I connected my HHO generator output to fuel line that went to fuel tank. Then I took a peice of cardboard and covered air intake by 50%. This allowed for the correct fuel to air ratio. The engine governor will maintain proper RPM’s for your Frequency 60hz =3600 Rpm in US. My generator runs for many hours on a gallon of water mixture. My HHO Generator draws about 12 amps. I have a 960 amp battery hooked to a 30 amp battery charger that is plugged into generator that maintains battery charge level. The battery charger only draws 210 watts from the 4kw generator. I used dual water filter assembly to build HHO generator, one is HHO generator and the other filter case is water bubbler. Both are mounted on top of 4kw generator where the fuel tank used to be. Battery and charger are also mounted in same box on top. I use it to run my camper when I go boon-docking. I have run generator for 4 days straight. I added a extra tank for water and electrolyte as needed so I don’t have to get up in middle of night. I’m in the process of building a bigger HHO generator for a 10kw generator for my house.
@yourworkshopmate372
Жыл бұрын
That is really awesome to hear!! You have motivated me to continue on this project when load shedding isn't too hectic here in south africa. Thanks so much for your comment. Really appreciate it.
@raloed.363
Жыл бұрын
So 12Vx12A=144watts. You say the battery charger pulls 210watts from generator. So that is an efficiency of 145% after everything. But the generator should be around 50% efficiency max. So that means you will be generating around 420watts worth of HHO using 144watts of electrical power from the battery. So your claiming to literally run your engine on water. That is what your saying right ?
@Yangmist3r
Жыл бұрын
Interesting... I wish you could show us some videos of your set up. Exploring HHO for electricity generation is really tempting.
@julianguzman2321
Жыл бұрын
Saludos y gracias x sus comentarios.le pregunto alguna vez a podido medir con un amperímetro el máximo de amperes utilizado solo con hidrógeno? Estoy en comienzo de hacer lo mismo y me ayudó su comentario,gracias.
@francoisbinneman7084
Жыл бұрын
How much HHO does your generator produce per minute? Is there a way to calculate the minimum volume of HHO required for a 4kW generator for instance?
@johnhenke6475
2 жыл бұрын
Hook the HHO line to the carburetor fuel line and restrict the intake by half like that guy in Spain did. There you have throttle control. One third of the gas in free oxygen so the engine does not need to breathe as much atmosphere. So don't forget to half way block the intake.
@KristjanSaarsalu
Жыл бұрын
did you try it out, and its working?
@yamatocoaching7864
Жыл бұрын
I think you need more HHO gas, I think you can get more out of this by using more amps and make the bubbler smaller, and use a smaller gas powered engine so you can easily troubleshoot.
@DEWclassicgarage6206
Жыл бұрын
Can you send that link too?
@Leonardo-hq1zg
Жыл бұрын
@Practice on Listening I think is the crazy channel
@Leonardo-hq1zg
Жыл бұрын
@@DEWclassicgarage6206 I think that is the crazy channel
@MrDonovano
Жыл бұрын
I built one like this. Cut my fuel bill in half. A 9 cell generator. Swapped out the 304 with 316 as it tarnished quickly. I used Epsom salts for conductivity. Been toying with the idea of running my gennie as well 👌
@yourworkshopmate372
Жыл бұрын
Awesome! Thanks for commenting. I think that's a great idea I think I also need to swop my plates to 316.
@howardosborne8647
Жыл бұрын
So long as you are just toying with the idea all will be good. When you start trying to run a generator on a theoretically over parity device(free energy) the reality will dawn that it is all nonsense.
@terrancebecker9092
Жыл бұрын
@@howardosborne8647 you misunderstand. this has NOTHING to do with perpetual motion. an AC unit makes more btu cooling than the power it uses. this is simply a matter of how efficent the HHO making process is. BUT... that doesn't mean this guy's setup works...
@vivianjordan
Жыл бұрын
I love your south African accent,love from south Africa
@woodzyfox4735
10 ай бұрын
Best HHO snake oil I have seen so far!!
@jonmitchell9019
Жыл бұрын
To make it work you have to have the carburetor choke off half way with a piece of card board. Take off the air filter cover half with a piece of cardboard in there and put the air filter back on and run it. It can only run on the HHO gas if it is choked off.
