This channel is the number one reason of why I’m getting a 3D printer (and some bags of concrete)
@evanbarnes9984
Ай бұрын
Dude I think my 3D printer might just be my single best purchase ever. It's a toss up between that and my paraglider. I know this won't be the experience of basically anyone else, but purchasing a 3D printer directly led to me getting an incredible new job that perfectly matches my interests and skills designing robotics toys. I was a teacher before that. Even if that doesn't happen, 3D printers are incredible tools. I used to think they were just for printing flexible dragons and iron man helmets, but they're quite possibly the single most versatile tool humans have ever created. This channel really showcases that fact. Just do yourself a favor and don't go cheap. There are a bunch of great mid range options out there now that are absolutely reliable workhorses. I know people love their Ender 3s for whatever reason, but I've never seen someone use one of those without immediately spending the price of the printer all over again on upgrades just to make it usable. Personally I love Prusa. They are more expensive, but we use them at work to prototype injection molded parts. They have thousands of hours of print time on them, and never once have we had to do repairs on them. I just keep the beds clean and the filament dry. Also they're FOSS/OSHW, and that kicks ass. We also have Bambus, and they are faster, but they're a bit less reliable. We've had some break down already. They also aren't as dimensionally accurate, but I think that won't matter as much for most use cases. Good luck on your printer adventures! It's a super fun world to get into.
@mid88night
Ай бұрын
Printers are only as good as the effort put into tuning them. I was given an old CR-10 mini that had issues. I took it apart, cleaned everything, reassembled, and tightened a few things that had been loose when I got it. Added a couple washers to space the z lead screw a bit better. The original build plate had issues on almost all of them, so I replaced that with a mirror tile for a few bucks. Replaced a few of the roller wheels that had flat spots in them. All total, I have about 20$ into "upgrades", and it prints as dimensionally accurate as I'll ever practically need after a few adjustments from calibration prints. Like press fit parts accurate. Mind you, the rollers were the only thing that needed replacement on a machine with several thousand hours on it. I still want a Ratrig or Voron at some point, but there's a reason people like their ender3's and clones of them. They're inexpensive, and after tuning, they just work.
@widget5963
Ай бұрын
@@mid88night I sometimes joke that I used to have an Ender 3, but now I have an Ender 3 frame with a completely different printer on it. But in comparison, I have a Magneto X now, and that thing required no tuning besides setting a bed mesh. I actually went through all the standard stuff and ended up pretty much the same as how it started. I think the Bambu printers generally have an experience like that too, although they're a bit more proprietary when they don't need to be. Personally I think 3d printing is getting into a pretty great place where pretty much anyone can just pick up a well tuned printer and immediately start printing with cheap engineering-grade materials like PETG-CF that are commonly only $25/kilo. Even PET-CF is getting down there and giving polycarbonate a run for its money.
@mid88night
Ай бұрын
@@widget5963 I want to build the CR-10 mini into a switchwire, so I get that sentiment haha. I don't NEED to, but I like modifying stuff, so there's that.
@DecDude84
Ай бұрын
an idea for a future build, a vibratory build table. You put future-future builds on the build table, it vibrates, and helps the concrete settle.
@jksjrgfpsjgr
Ай бұрын
hes using an hand sander for that.
@DD-DD-DD
Ай бұрын
We know. We watched the same video you did. He's talking about something completely different. For one, it would free up a hand.
@kalsaraan
Ай бұрын
You are quickly becoming one of my favorite design channels.
@MatchaMakesThings
Ай бұрын
Agreed!
@didms1526
Ай бұрын
was gonna comment this 4 videos ago
@themistoklisanastasiadis
Ай бұрын
you should consider with putting the lever gear behind the rack. that way you will push down on the lever instead of up, helping the press body not fail. awesome design too. maybe if the rack was a bit thicker, the forces would be greater. keep up the awesome work
@jasonthomashorn4794
Ай бұрын
Yup this. Both behind and wider rack. And awesome work, concrete as a filler is pretty novel. Chicken wire is easier to install but still provides some flex compared to something like grid wire. It probably doesn't make a difference now but if you get into the higher torsion it would.
