Great content 🎉I learned a lot .. that is insane the inside of the motor😮 but good to know it’s common I never knew that! Thanks 🙏
@user-nz6bd1nm8q
2 ай бұрын
Great vid bruh, These nova engines got what it takes but yeah you MUST tear down and inspect everything before you start the thing. The G9R engine for on road is a monster
@JonathanStanley
2 ай бұрын
QC is a problem for them still then eh? Edit: The BRAAAAAAAAAAAAAPPPP is godly though ❤😂
@TheNitroAddiction
2 ай бұрын
Hell yeah brother awesome!!!🔥🔥👊
@allaspectsrc4178
2 ай бұрын
Looks nice
@TastyBRC
2 ай бұрын
Its looking much better than the first batch of Novas. The ports are Big! The crank window aswell! This engine is not designed for fuel economy ! Is the crankshaft still as tight as it was in the b5? This is very interesting, I wish I had one in my hands to check the numbers and compare it to my p324. If you are happy with it in the long run, I may try one 🤔 A shame for the wrist pin and the steel bearing.. but you cant complain, you got much better aftermarket service than me 😆
@thenitronation5815
2 ай бұрын
Yeah for sure, I’m much more happy with the t6r than the b5r the fit and finish is much better, the crank comes out of the block like it should. And it runs fantastic much more reliable than the b5r once again. End of this season I’ll disassemble this engine and see how it’s held up.
@nateharris1918
Ай бұрын
@@thenitronation5815 I bought this engine in febuary, and i have had nothing but problems with it. My initial experience was like yours, fired up and ran beautifully through the break in process. a week later i take the car out just to do some tuning and run some more fuel through it, did not touch any setting on the carb and it just gags on fuel all through the midrange. last week i tore the engine down, found the DLC coating has flaked off the crankshaft, midspeed needle had a torn o ring, . i was shocked at how easily you are able to remove the head and sleeve- i had to heat gun the snot out of mine and it was still very difficult to remove. i replaced the midspeed needle and took it for a quick test drive still acts about the same, just no power, always loaded up on fuel. can you tell me where your needle settings are at and what % of nitro you're running? ive been figting with this thing for 5 months and im at my wits end
@thenitronation5815
Ай бұрын
@nateharris1918 my b5r was like that, it was a dud just nothing went right with it. I would just try to return it like I did mine. I thought this t6r was going to be the same way but so far it has been flawless, break in was easy, took 10 minutes or less to tune, has lots of power and runs consistent. I run it on 30%
@danielwood4590
Ай бұрын
Looking good so far. I know you've got a roma aswell be interested to see how it compares as i love my roma but spares are very hard to find so would like a replacement engine.
@thenitronation5815
Ай бұрын
So far this engine is a blast and similar in performance to the Roma.
@EYESWIDEOPEN00
15 күн бұрын
Nova needs to hire some of Novarossi's prior builders or something. That's just careless engine assembly to have debris sitting in a fresh motor. They have a quality control issue. How do you get shavings inside of such a little engine. Do they pre run these prior to selling them? I just don't understand how you can have machining debris in a fresh motor. And in regard to the bearing, it must be old stock from Novarossi. Well they will learn quickly if this type of thing becomes a common issue. They should have been going above and beyond to avoid issues like these
@thenitronation5815
14 күн бұрын
They must not clean them enough after the final machining process, no they are not pre run. But I agree they really have to work on stuff like this
@jayp9299
2 ай бұрын
Love that bearing tool. Where did you get it?
@thenitronation5815
2 ай бұрын
AMain’s
@Nitro_rc_life
2 ай бұрын
Wow that's fu ked. Can't believe that with this new company I have seen a few like this now
@Cooldibs
2 ай бұрын
Are you concerned with the QC of this engine?
@thenitronation5815
2 ай бұрын
I was at first but I think it’ll be fine
@Cooldibs
2 ай бұрын
@@thenitronation5815 aka would you recommend me buy one of their engines for a buggy I’m building?
@dondagy9109
2 ай бұрын
Nova is novarossi. Thats why the old bearing.
@kyronrc
Ай бұрын
I was about to buy one of these, but now i just wont. They have 0 quality control for what it seems...
@thenitronation5815
Ай бұрын
Definitely seem hit or miss
@blameusa7082
Ай бұрын
Rocks are so overpowerd, need nerf!
@dylansowder6617
2 ай бұрын
Definitely wouldn’t be running any of those novas for racing ever since jarred Wiggins started running them he hasn’t been competitive seems like he is always having an issue
@jonpye8655
2 ай бұрын
Is he having an issue with the engine, or just problems in general?
@dylansowder6617
2 ай бұрын
@@jonpye8655 you didn’t catch all the metal that came out of it? You shouldn’t have to dis assemble a factory assembles race engine to check for metal and to actually find metal is just unacceptable
@kawicepticon8866
15 күн бұрын
The T6r isnt square , 17mm x 17.5mm...she rips no doubt , I have 3 2 of which are modded, but she isnt square
@thenitronation5815
14 күн бұрын
Not exactly no
@kawicepticon8866
14 күн бұрын
@@thenitronation5815 what do you mean "no". A square engine has the same bore as stroke , No engines made my Nova currently are square , their .24 engines are all .1mm less in bore and stroke vs the Novarossi Roma . 17.5 stroke and a 17mm bore isnt square. 17.5 bore and 17.5 stroke would be square
Пікірлер: 29