@Benakuzo2
11 ай бұрын
Just completed the break-in period and so far the unit is operating perfectly kzitem.infoUgkxOTeIs0vv4_9B5hsmnLsk9r930uDQLu_Y . I was amazed by just how quiet this little guy is. I kept having to walk down the driveway to the generator to make sure it was still running. In fact, the most annoying noise coming from the set-up is a high-pitched chirping coming from the pressure regulator on the propane line. I suppose it's possible my other propane-powered generator's pressure regulator is making the same noise, but the generator itself is so loud I've never noticed it. Build quality so far is excellent. My only nit is the service panel is a little tricky to remove. I feel like I might break off one of the plastic tabs when bending it back. I probably just need to work out the technique, so will not hold it against Champion.Next week I intend to fully load the unit to charge a large battery pack and will update this review if there's any problem (3000W continuous load vs a rated 3100W capacity while using propane). Absent any trouble there, I'm 100% pleased with this purchase.
@TheJagjr4450
Жыл бұрын
IF you do not change your ignition timing then AT BEST the engine will run roughly. The problem vs gasoline is that hydrogen needs to be lit later in the engine cycle. It takes a long time for gasoline to completely burn which is why the spark is initiated much earlier. Hydrogen burns in a fraction of the time so what happens is max cylinder pressure is reached prior to the piston reaching TDC thus if there is not enough momentum to keep the engine rotating the engine is stopped due to pressure. The spark timing of a petrol engine is 10 degrees or so prior to TDC whereas you need to light the mixture at TDC.
@jontanneguy4960
2 ай бұрын
Stan meyer said you can modify the burn rate of hho by adding non combustible gases like using an EGR
@shbabar2000
Жыл бұрын
simply great
@KurtBoulter
Жыл бұрын
Thanks for the video, quick point, did you know, you can buy a triple fuel carburettor, for most generators motors, from Chinese manufacturers sites, which I won't mention, as I will be deleted for commercial content, that allows you to run unleaded petrol, LPG and Natural Gas. The Natural Gas ability is the pest, since it is low pressure and would suit brown gas or hydrogen. With your current setup, connect everything up as you had it, restrict your intake to 50%, and add a valve on your gas hose going to the generator and allow your hydrogen generator to build up a little gas pressure against the gas production and water pressure, before turning the tap on, then, before attempting to start the engine, open the valve slightly to release a constant flow of gas.
@yourworkshopmate372
Жыл бұрын
Thanks For your comment. I'll definitely try this in the near future. But with the current load shedding we have in South Africa I will experiment on my generator when the crisis subsides. 🙂
@fuelban
Жыл бұрын
Opposing flow holes restrict flow, use straight through holes, ... Think flow, if you had to run a football field side to side you're going to create less to.. straight thro... And better one 10 mm flow hole for example than 2 or 3 smaller hole's. For example.. sizes only.. choose you're own hole size to suite flow rate, which reflects plates surfaces... Good video.. Thom in Scotland.
@yourworkshopmate372
Жыл бұрын
Thanks for your comment. Really appreciated.
@mr.patent6329
Жыл бұрын
interesting solution
@ulyseknight7674
Жыл бұрын
That single-hole you have going into the carburetor in that piece of clear PVC you need a second hole so you can regulate air as much as fuel
@johnnybron2237
7 ай бұрын
If you build a hydrogen cell with neutral plates, one side of a neutral plate will only produce hydrogen, the other side of the neutral cell will only produce oxygen. If you do that setup for the plates you can then build gaskets with separated ports - one direction pure oxygen - the other side of the cell Hydrogen only. Then you could run straight hydrogen into the generator. Also if you get a couple of powerful magnets and put them on each side of the hydrogen cell plates - the extra magnetic electric current will boost production of the cell.
@markhill4256
Жыл бұрын
With my battery charger hooked to 4kw generator, I have around 3790 watts. The manufacturer says at 50% load it will use 1.5 gallons of gas in 10 hours. At 50% load of HHO, It uses around 1.5 liters HHO/ min. I still have 2kw of power left. I did put a 3200 watt load on generator for 1 hour. To get 10 hours using more than 50% load I will need around 3.5 gallons of water and electrolyte. Still working on lower amp draw on battery.
@martindamerau5722
Жыл бұрын
Hi Mark, thanks for your helpfull comments! How many cc has your generator (displacement)? I´d like to know how many litres HHO/ min. I´d need for mine.
@jr-pl9kj
Жыл бұрын
hydrogen has a faster flame speed than gasoline, diesel etc. ignition timing has to be changed closer to TDC, plus a carburetor is not needed, you have to change the fuel delivery system to a cng or lpg type setup.
@jontanneguy4960
2 ай бұрын
Stan Meyer said the burn rate can be reduced by adding non combustible gases. This can be achieved by adding an EGR to the system.
@wernerjaskolka7689
Жыл бұрын
Is the genertor a 2 stroke or 4 stroke. Lubricating oil is normally added with the fuel. I cant see hydrogen alone providing enough lubrication in the long run. 4 stroke engine should work.