@jasonthomashorn4794
Ай бұрын
Chopped fiber glass is a good filler. And even fiberglassing the outside would work wonders and relatively cheap
@munkysthrowpoop
Ай бұрын
That’s what I was thinking. Lifting upward seems really awkward to try and do while trying to keep the actual press on the table.
@thigo94
Ай бұрын
I was looking for this comment, had the exact same thought.
@MatchaMakesThings
Ай бұрын
Love the ending where you say "not everything makes sense to 3d print" It seems like such a no brainer to so many problems, but there are often better solutions.
@Okuhno
Ай бұрын
I love the acronym for the bathroom scale
@Extner4
Ай бұрын
The assembly with the minecraft music in the background and the tape peel after the concrete pour is always the best part.
@lsav1085
Ай бұрын
I can't believe that 3D printing and concrete ate not more widely combined! Great video, thanks!
@wildgophers91
Ай бұрын
Have you considered using a CSA based concrete? Here in the states we have "RapidSet" and they even sell additives to increase flow. You may also want to look into "plasticizers" for cement. They are additives that allow you to use less water. Then you can add stuff like glass fibers without ruining ratios.
@Rouverius
Ай бұрын
Just gonna say it: 98.9 is the new 100. Good on ya!👍
@blahblahblahblah2933
Ай бұрын
Nice video. With respect to the concrete, it seems like it's normally in tension and shear (while the press is pressing). Concrete is strongest in compression and worst in tension, so it seems like it'd be useful to post tension the concrete to preload the structure. That way it'd be in compression until you overcome the preload force of the post-tensioning. Granted it's moot since the concrete isn't the weak point of the press.
@grantprice613
Ай бұрын
Figured I'd compile some of the most useful tips on your hardening process: Use a higher alloy steel. These can be commonly found as "Grade 8", "12.9 metric" or "Alloy steel" bolts. These have more 'potential' for hardening than mild steels, which most cheap bolts will be made out of. Use a stirred ice/salt water quench instead of an oil quench. Oil quench is most common on tools where it is useful to trade a small amount of hardness for increased ductility. Your punch will not need ductility to resist impact, so try to make your quench as harsh as possible. If you can enclose your part while you are heating it, even between a few common bricks, you will find that you can reach orange-hot temperatures much easier. The camera can be deceiving, but it seems that what you reached was red-hot, which is below the heat treatment temperature for many grades of steel. Best of luck!
@DaveEtchells
Ай бұрын
Excellent tips, thanks for sharing! (I hadn’t thought of using 12.9 bolts as hardenable stock before. What’s their alloy, do you know?)
@RNMSC
Ай бұрын
If you are unable to locate higher grade iron for hardening, see Chris' (Clickspring) video on case hardening as an option. I'm not going to suggest it is better than using pieces of drill rod annealed for shaping and threading, then hardened and tempered, but it's better than not doing anything.
@homemadetools
Ай бұрын
Clever 3D printing idea. We shared this video on our homemade tool forum last week 😎
@joshbeaulieu7408
Ай бұрын
So at this rate I am going to furnish a shop using your designs. Thank you kindly. I just started printing with ABS to make myself a VORON, and after that I want to try making some of your tools. Thank you kindly for all your work.
@DaveEtchells
Ай бұрын
I was a bit surprised you didn’t make the rack and gear wider initially. It would have changed the svelte proportions, but I think the other components could have handled a good bit more force, especially with the threaded rods holding things together.
@ivolol
Ай бұрын
Bruh your tools are so cool. Could easily become reference standards of open source tool design. Use of concrete as reinforcing tool for plastic seems like a niche in the space. I wish you every success and hope you are inspired to create more awesome stuff like this, challenging what "3d printing can't do". Lord knows its entertaining to see happen. Great work
@BobWidlefish
Ай бұрын
I would love to see the limit of the other parts of the design by you iterating a few more times on the rack teeth until they’re not the failure point. In principle if you have high strength concrete shaped in relatively favorable triangles of the given inner dimensions providing a strong base for a lot of leverage. It’s not that surprising the thinnest plastic feature is the first to go, for sure. You are a great toolmaker and craftsman, excellent work!
@lowrads3653
Ай бұрын
Seems like a cross slide vise is the next item to turn the lathe into a mill.
