Perfect video. 20 minute installation.. thanks so much. Your adapter is great. One suggestion, please include a second zip tie for us old people. The first one got eaten between the seats and I had to tear my toolbox apart to find another. Great product!
@mustng9646
5 жыл бұрын
This video was dead on with the removal of the shifter knob . I watched a few and saw different methods. This is the way to go. Dave was one hundred percent right when he said to grab firmly and pull. Thanks for the video
@popodood
2 жыл бұрын
hahaha i thought you edited in the 3 different adapter, they just popped up on screen. but then you picked one up lol it was like a magic trick
@sonyatipton7264
Жыл бұрын
Thank you SO MUCH for this video. Now I just need to find the adapter. Ordered a Hurst T handle knob from amazon. Had all kinds of fittings with it but none would fit my 2012 camaro. Now I just have to find the Barton adapter and I'm all set.
@crymalthief6231
5 ай бұрын
How did you find an adapter and knob that fit, I'm looking for my 2012 but I don't know how to tell if it'll fit
@justinglebell
2 жыл бұрын
Thankyou for making this video!
@davemay7797
7 жыл бұрын
how can i order one of these
@chitownrider9247
5 жыл бұрын
Can you get the R for reverse on the left side instead of the right? Mines on left
@Anarchy1463
7 жыл бұрын
Hey David thanks for the video it was really helpful. Would you happen to know of any sites that sell that thread pattern 3/4-16 I haven't had any luck find a site to get a nice custom shift knob. Any information about this would be much appreciated thanks again.
@bucketoftruthify
Жыл бұрын
The plastic trim ring was by far the hardest most time consuming part of this. Had I known there are two barbs on the ring that hold it onto the knob, it would have been easier. I could see them in the hole, but brain did not engage until after flailing it off. Chewed up four or five harbor freight trim tools prying on that thing, but did not damage the boot. 6oz lighter than stock, I'm curious to see how it feels on the road.
@borri68
6 ай бұрын
I was thinking of using a hurst T handle type shiftier. Was thinking one could cut the top of the lever off that has the flat spots and cut threads on the remaining round part of the shaft, this way you wouldn't be stuck using one type of knob and it would have a shorter throw.
@Infidel67
2 жыл бұрын
Daaamn Thank you for this
@j.vazquez1752
6 жыл бұрын
Just received my shift and adaptor. Shifter ball / adaptor did not work. Seemed threads were off. Contacted Barton they are shipping another one tomorrow. Quick correspondence though.
@lacymartin608
2 жыл бұрын
Where I can buy this adapter ?
@OtherCoder6
2 жыл бұрын
Would this fit on the c6 corvette
@crypto_11
2 жыл бұрын
U should’ve rotated the adapter first so that the shift knob wouldn’t need that glue
@camarofan9612
2 жыл бұрын
I see what you’re saying. Put the knob on the adapter first, and then adjust the pins where they need to be, then remove the knob, do the work, and it’ll line up 👍🏻
@Steve-yw7ic
2 жыл бұрын
No big deal, the glue took 3 seconds. Easiest part!
@gml99
2 жыл бұрын
What size mm is the 2017 one?
@herbertruiz5090
10 ай бұрын
How can I take off the adapter after installed?
@TheINCDexter
Жыл бұрын
Dragon ball shift knob for automatic 5th gen would be nice
@Blakehenry11
Жыл бұрын
I like this setup much more so than the Speed dawg. I don't like how the boot on that one comes all the way up to the ball. My only gripe with this setup is that there is no jam nut to hold the ball in place or some sort of set screw. To me that would be much better than relying on Loctite.
@ejsn4128
2 жыл бұрын
where can we order this adapter
@thecarkid9667
7 жыл бұрын
Did Barton change their phone number?!?!? I tried calling multiple times but every time I get the message machine!
Пікірлер: 24