Those rounded edges and corners really make a difference in terms of aesthetics Awesome build. I'm glad KZitem recommended me this video.
@SoundBlab
3 жыл бұрын
Thanks!
@ta563
3 жыл бұрын
That is an awesome little subwoofer. I liked the comparison clips with and without it; they really showed that a good subwoofer can add to the music even if you don't want to rattle the walls. Some people think subwoofers are just for specific types of bass heavy music or people that like to listen really loud; this one fills in the music so well.
@SoundBlab
3 жыл бұрын
Thanks man!
@SoundBlab
3 жыл бұрын
The first 1,000 people to use this link will get a 1 month free trial of Skillshare: skl.sh/soundblab08211 The BUILD PLAN for this project can be purchased here: soundblab.net/build-plans/ . It includes a comprehensive 21 page description of materials, parts, etc. on how to build this speaker from beginning to end. There are also many other BUILD PLANS from previous projects to check out!
@endall39
3 жыл бұрын
Very fond of this speaker design and execution. I have built a dozen or so speakers with the 5.25" version of this driver and I have never been able to get the ported versions to work as well as the PR designs. I've tried round ports, slotted ports, and flared round ports. I get port noise, or early distortion, or just less output. I suspect there is a very good sweet spot for the ported designs, but they are hard to find and by the time you discovery you have an issue, it's pretty much too late to do anything about it except start over. You may have to play around a bit with weighting the PRs, but that's pretty easy to do and the results are consistently good! Thanks for sharing this fine piece of work!
@georgenicolaidis7550
3 жыл бұрын
Had same issues with ported designs for the W5, all my builds were a failure unable to get a correct port resonance frequency implied by WinISD. Finally I bought a Dayton Audio DAT V3 to measure the drivers and guess what - all advertised specs where all over the place in my samples. If you get a spec for a Fs of 45 HZ and in reality you measure 59-65 HZ for the production samples you have a problem, and no there was not any improvement after burning in.
@SoundBlab
3 жыл бұрын
Yeah, these do require some long ports for a small enclosure, but it can be done without port noise. This one does not actually produce much port noise at all. Excited to see what the PR version will do. Stay tuned!
@fido139
2 ай бұрын
From experience, you have to stuff subs with fiber to keep the high bass from being boomy.
@beeshorts2743
2 жыл бұрын
I bulid this subwoofer 😀 And I don't know why I like this video so much I watched so many times and I never bored you're amazing dude👍
@SoundBlab
2 жыл бұрын
Thank you so much 😀
@Simjedi
3 жыл бұрын
I purchased the plans for this awesome little build. Thanks! Couple suggestions, include the internal volume and imperial measurements also. Some WinISD/BassBox Pro graphs and the SketchUp file.
@SoundBlab
3 жыл бұрын
Thanks for the support and feedback! I can do that for future plans. I dont have much experience with imperial measurements, so that might take me some time to implement…
@asmahanumer
2 жыл бұрын
Man I love this. Especially the the music combo!! Now I know what to do with the subwoofer I have ✔️🙌🏼
@SoundBlab
2 жыл бұрын
Awesome! Thank you!
@StickySli
3 жыл бұрын
I have two W6-1721 I snagged for 50$ each in Spain with only a nail scratch on the surround. The motor is impressive since it's an underhung midbass driver. It's not even considered a woofer, but with the 29 liter enclosure in a bookshelf format and 75mm port, which is not recommended for their performance, they still manage to impress me with the low notes. Tang Band produces incredible speakers. If anyone wants to build a banging bookshelf speaker, you could even place the W6-1139SIF as the woofer and a full-range speaker like a BMR for the upper frequencies.
@Randommmmm204
3 жыл бұрын
Only experience I've had with Tang Band is the Logitech Z2300 subwoofer, basically a rebranded Tang Band 8 inch (can't remember the exact model). In it's original box with it's original amp, it was very loud at about 45Hz, but that's everything it had going for it. Box was too small to go any lower and the amp was horrible. I made a custom box, used a Dayton plate amp and it actually performed very well, especially considering I paid like $50 for it. It could go as low as 28Hz with quite a bit of authority, and the quality itself was much better. I used it for a party though and I blew it up, which is actually impressive because that sub is tough. I've seen people plug them straight into wall outlets and they'd last for like a minute or 2. I don't know why people hate on that sub so much, the driver is actually really good. It's the amp and box design that suck. Not the box quality though because it was actually built really tough. They used good glue, nice quality wood and bracing which is unusual in such a cheap sub.