@realfrankandrade
2 ай бұрын
USE A SMALLER HOSE FEEDING INTO THE FUEL LINE! 1/4 inside diameter should be fine. AND KEEP THE LENGTHS SHORT! You don't want the hho having to travel 10 feet before arriving at the engine. Keep it under a foot or less.
@hhoschool
Жыл бұрын
Good job
@Healitnow
5 ай бұрын
1. To prevent heat use a lower power setting. It will not generate as much hydregon but is safe. 2. Make another electrolysis unit and hook it up to the same gas liine. This will double the fuel to the engine. Keep making and adding more units until you create enough to run the motor unstarved, like it was on gas.
@abdulmainaDIYs
Ай бұрын
What elecrolyte is the best, this thing blew my mind,watching from Kenya Africa
@realfrankandrade
2 ай бұрын
You need more plates and more water. Use distilled with just a little potassium hydroxide. And use stainless steel 304. The water's quality affect the amperage problem/ require more energy problem. YOU MUST USE DISTILLED, and keep minerals away. They lower the waters resistance. I read somewhere that the best water was ocean water. Im going to be buying a 3000 watt and do away with the utility company. They're raising rates by 75% here in Cali and solar energy is not reliable enough. Cloudy days. Rain. Get a spare too. And power everything from water.
@Kennys_World
Жыл бұрын
Idea: Quit trying to make the generator make its own hydrogen while running… instead make the hydrogen separately using solar or wind power. Then tune the generator to run 100% on hydrogen. You’ll ideally need to compress the hydrogen into a tank, so you’d need a decent sized battery bank that is recharged with the solar/wind and DC compressor. I think this is how the energy observer is making its own hydrogen to be stored for use in its electric engine fuel cell set up.
@yourworkshopmate372
Жыл бұрын
Thank you for your comment. Yes I think I'll have to do that.
@secondline5641
4 ай бұрын
Looks like there are couple issues 1 being your flash arrestor not allow higher pressure of gas through. 2 add a bubbler to Clean up the gas.
@Andy-df5fj
Жыл бұрын
You're trying to match HHO production to generator consumption which is a tricky balancing act. I recommend producing and storing the gas in a tank under a controlled pressure then trying to run it from a tank with an appropriate regulator the same as you would for a propane generator.
@yourworkshopmate372
Жыл бұрын
Thanks Andy
@IronMan-bl7dd
2 күн бұрын
Humm that gives me an idea thanks
@pwrstranger2197
Жыл бұрын
Maybe try an extension manifold for carb and plumbing a hydrogen fuel line into manifold behind carb... JMTC
@yourworkshopmate372
Жыл бұрын
Thanks for your comment. That is a brilliant idea. I will try that in a future project.
@philduv2339
Жыл бұрын
You need to inject a mist of water in your carburator because hydrogen burn faster then gaz and the mist will help the timing of the engine, or the water in your HHO machine needs to be at minimum 50 celcius to max 75 celcius so the mist do it by it self.
@cryptoethics1070
2 жыл бұрын
Greetings from Cape Town, I like your Flashback Arrestor... Am currently researching the topic and also plan to build an HHO powered Gennie. Some guys from Lima ( Peru) University ran a 200cc scrambler on HHO & Air. They removed the carb's float bowl and ran the HHO into the main jet housing. Not sure if the jet was modified or even removed. Been pondering if a 'Dual Fuel' carb might work & think one would also do well to retard the ignition timing a bit coz it's prob set at 20+ Deg BTDC. Good Luck!
@yourworkshopmate372
2 жыл бұрын
Hi Crypto ETHics thanks for your comment. I'll definitely look into that idea at a time when I dont need my generator too badly as for load shedding 😅. My wife was upset that I was experimenting on it. I once even flooded the carburetor with water, but luckily I managed to get it working again😅. But I'm excited about trying different ways in the future.
@cryptoethics1070
2 жыл бұрын
@@yourworkshopmate372 Loadshedding sucks & I don't expect it (or the petrol price) to improve much... Built a fancy ups setup 2 yrs ago to keep my PC, Hifi & lights etc running but got fascinated by HHO recently... The Peru project bike is btw called the 'ShaibertOxi' if you want to google it. They ran it on a 250 km test circuit first with petrol then HHO. Used 7L petrol vs 1/2L water. Clearly 'over-unity' to me.
@yourworkshopmate372
2 жыл бұрын
@@cryptoethics1070 OMW that is awesome!! I'll check it out now!!
@yourworkshopmate372
2 жыл бұрын
Good on you for your set up, well done!!
