The is a very good video how to make wing thanks great job
@trevor5290
Жыл бұрын
This is the best, most informative wing build video that I have seen yet. Thanks for taking the time to post.
@HB_Aircraft
Жыл бұрын
Glad you enjoyed it!
@TheWingnut58
10 ай бұрын
A tip for cutting the bevels.....place your straightedge about 1/4 inch away from the fold and use it to guide the top end of your blade....perfect bevels every time.
@rodchurchill5576
5 ай бұрын
I've been watching videos or few hours on how to do this . Yours is hands down the best . I love the one piece idea . The wet paper first is one some talked of hearing about but didn't do . The only thing I question is the fact you didn't appear to match the panel halves for length . I will being using this method for my wings .
@NIRAJPATELV
20 күн бұрын
Excellent help Thanks so much love your video Can u pls tell me what make is your exacto knife I like it a lot Cheers 👍👍
@HB_Aircraft
19 күн бұрын
K26 Fit Grip Knife by Excel Blades: excelblades.com/products/fitgrip-knife
@pjryan6226
Жыл бұрын
Good man.Im just starting to build myself and this tuition is perfect for me.Keep up the great work and I will get you loads of subs.
@jackjuhasz533
2 жыл бұрын
Just what i was looking for ! Thanks
@fuzzysphere
Жыл бұрын
Thank you for a truly clear and useful video. In your opinion, would this technique work for a much thicker airfoil, say with thickness 30% of the chord?
@cl18t
6 сағат бұрын
How my aileron reflex does this need?
@user-fy6js2mg2k
8 ай бұрын
Thanks
@smokeymcbongwater3561
Жыл бұрын
Way cool I’m building one thanks
@nathangrahl9939
2 жыл бұрын
If you are going to hotwire cut a solid foam wing cores, what airfoil matches the saddle on the fuselage?
@HB_Aircraft
2 жыл бұрын
E168 with a chord of 178mm and 100% thickness. This results in an airfoil that can be cut from a 1" thick foam blank. See: airfoiltools.com/plotter/index?airfoil=e168-il
@TheWingnut58
10 ай бұрын
Using a fully semetrical airfoil, draw a line from the center of the leading edge to the center of the trailing edge along the end of the wing....the bottom half is the shape of the wing saddle.
@ricardotrujillo7444
6 ай бұрын
I assume you mean elevons, not "elverons" right?
@donaldverhaeghe9603
7 ай бұрын
Do you have recommendations for cg. and control throws?
@HB_Aircraft
6 ай бұрын
CG about 1 inch from the leading edge. Elevator throws of about 20 degrees. Aileron throws of about 35 degrees. Use reduced throws for the first flight then increase them to your preferred level of responsiveness once the plane is trimmed.
@Tonynux
Жыл бұрын
is the wing 30 inches long?
@HB_Aircraft
Жыл бұрын
Yes the wing shown in this video is a 30 inch wing.
@ELIAS-og5vf
9 ай бұрын
Hello sir where can buy this bord and what is name plz
@HB_Aircraft
9 ай бұрын
You can buy the foam board from the FliteTest store: store.flitetest.com/flite-test-maker-foam-board-by-adams-20-pack/
@Lakshmidevi-ib3jr
2 жыл бұрын
what material is used ?
@HB_Aircraft
2 жыл бұрын
Foam board, it is foam with a layer of paper on each side. See: store.flitetest.com/flite-test-water-resistant-foam-board-by-adams-25-pack/
@TheWingnut58
10 ай бұрын
The foam board from "Dollar Tree" works great too...
Пікірлер: 26