@tobitechboy1461
3 жыл бұрын
I’d love to do this one day!
@andymuzzo8568
3 жыл бұрын
Very smooth
@SoundBlab
3 жыл бұрын
Thanks
@gerardpastorelli4389
3 жыл бұрын
Perfect small set up with great sound, as everytime nice craftmanship !
@SoundBlab
3 жыл бұрын
Thanks
@birthmarkonthelefteyelid
3 жыл бұрын
The way you make these are on another level 🙂🎚️
@SoundBlab
3 жыл бұрын
Thanks man!
@mcolossi
3 жыл бұрын
Sei il migliore🤟
@SoundBlab
3 жыл бұрын
🤙🏻
@manjulwalia1995
3 жыл бұрын
Awesome bro.. now you used amazing music in the build video that i loved a lot
@SoundBlab
3 жыл бұрын
Thanks a lot!
@faustopf-.
3 жыл бұрын
My goodness marvellous piece of work!!!!
@SoundBlab
3 жыл бұрын
Thanks
@yankis.
Жыл бұрын
Really clean
@SoundBlab
Жыл бұрын
Thanks
@ahmetsahinarslan8842
3 жыл бұрын
8:00 döşeyelim abi (let's furnish) from turkey 🇹🇷
@hondashadowfrontcaliperrebuild
3 жыл бұрын
good stuff! great craftmanship
@SoundBlab
3 жыл бұрын
Thanks
@antonioroccella8908
11 ай бұрын
High professional work👍
@SoundBlab
11 ай бұрын
Thanks 👍
@ashleydaniels1132
2 жыл бұрын
stunning. once my money starts coming this month, im putting together one of your builds. i also want to build myself a pretty loud system too,er for my dj stuff, but big enough to use in my yard or large places. i dont play out much anymore......wonder why...lol, but i just want to know i have some head room to play with of the need arises. however sound quality is important to me too. any ideas??????? yes, more towards a budget friendly price range than a higher end.. not saying i wont watch that and who knows maybe even build that one too later on. keep bringing these builds on man. out of this world.
@SoundBlab
2 жыл бұрын
Cool thanks
@santoshwhy2943
3 жыл бұрын
Small and beautiful design I like it. 🙏
@SoundBlab
3 жыл бұрын
Thanks
@glengatt3941
2 жыл бұрын
Yes it is nice it can easily pass for something from a store, larger size is different or the same principle like 18 inch driver,gsg has one in a form of a kit and it's easier to just buy that but the shipping alone it will cost me 3 times as much as the actual product
@diamond527
Жыл бұрын
My choice soundBlab ❤️💚❤️👍
@SoundBlab
Жыл бұрын
Thanks!
@barenecessities5261
7 ай бұрын
Awesome build! Noticed you ran the round-over trim router over the brad nails. Doesn't this damage the router bit or cause the mdf to split maybe?
@3DLearningResources
3 жыл бұрын
Your Speaker designs are great . Do your have Tutorials for how to make speaker enclosers , I want to learn from you .
@SoundBlab
3 жыл бұрын
Tahnks man! Not yet, but might do that in future sometime.
@rezo786
3 жыл бұрын
really amazing work. would really like to see you build a 10" or 12" or even 15" . something that can product below 30Hz with minimal dB loss
@SoundBlab
3 жыл бұрын
Thanks. Will do something like that soon in fiture hopefully 🤙🏻
@thepirateswirled
2 жыл бұрын
i definitely enjoyed this video, nice job!
@SoundBlab
2 жыл бұрын
Awesome, thank you!
@Frambhueee
Ай бұрын
Hi, what's the average volume of the inside of the (or) 4" woofer?
@Riktamroyindia
3 жыл бұрын
Awesome 🤩👍 From India 🙏🙏
@SoundBlab
3 жыл бұрын
Thanks
@user-dc3pd7us6e
2 жыл бұрын
What is the f3 on this sub? Do you have the frequency response graph? Edit* it is said in the video that it has an f3 of 35hz
@alonewarrior9737
3 жыл бұрын
Great work...
@SoundBlab
3 жыл бұрын
Thanks
@Bruno-oj3zb
18 күн бұрын
what round corner bit you use ?