@IdRatherBeMaking
Ай бұрын
Nice! I've made some crude concrete based machines but WOW, yours look better than mine! I have suggestions! You may want to consider is putting the rods through a single metal plate on both ends. The plate will increase the compression on the concrete, tie the allthread together, and give you a stronger part. The way it is now the nut only compresses the concrete directly under the washer and you could crack it in the space between the threaded rods. 2) I started 3d printing funnels to guide the concrete into the form, if you run tape around them it keeps the concrete out of the layer lines and makes it much easier to fill. 3) for the rack, consider tying in another geared rack on the back. More threads will give you a stronger column. SO CLOSE! :)
@bescobarca
Ай бұрын
Good video, just a tip, the press should tighten when lowering the lever on the front. This helps minimize twisting and make the force more vertical. I would move the gear behind
@lv_woodturner3899
Ай бұрын
Very interesting build. The metal in the bolts may be an alloy which cannot be hardened. In the US O1 drill rod is a common alloy which is normally sold in the annealed form and can be machined easily then hardened and tempered.
@GarpDesigns
Ай бұрын
I like all of your designs so far - just one question regarding the Arbor Press - is there a reason for lifting the handle up? as most all press's pull down on the handle so theirs no need to fix the base from moving and you should get a better feel of the force needed, I think your design would work better pulling down? Might be worth a try?.
@TinkerLynx
Ай бұрын
That's all I could think of while watching, it's the wrong way from any press I've used or even seen. Fixing that would make it stronger and nicer to use.
@johnhill5759
Ай бұрын
Graphene impregnated cement? Love the detailed design work you put in for no nonsense final builds
@leifhietala8074
Ай бұрын
Add an idler (or two, one on each side of the head) to transfer motion to another driving gear on the back side of the rack/plunger. That'll cut the load on the gears in half and should allow you to get to the magical 100kg target.
@user-cg3em4cw4f
Ай бұрын
Love to see the creative solutions you come up with for pushing 3d prints to their limits! I'm working on my own concrete CNC lathe at the moment since you gave me the idea. Can't wait to see what you'll produce next! I did however forget to sift the aggregate out of which was a bit of an error on my part as stuff did not flow nearly as well.
@Mkz0r
Ай бұрын
3d printed one looks better than bought online !!!
@RNMSC
Ай бұрын
Have you considered replacing the rack with a course thread 15-20 mm bolt with 3d printed guides to square the profile up through the press? You are after all, already using an M8 bolt or all thread to compress the layers in the rack, You would need to change the helical gears angle some, and could include extending the threading shape across the square profile the bolt is in to hopefully reduce the stress on the driving helical gears.
@CruzMonrreal
Ай бұрын
It's so close! You could totally reach it if you change up the gears and rack. Increase the pressure angle for thicker teeth, a larger module fir physically larger teeth, or changing the material for something more durable
@CWModelling
Ай бұрын
I found your channel a while ago and I must say that I personally have no use for which to copy your designs BUT I am fascinated by the whole process of what you make.....Garden shed engineering at its finest 👍
@Aaku13
Ай бұрын
love the vids man, so well produced for such a new channel. keep it up man!
@segment932
Ай бұрын
Tip. Try to print every thing at a 45 degree angle. Prints often get much harder that way because each layer get a larger area to adhere to the previous layer. Check Slant 3D he talks much about that.
@lawabidingcitizen5153
Ай бұрын
To harden the steel you need to get hardenable steel, 12.9 bolts might work
@andymuzzo8568
Ай бұрын
Don’t try to harden 12.9 anymore you make it to brittle
@petergamache5368
Ай бұрын
The cheapest 1 ton arbor press I can find in the US is at Harbor Freight, for $70. Given that they regularly have coupons that give you 20% off of a single item, if you're patient, you could get it for under $60. The frustration factor involved in the "DIY arbor press" seems to make that purchase an easy decision. :)
@The3DPrintingGrandad
Ай бұрын
Your videos do inspire me.
@802Garage
Ай бұрын
Not something I had considered, but very cool!
@Yy-ig6fm
Ай бұрын
The steel you used for the punch may have been austenitic stainless, which isn't hardenable. It would be better to use high carbon non-stainless steel because it's easier to harden without weakening it. There are lots of stainless steels that will harden up too but they usually have a more involved heat treating process with holding times and are less tolerant of mistakes. For your application you can just hit some carbon steel with a blow torch to a red glow. (not yellow, not orange) and quench in oil. Then if you feel like it you can heat treat at about 175c in your oven for a couple hours to make it less brittle. This will drop the hardness obtained after the quench a little tiny bit, but this will give the part a lot more strength compared to using the steel without doing so.
