Thank you for the great idea TJ!! ❤❤ I just finished putting my shelf together and building three spooling setups. Looks great!! Now just time to try it out. Love your videos by the way❤❤
@TackleJunky81
2 ай бұрын
Right on! Appreciate the comment and thanks for watching! 👊
@willtrax71
5 ай бұрын
I just started putting a small spooling stand together after watching this and I found an Old 1911 Recoil Spring I’m going to Cleave in Twain for resistance lol, this is a cool video my friend.
@TackleJunky81
5 ай бұрын
Good deal man! Appreciate you watching! 👊
@5.7.0bassin2
5 ай бұрын
Best thing I do to unspool a reel get a bolt some washers and a nut if you have a empty line spool or really anything put the bolt through the spool washers and nut then put the thread end in a chuck drill and unspool a reel in now time
@TackleJunky81
5 ай бұрын
Yup, I do the same. 👊💪
@brianlee9074
5 ай бұрын
I use a similar setup, but without the bushings and springs. Bolt it to the same type of shelving too. Works great. Thanks man. 👊
@TackleJunky81
5 ай бұрын
Right on brother! 👊
@riccochet704
5 ай бұрын
I have one I built for my boat. Cost me $10. First piece is a 3/4" dowel from lowes for $6. I cut it to the width of my center storage locker, so it sits in the lid opening, but doesn't fall in. Second was two spring clamps from Harbor Freight for $2 each. Put your spool on the dowel, clamp the dowel in place in the center storage compartment. BOOM...I keep those on my boat. It's cheap, it's fast, I can respool a reel quickly on the go while sitting between the seats. I've seen all kinds of contraptions and devices sold for doing it on a boat, many costing a lot more. This is by far the cheapest I could come up with and it works so dang good. I've shown it to a lot of people in my club and they all use this method now. Now, there's no tension built in, but we employ the Iaconelli method of spooling and run our line through a towel soaked in line conditioner. That provides the tension, and doubles to condition the line as it's going on the spool. If you've ever spooled fresh line and tensioned with your fingers you'll notice this chalky powder that's left behind. Going through a towel of conditioner removes that. That being said, BRAVO, sir! I'll be picking up the supplies to build one of your spooling stations in my shop.
@TackleJunky81
5 ай бұрын
Right on brother! 👊💪
@frankofstad4558
5 ай бұрын
I used cones from a couple of wheel bolts instead of bushings, that way you can change manufacturer and always have the spool centered and "tight". I also used the foot from a articulating lamp so that it was movable and turnable, flat sided for spinning reel's and rolling for baitcaster's (i dont have a dedicated workplace for my fishing gear)
@TackleJunky81
5 ай бұрын
Right on! 👊💪
@PhilGeary
5 ай бұрын
nice job jim the spring tension is the most important part of your design , i have made free standing spool station without springs and the bolts would tighten or loosen as you spooled up would drive me nuts lol
@TackleJunky81
5 ай бұрын
Thanks man! 👊
@Grimey_Fishing
5 ай бұрын
I'm so glad you did this vid, James! I've been wanting to copy the earlier version of this that you used in the line spooling vid that Big Shirley recorded. I was going to figure out mods to suit my purposes, but you've already done that for me!
@TackleJunky81
5 ай бұрын
Right on brother! 👊
@Cornelius798
5 ай бұрын
Love that setup, especially including rubber washers. 👊
@TackleJunky81
5 ай бұрын
Appreciate you watching! 👊
@futureMDmom
5 ай бұрын
Love the new spooling station.
@TackleJunky81
5 ай бұрын
I bet you do! 😉
@davidwilliams1805
5 ай бұрын
Great job TJ! My son has one set up almost exactly like yours and it works great. Thanks again for some great content.
@TackleJunky81
5 ай бұрын
Right on brother! 👊
@erichildreth7562
5 ай бұрын
This is a nice setup and respooling your reels should be a breeze!! Thanks for sharing this with us!! :)
@TackleJunky81
5 ай бұрын
Appreciate you watching! 👊
@PaytonHatfield86
5 ай бұрын
I put a pegboard "paper towel holder" on my fishing wall and it fits thin spools of line great, thinking about bending the end back straight so it can hold wider spools of line, too! Cost me like $5
@TackleJunky81
5 ай бұрын
There you go! 👊
@chrishaener8702
5 ай бұрын
Someone got an A in shop class! Well done!
@TackleJunky81
5 ай бұрын
Thanks man! 👊
@basslesschap346
5 ай бұрын
Slicker than vasoline insoes !