@yendizof5309
3 жыл бұрын
Saya ge bisa bikin nu kitu mah ,, cuman ga punya alat alat bro 👍
@hoomanAdnan
3 жыл бұрын
Amazing art piece ❤️🔥 Love from Bangladesh 🇧🇩
@SoundBlab
3 жыл бұрын
Thanks man!
@hoomanAdnan
3 жыл бұрын
@@SoundBlab welcome 😊
@bryanadam3306
2 жыл бұрын
I very like make yourself. Please explain your makeup electric plates join the speakers.I live in Myanmar country. Thank you.
@ctrlblahq5631
3 жыл бұрын
amazing bro !!!!! greetings from chile bro!!! :D
@SoundBlab
3 жыл бұрын
Thanks
@JoeGP
2 жыл бұрын
nice, but looking at the price list, you probably spent $300 on that, you can buy a Magnat sub with that, that i think is nicer. I looked into building some bookshelf speakers, but buying some ready made ones (Magnat Monitor Supreme 102) was gonna cost about the same, so i did. I am building my own amp though.
@wandersonuhuu5902
2 жыл бұрын
Olá amigo,você pode ajudar com um projeto,tenho um woffer de 6.5 polegadas de 180w com o fs de 44 hetz,um par de Tweeter domo de seda e um radiador passivo de 6.5 polegadas também, qual litragem você me indica pra esse projeto?ou ficaria melhor uma caixa de 16 litros com dutos?
@antkoos
2 жыл бұрын
Could you please share a link or a name of the song that you used in the first subwoofer demo?
@rover8772
3 жыл бұрын
Nice build.. No line in on that plate amp, only BT?
@SoundBlab
3 жыл бұрын
Yes, it has a line in.
@litoboy5
2 жыл бұрын
Cool
@SoundBlab
2 жыл бұрын
🤙🏻
@phaneendramulagala9287
2 жыл бұрын
Sir i have 12” car subwoofer tube so how to convert into ported enclosure with required size
@adolfoeugeniowalser6809
2 жыл бұрын
Demaciado rigida la caja dando perdida en resonancia y los caños de pvc largos causan distorsion y hondas estacionarias si ¡
@AmongTheHorizon
3 жыл бұрын
Nice Build! I have 2 w6 1139 SG at home and maybe I build one of your 2 designs (Passive Membrane or BR) for each driver Today I use each w6 with a 8 Inch PR in small box, but it needs a better rebuild.. At 14:32 it looks like your AUX Port isn't sealed at the end and maybe cause some problems with airflow generated noises. While listening to the sound demo at the end, I would like to know if you use the full range signal for your stereo speakers when the subwoofer was off or did you use a highpass/speaker protection crossover for them? I appreciate your work and looking forward to the next part.
@SoundBlab
3 жыл бұрын
Thanks. The AUX port is sealed, so luckily no noises from it. I just plugged the ports on the stereo speakers, no crossover except on the sub.
@dyamant2005
11 ай бұрын
that looked like it took a lot of time to build
@SoundBlab
11 ай бұрын
The finishing takes the longest, the enclosure however can easily be knocked out over a weekend.
@pi-tech1817
3 жыл бұрын
Bass wow
@SoundBlab
3 жыл бұрын
😎
@pi-tech1817
3 жыл бұрын
@@SoundBlabmy subwoofer produce distortion n produce smooth bass , please help me
@dryferreira3101
3 жыл бұрын
Perfect 👏🏽😍
@SoundBlab
3 жыл бұрын
Thanks
@masminlabstv5494
3 жыл бұрын
Awesome
@SoundBlab
3 жыл бұрын
Thanks
@mihkus
3 жыл бұрын
Looks fantastic but how do you stabilize the mdf panels from expanding and contracting with air moisture? Doesnt the paint crack over time?
@SoundBlab
3 жыл бұрын
The paint does not crack, but you can see very faint join lines on some of the joins. It really is only noticable close up.
@phinguyen4371
2 жыл бұрын
i'm in vietnam, but i really want to buy your products
@migueldamian5276
Жыл бұрын
WILL YOU HAVE EXAMPLES OF HOW TO BUILD A SPEAKER FOR A 4-INCH MINI SUBWOOFER?
@SoundBlab
Жыл бұрын
Not currently, but I can consider it as a future project.
@deltwin8277
3 жыл бұрын
song name?
@rezo786
3 жыл бұрын
just a question. after applying sanding sealer did you need to lightly sand before applying primer ?