@johnhenke6475
2 жыл бұрын
@@yourworkshopmate372 There is a guy in Lahore Pakistan building them for motorcycles. Forget about a patent of getting rich. In the states I know of two who tried and they are dead. It's a death sentence in America. Just open source all of it. These things are easy to build and the MAN can't kill everyone.
@marknewton3280
Жыл бұрын
how about reduce the hose size at the intake, its like hose just dumping it out but you put your finger over it and voila you, a stream.
@joeldsouza4860
8 ай бұрын
Get a 2 wheeler gas conversion kit. Fit the setup to the carburettor. It will work.
@joeldsouza4860
8 ай бұрын
Your HHO gas output needs to be collected in a tank and the volume of output needs to be about 2 litres of gas per minute per 100cc. At this rate if your generator engine is about 250 cc.... You will need to produce 5 litres of HHO gas per minute. This can happen by increasing amp output as well as increasing the wattage while keeping voltage at around 6v.
@mikekoster9
Ай бұрын
I going to try a propane kit but use hydrogen. Im hoping I can adjust/modify mixer to get the proper amount of hydrogen/air fuel ratio.
@copelandrobinson
Жыл бұрын
Maybe try a large reservoir before it’s hooked to the generator to give you more volume?🤷🏼♂️
@jasonjaffray4025
2 жыл бұрын
Maybe try changing engine timing to match the hho burn speed... I think 🤔 hho has oxygen already so remove Carb... Also... 👍
@yourworkshopmate372
2 жыл бұрын
Awesome! Thanks for commenting Jason I'll definitely try that method one day when load shedding isn't too bad, as I need my generator at the moment. My wife was so worried that i was going to damage the generator when i made that video 🤪😆
@jasonjaffray4025
2 жыл бұрын
@@yourworkshopmate372 😂 for sure.. I look forward to your next attempt... 👍
@secondline5641
4 ай бұрын
There is also a float an needle in the carburetor by pass the carb
@user-vk5ws3jl1l
Ай бұрын
We use electricity to split wateratoms to be used as hydrogen gas fuel. Why not build an engine to run directly on electricity. Shorten the process and you have less energy loss, more efficiency. Or this could be the future if we could get hydrogen from water without electrolyse. Eventually we might be able to build engines that run in sync with infinite energy surrounding us.
@bagdadimas
3 ай бұрын
The timing in the carby will have to be adjusted for the hydrogen as it has higher combustion, therefore you won't be able to use the petrol and switch the hydrogen. If I could suggest maybe add another hydrogen cell to increase the fuel capacity and give that a go.
@primodernious
Жыл бұрын
you dont need the carb just regulate the trottle with a valve.
@shbabar2000
Жыл бұрын
simply i believe we should promote this than who needs petrol pumps
@yourworkshopmate372
Жыл бұрын
Yes, and it's been proven that you can run a combustion engine on just fumes.
@stevenphillip1159
Жыл бұрын
Make two more separate hydrogen fuel cells and you will get it to work
@HG-Pilot
6 ай бұрын
It is all about air to fuel mixture. Try to allow air in and control the amount of it. As it is setup now you ate suffocating the engine.
@martinrochejocquelein1772
2 ай бұрын
The problem I have with hho is not making but winter weather freezing temperature..being in Southern Ontario winter can be interesting with freezing..hho is good in summer but useless for winter driving..even bringing in the hho system say inside the vehicle makes it a challenge
@BreannaHassecrets
3 ай бұрын
U need to put more pressure to it .there is not enough psi to run use a fish tank pump .
@fabiof6048
Жыл бұрын
try closing the air filter by eighty percent, maybe it sucks in too much air
@brianatkinson4484
Жыл бұрын
Have you tried fitting a propane gas conversion kit that uses petrol or propane & injecting HHO instead of propane
@yourworkshopmate372
Жыл бұрын
Hi Brian, thanks so much for the comment. That is a brilliant idea. I'm hoping to continue this project soon, When load shedding in South Africa subsides a bit, then I'll tend to the hho project again and I'll try your idea and let you know. Thanks again for commenting.
@jamesbeach1838
22 күн бұрын
Maybe a pressurized sub tank with a regulator to the valve that you made keeping the hydrogen pressurize may cause it to get to the Pistons quick idk just thought not a scientist or anything
@ATXMatt
3 ай бұрын
Check the experimenting BMW did with a V10 on ambient pressure hydrogen back in the 2000s 2010s. Bottom line, HHO gas will supply abouut 1/3 the power of gasoline at ambient pressure. If you want full power, you have to presurize the hydrogen to get more energy density. That is WHY this technology has not taken off. Presurizing Hydrogen is a costly endeavor in every way.