@TackleJunky81
5 ай бұрын
💯
@jamesdishman3359
5 ай бұрын
Very cool I just use a short piece of wood dowel on my bench vise and two rubber bands
@TackleJunky81
5 ай бұрын
Right on! 👊
@MrJohnB-qs6dp
5 ай бұрын
Pretty Cool!!! Like that setup!!! Stay Safe & God Bless!!!!🤠👍
@TackleJunky81
5 ай бұрын
Thank you brother! 👊
@SROTV..southernrebeloutdoors
5 ай бұрын
I bought one on wish 2 years ago paid 6 bucks for it now they have it for 4.79 I still have it use it a lot works well with the 100 to 300 yard spools and 1/4 lb spools definitely won’t fit bulk spools though but mine clamps to anything that. The clamp fits on to I take it with me everywhere a long with my tub of spools of line But great idea for people
@TackleJunky81
5 ай бұрын
Right on brother! 👊
@SROTV..southernrebeloutdoors
5 ай бұрын
@@TackleJunky81 but I kinda have already implemented your idea tho prior to getting my line spool thing lol i just didn’t know much about KZitem or id of posted a video of it lol im finally getting the hang of this KZitem video creating thing hope to have more content put out fishing more of southeastern and southwestern Illinois would love to get together sometime and fish if you would be interested
@jvfishingfever
5 ай бұрын
Great video TJ. I'm going to set one up myself!
@TackleJunky81
5 ай бұрын
Right on! 👊
@Jason-416
5 ай бұрын
Nice 👍
@TackleJunky81
5 ай бұрын
👊💪
@jay.fishin
5 ай бұрын
nice dude 👍
@TackleJunky81
5 ай бұрын
Thanks man! 👊
@DaveWashburn
5 ай бұрын
Hey TJ, cool easy idea! I’m digging it👊
@TackleJunky81
5 ай бұрын
Right on! 👊
@madison.outdoors
5 ай бұрын
Awesome. I just got some coupons from ace hardware in the mail today to buy this stuff
@TackleJunky81
5 ай бұрын
Right on! 👊
@Oldbasshole
5 ай бұрын
Very well done ! I use a big carpenter’s/artist pencil and my toes lol I’m very low tech
@TackleJunky81
5 ай бұрын
That works too! 👊💪
@5.7.0bassin2
5 ай бұрын
Definitely building me one of these
@TackleJunky81
5 ай бұрын
Right on! 👊
@dickiehoskins9835
5 ай бұрын
Smart man! Great idea man. Great video
@TackleJunky81
5 ай бұрын
💯 👊
@c.shoefish
5 ай бұрын
That's a great set up, I'll definitely be doing something like tha when i move. Holding the spool with a spatula handle between my feet is getting old 😂🤣
@TackleJunky81
5 ай бұрын
🤣🤣🤣
@c.shoefish
5 ай бұрын
@@TackleJunky81 gotta do what you gotta do. I feel spoiled when my kids are around to help me😂
@stevesmith7164
5 ай бұрын
Great tips Jim
@TackleJunky81
5 ай бұрын
Thanks man! 👊
@offthehookdetroit
5 ай бұрын
Awesome setup
@TackleJunky81
5 ай бұрын
Appreciate you watching! 👊
@anthonythompson3447
5 ай бұрын
Thats a great setup and im definitely doing this. What if you soldered or epoxy the washers and spring together? So when you have to change spools its just one peice and the wing nut.
@TackleJunky81
5 ай бұрын
I'd imagine that would work as well.
@rvfishingyet
5 ай бұрын
Fun stuff Tinker Junky!
@TackleJunky81
5 ай бұрын
💯
@paulwyman2299
5 ай бұрын
You and Debo should have a segment home made fishing hacks .
@TackleJunky81
5 ай бұрын
💯
@Bass23
5 ай бұрын
Great idea thanks for the info👊👍💪
@TackleJunky81
5 ай бұрын
Appreciate you watching! 👊
@gixxer420
5 ай бұрын
Nicely done.. Preciate the idea..
@TackleJunky81
5 ай бұрын
Appreciate you watching! 👊
@jonahlawrence6204
5 ай бұрын
Great job
@TackleJunky81
5 ай бұрын
Thank you! 👊
@mikegrieshaber169
5 ай бұрын
What a great video 🎣🎣
@TackleJunky81
5 ай бұрын
Thank you! 👊
@jerryg957
5 ай бұрын
Nice build !