@SoundBlab
3 жыл бұрын
I applied two coats with sanding in between and after the final coat with 320 grit.
@youtubemega5121
3 жыл бұрын
Why the subwoofer is not moving?
@fredgeitner713
2 жыл бұрын
I noticed when you built your "Dynamites" You had mentioned that you didn't use brad nails because you intended to round the corners, however on this build you did. Did it cause any issues when you rounded the corners? Any damage to the bit? I love the rounded corners and would like to do the same thing.
@SoundBlab
2 жыл бұрын
I did not have trouble with the bit getting damaged, however you will need to punch the nails back into the wood a bit afterwards and use a good quality wood filler to fill the holes. Over time the wood filler can also push out as the wood moves. This creates small but visible bumps on the surface of the paint. Best is to not use nails at all if you can.
@fredgeitner713
2 жыл бұрын
@@SoundBlab Thanks for the reply. Are you punching the nails into the wood deeper before the corner rounding, or after you have already rounded the corners and are preparing for the final finish?
@kallew7628
2 жыл бұрын
hi, nice video ;) ... i have one question; won't you hit the nails with the roundover bit, when rounding the sides? or did you remove them behore doing so?
@SoundBlab
2 жыл бұрын
Thanks. Sometimes I do hit them yes, but more often that not I try not to use brad-nails when I know I am doing round overs.
@protim9947
2 жыл бұрын
Can anyone tell me the name of the song which starts at 9:14
@crazyworld1727
Жыл бұрын
whats your Plywood Thickness?
@SoundBlab
Жыл бұрын
think it was 16 or 18mm
@BrenttttttMCMXC
3 жыл бұрын
is this available in overseas?
@beeshorts2743
2 жыл бұрын
MDF thickness and size ?
@SoundBlab
2 жыл бұрын
16mm or 5/8inches
@Fcoiltamar
3 жыл бұрын
Perfeito
@SoundBlab
3 жыл бұрын
Thanks
@afprojektcz
3 жыл бұрын
👍
@SoundBlab
3 жыл бұрын
🤙🏻
@kirantalla7159
2 жыл бұрын
Hi sir I want to buy a subwoofer to my Bose home theatre how can I buy from you please let me know please
@SoundBlab
2 жыл бұрын
Sorry man, I dont currently sell physical products, only build plans on my website.
@birumutiara2169
3 жыл бұрын
could you tell why there is a couple of small and medium hole inside seperating 2 room? why not close it up completly and make the low freq only come out from pvc pipe
@SoundBlab
3 жыл бұрын
The wood panel with holes inside is a brace to help reduce cabinet resonance or vibration. You need the holes to so that air can move inside the entire volume of the cabinet.
@birumutiara2169
3 жыл бұрын
@@SoundBlab to "reduce resonance" are you sure not the opposite, to enhance resonance? like brace inside acoustic guitar. i thought brace is to enhance resonance so it can sound louder.. wow all this time i was so wrong thank you vr much sir now you have me as a new subscriber
@SoundBlab
3 жыл бұрын
The brace is glued to the inside of the side, top and bottom panels to refuce their vibration and avoid the panels from causing to much resonance. Speaker enclosures perform best when we can have a very ‘dead’ cabinet and only the speaker drivers are doing the work since cabinet vibrations can influence the sound negatively. A guitar is different because it relies on the cabinet to help produce the sound. The braces inside the guitar is there to tune that sound.
@birumutiara2169
3 жыл бұрын
@@SoundBlab ok.. Thank you vr much for this new info🙏 please keep up the wonderful work like this on and on..cheers
@pujisupradipto9977
3 жыл бұрын
is there a schematic for this speaker box?
@SoundBlab
2 жыл бұрын
Yes, check the link to the build plans in the description.
@carswnova
2 жыл бұрын
Does the skillshare link still apply?
@SoundBlab
2 жыл бұрын
This is the latest one that applies: skl.sh/soundblab06221
@carswnova
2 жыл бұрын
@@SoundBlab thank you so much. Built my first pair of speakers last year, got lazy and actively crossed and amped them but a friend asked for a similar speaker build without my (amp and crossover) complications so I'm trying to learn how to make good passive crossovers. I just wish we had good parts suppliers in South Africa like parts express
@rayapudimastanrao2422
2 жыл бұрын
👌👌👌👌
@SoundBlab
2 жыл бұрын
👊
@djSpinege
3 жыл бұрын
Why did you cover the amp with what looks like petroleum jelly ?