@kennethlarkins4086
5 ай бұрын
You should also remember that the burn time of hydrogen is much faster than the burn time of gasoline you would probably need to tune your machine accordingly accordingly
@issacbourne5111
Жыл бұрын
That being a very small motor, you probably giving it too much HHO. You need to rig up an adjustable valve inline where the HHO goes in. And a T fitting where the engine gets air with a valve to adjust that like how a choke works. The engine dying means you either way to rich with HHO, or way too lean. Also need to have a way to divert off the excess hho safely while you mess around with this.
@j.christie2594
Жыл бұрын
Try a Smaller Jet nozzle in Carb. Seal off Carb, completely, cause enough Oxygen is Present from Electrolysis device. See's that you need about 1-1.5 Liter's per minute to get that size engine to fire steady. I had these issue's in my experiment's. Also, what's your PWM value's? You need about min 4 Amp's 12 Volt's, to get enough gas for engine that size. Good luck with getting your Generator running in Self fueling mode, cause it can be done..
@yourworkshopmate372
Жыл бұрын
Thanks for your comment and motivation. I'll definitely try your method once load shedding has subsided a bit here in South Africa. My amps in the primary coil is 4 amps and the secondary coil is 50amps secondary coil the voltage is 14v. My measurement LPM is just under 2.5L
@j.christie2594
Жыл бұрын
@@yourworkshopmate372 I am not sure if i understand about Primary and secondary COil's, sound's like Tesla Coil arrangement. Pulse Width Modulator-PWM, with potentometer for Wave adjust, is what i understood to be Power source, I found on E-bay and Amazon.. I have smaller one (12V, 2.5 Amp's) that run's Tiny HHO device, Blow torch. Cost $5USD, I will be gettting or Building 5Amp, one soon for Bigger Cell and more out put. Good luck with your Build Sir. Hope to see New video soon, with it Running steady..
@juanbacyardtv8038
Жыл бұрын
👍
@hho-generator
Жыл бұрын
Very good. :)
@yourworkshopmate372
Жыл бұрын
Thank you for your comment much appreciated.
@laveniashaw5604
Жыл бұрын
I successfully ran a 5hp petrol pump on hho simply by inserting the hho hose into the air intake, no mods necessary.
@DirkLoots
Жыл бұрын
You need a gas control in front of the carbonator. This is a very cool setup. Please send me your contact details and we can exchange ideas. I am sure I can help you make this work
@chananon8120
Жыл бұрын
OMG! Fed's coming for us. The secret is out on HHO..... 😧😲
@basitbabar3884
10 ай бұрын
اسمیں آکسیجن کیٹ بھی ساتھ لگائیں جو ہوا سے آکسیجن الگ کر کے اسکے ساتھ میکس کرے پھر یہ سو فیصد کام کرئے گا۔
@Rajeshkumarvyas
Жыл бұрын
wow....i make this HHO generator but still unrun bike.....whay please give a sagestion please sir....
@bb8creations411
11 ай бұрын
Convert to steam ,use the generator to make hho gas to heat the steam
@bobdavis321
Жыл бұрын
Have you tried adding magnets across the HHO generator? I saw a video where that dramatically increased the amount of HHO generated.
@bobdavis321
Жыл бұрын
kzitem.info/news/bejne/r2uCv4hpcXepbGk
@bobdavis321
Жыл бұрын
kzitem.info/news/bejne/q2iE4KqEkJyenG0
@yourworkshopmate372
Жыл бұрын
No I haven't. Yes I've seen that it works. I'll try that hopefully soon.
@sawomirbuzdygan4167
Жыл бұрын
Piękna bajka
@bendere1488
Жыл бұрын
Hydrogen implodes. It does not explode. If you put water vapor/fog in with it, the hydrogen combustion creates flash steam. Patrick J. Kelly has some good info on water powered generators.
@yourworkshopmate372
Жыл бұрын
Thanks for your comment. That is very interesting.
@bendere1488
Жыл бұрын
@@yourworkshopmate372 Water powered generators are totally doable. I'm researching the cheapest and easiest solutions right now. You are welcome to join my online discussion group (can't put it here because of spam filters).
@yourworkshopmate372
Жыл бұрын
@@bendere1488 that will be awesome. How do I go about joining your group?
@bendere1488
Жыл бұрын
@@yourworkshopmate372 I commented but youtube deleted the comment. If you look in spam comments you might see it.