@jimysk8er
Ай бұрын
you have a partial tooth failure because the forces are pushing the rack and pinion apart. the more you push down on the bar the more force is acting against you in friction and in deflection and the deflection is also decreasing your grip. all to say that you made a press with a compliance based cap which would be great if you needed to ensure that can't exert more that 100lbs on a part that is more expensive then the press
@E50creative
Ай бұрын
NIce work on the 3d renderings quality work i can see you easily growing to 2m plus subs at this rate your a natural bro nice work nice work
@makegrowlabrepeat
Ай бұрын
Chopped fiberglass(about 1cm) works well for "rebar" in these types of projects
@D-One
Ай бұрын
A bit crazy but also very interesting, it looks like with just a couple of cheap metal parts like rack and pinion this would actually be very capable. Would love to see it tested.
@rsilvers129
Ай бұрын
You can anneal the rack to make it stronger. You can also try PLA Plus.
@kyleisah
Ай бұрын
I think you might have this backwards. The pinion gear on the shaft from the handle needs to sit behind the rack, with the rack gearing being on the back of the rack. That way, downward movement of the handle translates to downward movement of the rack, which should reverse the load direction the frame is seeing. At least, that seems correct in my mind. The rack/pinion teeth will still be the weakest part, but I’m curious what moving the pinion behind the rack would do. Loved watching this though!
@kyleisah
Ай бұрын
Yeah, with every arbor press I’ve ever used, the gearing on the rack is on the back, and the handle/pinion shaft and gear sit just behind the rack, which translates the movement that way.
@Roobotics
Ай бұрын
Long time enjoyer of your videos, thank you so much for this series. I think I came up with a very interesting idea for a limitation I can tell you fought with. For a press there is a balance between parts accessibility, and the presses core strength. But what if you could have both options depending how it was configured at use? Basically to get down to it, a nice chunky bolt that can be installed right behind the press arbor or at set increments of depth. If increments were used, you could even leave multiple installed all in a row for added tensile strength, until a part dictates a needed clearance. With this idea a lot of the forces generated would be shunted into the metal instead of flexing the concrete and mesh structure (simply having one installed, would turn that force back into a compression load.) Also I wonder if your gears would be more robust in Nylon, ASA, or maybe even PETG.
@tannergilliland6105
Ай бұрын
The Minecraft music goes surprisingly well with this.
@Dangineering
Ай бұрын
I have never been so blown away by a channel before. Another amazing tool.
@aidandavy4303
Ай бұрын
Loving the increase in uploads probably my biggest inspiration so far to start designing parts myself and get off thingiverse :)
@3dpartner
Ай бұрын
you should start to think out of the box regarding position your prints, the base should be much more stable when you place it at the corner at the back.
@BadgerRobot
Ай бұрын
To harden steel, it needs a higher content than standar bolts tend to have.
@TheVgonman
Ай бұрын
Love the SVU comments! 😀
@doxielain2231
Ай бұрын
Now you can make a heated tip to insert threaded inserts
@cactus7027
Ай бұрын
Another amazingly crafted tool and design. Thank you for doing what you do!
@notyouraveragegoldenpotato
Ай бұрын
Spare car scissor jack, couple metal scraps, cheap welder. Bam, easy 1.5 ton press (or whatever tonnage you want just swap out the acissor jack😂 i use it every day
@funcorporatelife2177
Ай бұрын
This is exactly why i want to build my website
@mitchellquinn
Ай бұрын
IED. Improvised Experimentation Device. Golf clap. Well played sir, well played indeed. I dare say that I shall yoink that at some point.
@simonebiuso3098
Ай бұрын
Next make a mini 3dprinted cement mixer!