@TackleJunky81
5 ай бұрын
Thank you! 👊
@bigrywhat
5 ай бұрын
That’s a good idea. Would work well on a standard work bench I bet.
@TackleJunky81
5 ай бұрын
💯
@Brian.Heavner
5 ай бұрын
Nice setup, all I use is spinning reels. Tried a quantum baitcaster combo from cabelas, it was junk
@TackleJunky81
5 ай бұрын
Appreciate you watching! 👊
@trapin68
5 ай бұрын
Awesome! Now let's see your solution for spooling a spinning reel, because you can't spool them the way to can a Baitcaster. They are a PITA to put line on. I'm getting close to buying one of those fancy contraptions from Tackle Warehouse...but if you got a solution.
Make big Mike hold a pen and some finger tension like all us did for our dad when we was kids
@TackleJunky81
5 ай бұрын
He's to busy playing video games! 😂
@shaneroberts9264
5 ай бұрын
I built one a couple of years ago, very similar. I didn't use the bushings, but used two washer back to back. The problem I have is the spool will tighten the wing nuts down, to the point you can't stripe the line off the spool. Do you ever have any issues with the tension changing?
@TackleJunky81
5 ай бұрын
I've only spooled a few reels with it so far, but no issues yet.
@willtrax71
5 ай бұрын
A piece of a broken 2 piece fishing rod and a small Amazon Box lol I desperately need something better to keep constant and correct tension on my line, I have horrible OCD… thank you Jim..
@TackleJunky81
5 ай бұрын
Appreciate you watching buddy! 👊
@dougharlow6037
2 ай бұрын
Why not just grind off 1/8" off the brass bushing for smaller spool? It would still work on the larger spool. thanks
@TackleJunky81
2 ай бұрын
💯
@mohtashim5
5 ай бұрын
Whats that nylon bushing that you used?
@TackleJunky81
5 ай бұрын
It's a nylon bushing.
@BassFishingNEB
5 ай бұрын
I just have my wife hold my spools lol
@TackleJunky81
5 ай бұрын
That works too! 👊
@mattgivens8588
5 ай бұрын
I just watched several videos on line spooling and all the pros say not to lay your spool on its side when spooling spinning rods it causes line twist
@TackleJunky81
5 ай бұрын
It works for me. Appreciate you watching! 👊
@dannylang7971
5 ай бұрын
Where did you find the bushing to fit the spool?😊
@TackleJunky81
5 ай бұрын
Ace Hardware.
@dannylang7971
5 ай бұрын
@@TackleJunky81 thanks for answering my question, and that’s a great way to spool a reel, I like to spool a spinning reel with a cordless drill, put in on the holder and turn the spool with the cordless drill works great.
@danieltucker5899
5 ай бұрын
💪
@TackleJunky81
5 ай бұрын
👊💪
@eugenefoster9120
5 ай бұрын
Offer lots of trouble just fill a reel spool!
@TackleJunky81
5 ай бұрын
Appreciate you watching! 👊
@MaineStreamFishing
5 ай бұрын
Wow thats crafty!
@TackleJunky81
5 ай бұрын
💯
@Sstaley09
5 ай бұрын
🎣👊
@TackleJunky81
5 ай бұрын
👊💪
@nigel7297
5 ай бұрын
👍👍👍
@TackleJunky81
5 ай бұрын
👊💪
@jonahlawrence6204
5 ай бұрын
👊👊👊👊
@TackleJunky81
5 ай бұрын
👊💪
@kayakfishingforpredators9107
5 ай бұрын
💪😎👌 👊🤜🤛 Gr8 ID
@TackleJunky81
5 ай бұрын
👊💪
@chriscurtis8577
5 ай бұрын
👊👊👊👍👊👍
@TackleJunky81
5 ай бұрын
👊💪
@callmecamo2
5 ай бұрын
Is there something wrong with pinching the line with your fingers? Free and you've always got them with you. Well, hopefully anyways.
@TackleJunky81
5 ай бұрын
My thumbs go numb within seconds, so this works better for me.
@XnnorDaveB
5 ай бұрын
👊💪👉🤝🤛✌️🤘
@TackleJunky81
5 ай бұрын
👊💪
@westonmavis6566
5 ай бұрын
Very cool, think I’m going to steel this idea. 🥸 thought, you could have just trimmed the bushing for the small spool.
@TackleJunky81
5 ай бұрын
That would have worked as well! Appreciate you watching! 👊💪
Пікірлер: 121