@woodzyfox4735
10 ай бұрын
I got some HHO stuff. I should make a video showing TRUE results while showing everyone no fuel in the bowel and so on 100% uncut
@merlin1346
Жыл бұрын
why dont you plug a small invertor into the generator to run an electrolyser and once the generator is started switch over to the generators electrolyser so it is self supporting.
@raloed.363
Жыл бұрын
Will only work if you generate HHO gas greater than 100% efficiency. You will need about 400% efficiency to make it self running
@merlin1346
Жыл бұрын
@@raloed.363 then others on youtube must have achieved 400% because they have shown them running, What is the 400% based on?
@raloed.363
Жыл бұрын
@@merlin1346 at 100% efficiency Faraday electrolysis generates 0.0114 L/min of HHO using 1.23 watts of power. You need about 5 L/min to run the generator, which is about 540 watts of electrical power. But even at 100% Faraday efficiency, the generator is still about 25 to 50 percent efficient at converting the HHO fuel into electrical power. So you need to generate enough HHO to overcome the loss in efficiency at the generator and still have enough electrical power to keep making HHO so the battery doesn't die. So for example 135 watts from battery must generate 540 watts of HHO. If generator is 25% efficient then it will output 135 watts of electrical power which keeps generating HHO without draining the battery. But the first hard part is reaching 100% Faraday electrolysis efficiency. As the industrial method of generating hydrogen is about 60%. However if you design the elctrolyzer right I'm sure you can reach 98% efficiency. It takes 1.23 volts to start electrolysis, so each cell must only have 1.23 volts across it. Meaning if you using a 12v battery your electrolyser must have 12÷1.23=9.75 ,approximately 9 or 10 cells in series. The cell gap can be 1 to 2 mm depending on the electrolyte concentration. Dry cells are more efficient than wet cells. The only method I know off that exceeds Faraday electrolysis is Voltrolysis. A method made public by Stanley Mayer in the 1980's but is now rapped up in psuodo science. The method uses a large inductor that resonates with the elctrolyzer(acting as a capacitor). The resonance pulse the water molecules with high voltage resulting in an increase electric filed strength that leads to the water molecules splitting and giving up electrons which flow as current. This current is not taken from the power supply but is produced from the electrolyser itself, thus reducing the overall power consumption. Voltrolysis uses low electrolyte concentration and is said to produce efficiency of over 1700%.
@Myshizniggs
Жыл бұрын
What about switching the carb to a duel fuel carb then trying th3 hho
@yourworkshopmate372
Жыл бұрын
Hi DJ thanks for your comment that sounds like a great plan
@hydrogen-power-gas
Жыл бұрын
Seams like you have along long way to go .
@yourworkshopmate372
Жыл бұрын
That is very true😁
@andremin1435
4 ай бұрын
When coupling the hydrogen directly to the carburator, all the hydrogen is sucked out of the hydrogen generator on first intake stroke..
@levimoya9205
2 жыл бұрын
You need more HHO going in try using a balloon 🎈 let it fill up then open valve that's going to carb the pressure will force the HHO in and start motor
@layt6342
7 ай бұрын
I ran mine into the breather however you need to get it just the right distance away I guess I should say that I took the breather off but whenever I put it inside of it it wouldn't ruin I had to back off of the hole a little bit it was like it was flooding but when I got it just write it ran like a champ
@lyndonsia5868
10 ай бұрын
Dear, please do not place a plastic cover, air is required in the combustion. It needs fuel and air mixture to ignite the engine. so just stick it to the air filter cover and that's it. make sure you suck air to your combustion chamber and not only fuel.
@FollowingChrist4eva
4 ай бұрын
I seen a man who used a vacuum chamber that his HHO cell was set up in and it only needed 1 -2amps tops to pump out litres of gas per minute. Try using a vacuum chamber. … … ..
@saywick
10 ай бұрын
Add 2 12v batteries parallel more amps more bubbles🍾
@user-po5xl8ux7v
4 ай бұрын
Really you have to adjust the engine timing almost to top dead center hydrogen goes much faster than gasoline gasoline is rather slow at the ignition reset the timing hopefully you can do it on that particular motor I'm sure you can just about top dead center otherwise it'll kick backwards I did this myself and I got thrown out of the United states for doing it so be careful 150
@asshole3569
5 ай бұрын
I have run a small engine on straight HHO. I forget the output you need but that is far from it.
@Herakles89
Жыл бұрын
I would said, that you have not enough hydrogen. i estimate, that you need a mininum of 2kw of eletricity for hydrogen production to run the Generator.