@SoundBlab
2 жыл бұрын
It is clear silicone. It is needed to seal the gaps around some of the connectors to make sure the enclosure is airtight. If not done you can get some air noises through some of the connectors.
@mastermhine2982
3 жыл бұрын
Hai sir can u build GT-12BP BOX sir
@SoundBlab
3 жыл бұрын
Hi, sorry but I don't have such a project on the cards right now.
@anandshah71
2 жыл бұрын
How to connect this subwoofer and your dynamites 2way to a stereo amp. I don’t have a 2.1 amp
@SoundBlab
2 жыл бұрын
You will need to have a plate amp in the subwoofer. You can't just run the sub also off the stereo amp. In the 2.1 configuration means the subwoofer is also powered by its own amp.
@anandshah71
2 жыл бұрын
@@SoundBlab I am new in this diy but I read somewhere a diy user made a 2.1 system the .1 is a dual voice coil driver is a sub and passive crossover of both left and right lower frequency can to the DVC sub
@manojkonar3969
3 жыл бұрын
Where is the power supply unit in this one?
@SoundBlab
3 жыл бұрын
External SMPS 24v 5A.
@yaghiyahbrenner8902
3 жыл бұрын
what is the size of that roundover bit ?
@SoundBlab
3 жыл бұрын
Its about a 20 or 25mm radius.
@surajdivate8965
3 жыл бұрын
Brother show us how to make Amplifier from old DVD player..and connect with LED TV
@TheLevitatingChin
3 жыл бұрын
No
@sbeezynukka
3 жыл бұрын
Do you know how much power supply and extra components would have to added to make that happen?
@surajdivate8965
3 жыл бұрын
@@sbeezynukka If i know that why would i ask ??
@sbeezynukka
3 жыл бұрын
@@surajdivate8965 it’s obvious you don’t, he could possibly add In a small chip amp because all of the audio circuits are pre existing but it’s easier to just add the amp at the preamp outs as the player was designed. Compare a stand alone DVD player to one in a HTIB setup then tell me if it’s worth the effort.
@SoundBlab
3 жыл бұрын
@suraj divate Sorry man, but this is just not within the scope of what I do.
@plainstupid9235
3 жыл бұрын
can I suggest screwing the speakers from the inside? so that the screws are not showing outside.
@carlosargueta3005
2 жыл бұрын
Where do you get your logos made?
@SoundBlab
2 жыл бұрын
These are resin dome badges. A search on Google should guve you a supplier in your area/location.
@yousifraja2368
3 жыл бұрын
👌👌👌👌👌👌
@SoundBlab
3 жыл бұрын
🤙🏻
@eballacharles0302
3 жыл бұрын
👍👌
@SoundBlab
3 жыл бұрын
🤙🏻
@rockstare8507
3 жыл бұрын
💘💘
@SoundBlab
3 жыл бұрын
🤙🏻
@Mix3dbyMark
3 жыл бұрын
Please sell me this sub
@johnthongbam1475
3 жыл бұрын
It's too expensive man
@Chinhnguyen0497
2 ай бұрын
how to calculator volume of speaker? calculator mean choose right volume, not calculator existed dimension
@gabrielv.4358
Жыл бұрын
"Small subwoofer" Small is 5 inch or below...
@SoundBlab
Жыл бұрын
Small in this case rather refers to the enclosure size, not the driver. And in comparison to large subwoofers, this one is rather small, not very small, but small. Of course though, size is all very subjective.
@heresjhonny702
3 жыл бұрын
"Subwoofer off" Sounds the same as my system WITH the subwoofer on... T_T
@thomasschafer7268
3 жыл бұрын
Sorry. 6.5" for 70-78€ is too expensive. A thomann 12-280 for 50€.12 INCH.
@newbutthunt
3 жыл бұрын
Really surprised he didn't round-off the inner brace openings and caulk the inside air-tight, I'm sure car audio guys are cringing rn.
@LKN117
3 жыл бұрын
Really depends on where the air moves. With this port design, rounding the edges on the internal brace really shouldn't matter. Also with as low pressure as the enclosure is under it should also be plenty well air tight. Running multiple large drivers creating tons of pressure inside the enclosure is when your really need overkill. something this small is fine to not go the extra mile.
Пікірлер: 158