of aim, so like every Marlin I've ever owned, a taller front sight is needed.
@xade7863
Жыл бұрын
@@easttexan2933 I had to do the same thing to my Henry 223 single shot
@easttexan2933
Жыл бұрын
@Daniel Nelson yep
@xade7863
Жыл бұрын
@@easttexan2933 I’ve found the higher sight post with the ramp set at the middle notch and then filed it down till it was shooting perfect at 100 yards worked the best and I can still use the ramp for closer or farther away shooting
@williamcrawford7982
3 жыл бұрын
If the remlins would do there jobs right we wouldn't have to do anything!
@garypudup2109
Жыл бұрын
Geez, I just make a mark on the barrel with a pencil. Wipes off when I'm done....no tape, no floss, no big deal...:)
@Oneofthetwelve
5 жыл бұрын
Hi Mel. How’s it going with the accuracy. Be great to learn about how you are doing. Cheers.
@MeltheNut
5 жыл бұрын
I was able to get my windage set perfectly, but elevation was still a problem with my new Marlin 1894 .357. I have since switched that gun over to a Skinner peep sight. That sight is working great for me.
@Squib1911
5 жыл бұрын
@@MeltheNut my Skinner rear peep helped me with accuracy, as I am more accustomed to that sort of sight, but I am still having elevation issues on my Henry Big Boy. My next step is to finally get an optic and see if that helps. Still, I got two deer in 2018 with it. I like the rifle.
@MeltheNut
5 жыл бұрын
@@Squib1911 My peep sight worked perfectly on my Marlin 1894 .357, but on my old JM marlin 30-30, I had to buy a new front post to fix elevation issues.
@Squib1911
5 жыл бұрын
@@MeltheNut as far as I know Henry doesn't currently offer a replacement front sight that would help with this issue for me on that model of rifle. That was my initial desire to fix the elevation issue. I will have to remove the Skinner rear peep in order to install a scope mount, but if I can still use the buckhorn sight a s a backup, then I will keep looking for a Henry or aftermarket replacement/ adjustable front sight.
@MeltheNut
5 жыл бұрын
@@Squib1911 You should contact Skinner directly and see if they have a front sight option for your rifle. Can't say as I love the look of the their front sights, but they work. Also, they do need a bit of gunsmithing to make them fit right.
@mandovapehater6988
3 жыл бұрын
That's cool but if I wanted "perfect" id take those itty bitty screws off the top of that receiver and put one of em er scopes on it. 😛👍
@MeltheNut
3 жыл бұрын
True, scopes are king. But in WI, sometimes the weather doesn't allow for such awesomeness. Have to go low tech to beat the wind, rain, and snow.
@Mark-mq1cc
2 жыл бұрын
I take my brass punch and hammer to the range....hmmmmm
@mikesalmon9945
6 күн бұрын
Take your lunch and hammer to the range. Tiny taps
@westvirginiafishingdudeout7841
10 ай бұрын
What if I’m shootings 25 and I’m 6 inches high on the lowest setting
@MeltheNut
10 ай бұрын
You need a new front post. Check out skinner sights websight for one.
@bnscholet911
4 жыл бұрын
Fishing line might work better
@montycrain5783
4 жыл бұрын
The Elevator historically was used to adjust for different ranges . Elevation can also be adjusted by height of front sight.
@daerokosgalvan6041
Жыл бұрын
what gun is that?
@MeltheNut
Жыл бұрын
It's an old Marlin "Glenfield" 30-30
@greymanphipps8996
7 ай бұрын
My dovetail slides left and right after each shot.. cant tighten, total garbage
Пікірлер: 62