@skimowhite586
Жыл бұрын
There is not enough hho!!! You need to charge the water and use solar panels to run it during the day!!! Use a 6 tube cell to charge water at 12v runing all day. Use mo electrolyte. The use the water of the actual system and conect it to carburator. Problem is you have explosion but nothing but air to expand steam actually expands more just lower the ammound of water consumed or used!!!
@yourworkshopmate372
Жыл бұрын
Thank you for the comment I'll definitely put this to practice.
@unlmtd-gym
Ай бұрын
Hola la entrada del gas tiene que estar detras de la mariposa del carburador por eso no funciona , tienes que sacar el carburador agregarle un suplemento entre el carburador y el motor e inyectar el gas detras del carburador asi te va a funcionar, de la manera que lo pcolocaste solo toma gas y no oxigeno
@andreazanellato1982
Жыл бұрын
Ciao, ma usi solo hho oppure anche la benzina?
@thecesar971
Жыл бұрын
Is the problem too much oxygen going into the engine?
@kurtremislettmyr7108
9 ай бұрын
Not enough gas i imagine. Fill a big balloon, try running off that.
@bambur1
Жыл бұрын
It takes 3000 watts to make about 200 watts of HHO . im sure this works great
@yourworkshopmate372
Жыл бұрын
Thanks for the comment. I've seen others on you tube run combustion engines on hydrogen so I wanted to see if I could do the same.
@TheodoreAndor
Жыл бұрын
Yes choke air intake by half
@woodzyfox4735
8 ай бұрын
12 amps at 12v that's only about 1.5L per min. With a 96cc engine u have there u need at least 3L per min.. also with that charger running the battery ur losing even more energy then ur making . If anything it's slowing the discharge of the battery. If the battery is 960 amp hr battery it be HUGE. You make have a 960 crank amp battery. That could be a 12v 35ah battery. It won't run for days at a time. Do a time lapse video
@saywick
3 ай бұрын
Block half your intake and connect hho directly to the 4 stroke fuel intake line and your away
@wernerjaskolka7689
Жыл бұрын
Try it with a 4 stroke engine.
@yourworkshopmate372
Жыл бұрын
Thanks for your comment. This is a 4 stroke engine. Have a blessed day.
@ycy-technologies
6 ай бұрын
What did you use for electrode and electrolyte?
@Which-Way-Out
4 ай бұрын
316 stainless & Epsom salts
@joeyjennings9548
Жыл бұрын
use solar panels to make hho? then again thats just a complicated way to end up with the same energy?
@user-by2oo5qt5w
11 ай бұрын
Try separating oxygen from hydrogen.
@studiogala1
5 ай бұрын
you have to play with the timing on the engine
@studiogala1
Жыл бұрын
you have to set the timing to tdc
@shadiabuaalim8190
Жыл бұрын
Nice project ..but about apm
@yourworkshopmate372
Жыл бұрын
It draws 4 amps, and out the secondary transformer coil, its 50amps
@shadiabuaalim8190
Жыл бұрын
@@yourworkshopmate372 do you used any circuit for this project for control
@yourworkshopmate372
Жыл бұрын
@@shadiabuaalim8190 yes you can use a normal circuit. You can see how I made my AC to DC converter in another video. Very easy to make. I was running the hho generator with the generator when I made the video.
@shadiabuaalim8190
Жыл бұрын
@@yourworkshopmate372 about ..amp only 4amp to run
@yourworkshopmate372
Жыл бұрын
@@shadiabuaalim8190 yes because you put it through a step down transformer, which you can see in another video I made. So you step it down to 12v which will give you the high amps. But the primary coil only uses about 4 amps
@amazingtoolsvs
Жыл бұрын
You need 3lpm per hour to completely run this thing on ho at about 60 amps
@InverJaze
Жыл бұрын
I'm afraid that the lowest cost per KWH is still red Diesel.
@user-je9gs7we1q
Ай бұрын
What was that noise was it supposed to be music ?
@IonutMagdau-lp1ie
4 ай бұрын
Vreau și eu unul
@richardlove4287
6 ай бұрын
Not enough gas…bigger gas generator needed.
@WTF_BBQ
Жыл бұрын
Personally, I would never use HHO directly to the engine. We all know it's a equal mix of hydrogen and oxygen which is an explosive combination. It's probably not healthy for the engine to have an explosive mix anyway. If I were to experiment with this technology, i'd separate the hydrogen and oxygen, and use hydrogen exclusively.
@yourworkshopmate372
Жыл бұрын
Thanks for the comment. I thought about that, only afterwards 😬. Will definitely try this.
@WTF_BBQ
Жыл бұрын
@@yourworkshopmate372 FYI: If you want efficiency and higher yield of hydrogen, you can use the following components: 1. Use graphite plates instead of stainless steel 2. If you use stainless steel, sand the surface rough. It's all about increasinmg the surface area. 3. Use 1 Mole Potassium hydroxide instead of Baking soda.
@yourworkshopmate372
Жыл бұрын
@@WTF_BBQ thanks for the advice. I did try graphite but it seemed to oxidize quite a lot. I also tried copper using it as a cathode for the hydrogen, thinking that it wont corrode because it's not the anode, creating oxygen. But it didn't work and the copper turned black. But perhaps I didnt use the correct graphite. The graphite plates had a thin stainless reinforced mesh. I think the graphite was pressed.
@WTF_BBQ
Жыл бұрын
@@yourworkshopmate372 Water will start to split into hydrogen and oxygen around 1.8 - 2.0 volts. Most people will crank the voltage up to 12v which will definitely tear up your plates and produce excess heat and steam. They mitigate this by putting appropriate number of Neutral plates in between the Pos and Neg active plates which will divide the voltages to 2.0 per plate. My guess is that your voltage was too high with only 2 plates. The graphite will definitely tear itself into little flakes usually around 10v. This will also oxidize your stainless steel faster. I used to experiment with batteries and super capacitors. I see these problems a lot.
@yourworkshopmate372
Жыл бұрын
@@WTF_BBQ Thanks for your advise. I made a dry cell with with about 40 plates. You can check it out in one of my other videos. But I think, I am doing something wrong because I see other dry cells that produce way more using only about 35amps. My cell produces about 2.5Ltrs about 50amps.
@hermanvandherlek8769
2 жыл бұрын
If your try is true on this video, why not adopt HHO. some use kerosene, others fuel oil, others gasoline or HHO, as long as it starts the engine. you haven't tried it with electricity to see the intensity it will produce. my question is what it would look like on a 50 hp outboard motor.
@yourworkshopmate372
2 жыл бұрын
Hi Herman, I tried it with electricity from the mains plug point and it didn't work. It produces the same amount of hho as when plugged into the generator. So I tried it with a load (plugged into the generator) and without the load (plugged into the mains) thanks for you comment.
@hermanvandherlek8769
2 жыл бұрын
@@yourworkshopmate372 Can HHO start a gasoline or diesel engine without fuel or not? just start
@yourworkshopmate372
2 жыл бұрын
@@hermanvandherlek8769 Hi Herman, hho gas can definitely start and power an engine. But there are issues which I need to investigate further. As I've seen on other you tube videos they are able to run cars off a hho generator my size. So I decided to put it to the test. Either I'm doing something completely wrong (which I'm doing more research on) or those other youtubers wernt truthful. As you can hear in the video, the engines RPM seem to increase just before it shuts off. So I'm still investigating what I need to do. Hho is definitely a powerful fuel that harnessed and administered correctly into a combustion engine can work well.
@scottsmith6960
Жыл бұрын
Yep you need to be making high-quality HHO that is the biggest problem of everybody is doing an industry you're making more steam than high-quality done multimillion-dollar lab testing in California.
@sandortoth431
Жыл бұрын
HHO generátor
@srinipulsar9410
Жыл бұрын
Hello bro.. I m from india..I request you one piece make to me for 150cc petrol bike many times i make but not successful..Plz send me..Kindly rply..please
@yourworkshopmate372
Жыл бұрын
Hello Srini thanks for your comment. My attempt did not work and I'm still busy with another project that will hopefully work.
@KyzoFox
Жыл бұрын
First off, there is literally no reason to have the Intake OPEN. Not even 50% really. But you can use 50% intake. I suggest 75% intake choke. NOT ENOUGH BAR/pressure out of the HHO cell. You need HH+ and reduce as much pressure leakage as possible! Seal her off good, and make sure to at least 6 BAR/87 pound-force per square inch into the intake of nothing but pure hydrogen and oxygen. If you can achieve up to 6 bar you really don’t need the intake open from the airbox. In fact 6 bar to 8 bar max %100 choke is needed. Since you have 116 pound-force per square inch into the engine of nothing but hydrogen and oxygen mixture that was separated from the cell. 1. Pressurize. And seal as much as possible 2. 6 to 8 bar is needed for the engine to operate 3. Improve Hydrogen/oxygen separation efficiency and rate. Rich or too lean?. 1 bar - will not run 2 bar -will not run 3 bar - she might fire once or two (NOT ENOUGH ATMO PRESSURE!) 4 bar - %45 choke needed 5 bar -%65 choke needed 6 bar - %85-%90 choke needed 7bar - %90-%100 choke needed 8 bar - %100 choke needed.
Пікірлер: 281