@moccaloto
Ай бұрын
I've been waiting for you to make one of these. Well done 👍
@Defeshh
Ай бұрын
I love this channel
@jlrebor2626
Ай бұрын
to put a complaint, the handle works opposite of what i would expect and males less sense if you ask me, idk if this was made bcs of some difficulty, but pushing up to push down feels wrong af, and i feel like it makes it less stable, as i said idk if there was any problem, but it was a thing of changing where the rack and the gear is, just turning them around would have give you a down movement for a down push, like a drill press, if this was by choice or preference then cant say anything about it
@TheJacklwilliams
Ай бұрын
Ok Chris, ive been following for some time. Enjoy your design choices and skills immensely. I have to ask, watching you spray paint, do you have a couple hundred pounds of orange filament? Aka why dont you simply print the black pieces with black filament? Killin me. Everything else you do makes complete sense to me. This one, boggles my mind… lol, thanks for sharing all your work!
@bear2c
Ай бұрын
How about adding a heating system to the end, so it can press heat inserts?
@mattylarkspur9858
Ай бұрын
that was my first thought too!
@KnexJunkie
Ай бұрын
yeah buying one but whats the fun of that? nice project. maybe at a serten point it might be worth 3D printing it compared to a store bought one. Stil depending on what you need to Press into stuf this could maybe be a better choice.
@snapo1750
Ай бұрын
May you allow me the question: Did you ever consider using a geopolymer instead of cement? (Waterglass , Alkali activation, Metakaolin) Alkali activation lye , burned white wood ash Metakaolin (calcinated kaolinit) the mixture in the right way would create granite and should be much better than cement
@ransombot
Ай бұрын
I was going to say use hardware cloth but looks like you did.. You ever try fiber additives for concrete? Should add even more strength to it with minimal investment. It'd be fun to see your press test different samples of its self sorta like C&C kitchen does with 3d prints. Not sure if it interests you but there's some microwave casting videos on youtube that you could probably cast the rack and pinion in bronze or aluminum and pass your 100lbl goal. Not much cost in getting into casting that way as you can get ones with broken lights and carousels things from family, ebay, or dumpsters fairly cheep.
@gustavo76016
Ай бұрын
maybe you could try with a Fly Press Head? I think a Screw could withstand more force than 3D printed gears
@king_james_official
Ай бұрын
9:10 cool plug vro
@Ernzt8
Ай бұрын
Great experiment!
@julias-shed
Ай бұрын
Really good project again 😀 wonder if a different helix angle would be stronger?
@Fyreye
Ай бұрын
Was just thinking of getting an arbor press and was wondering if you had done any experiments in that arena 😆
@Amin-js4su
Ай бұрын
RAAHHHH CHRIS BORGE UPLOAD
@chrisgill5692
Ай бұрын
Great video. Why do you have it geared/orientated to lift & push, rather than pull down the handle?
@wildgophers91
Ай бұрын
My gut reaction to the title: "But a small arbor press is so _cheap_ and easy to buy, why would you go through all the hassle of making one?" Excited to see what the authors conclusion is.
@tythetasmaniantiger7
Ай бұрын
Really impressive
@DeverSonic
Ай бұрын
When the Minecraft music comes on you know chris borge is about to fucking cooook
@BudoReflex
Ай бұрын
Magnificent
@Donnie-uw5kz
Ай бұрын
i say make the gears out of PETG and to more wall layers or make it solid, based on the color of material it looks like your using PLA
@creative_stwb1336
Ай бұрын
Future idears. For more force try and build a flypress with a lead screw from a typical 3d printer
@Rollmops94
Ай бұрын
Should be pretty simple and cheap to get metal gears. I really wonder what ways there are to achieve higher pressures. What are design techniques used in real presses?
@rickharriss
Ай бұрын
Yo8ur bolt is mild steel. Not enough carbon to harden. you could however case harden it. Look up the process.
@robonator2945
3 күн бұрын
it took me longer than I'd like to admit for my brain to realize I shouldn't have been hearing minecraft music. I mean I heard the music and recognized it was minecraft music in like 5 seconds, but it took like 5 minutes for me to realize I wasn't playing minecraft, nor was it open in the background.
@sveinarsandvin6418
Ай бұрын
Wonderful. Teach us more.
@jbrownson
Ай бұрын
Excellent thumbnail
@peterkiss1204
Ай бұрын
Let me get in my smart pants and give you some advice. I would print the rack on its side the teeth looking sideways and it would be much stronger. You can force the layers together with some small bolts normal to the layers planes. (4-5 pcs on both sides of the long bolt along the whole length must be enough) PETG rack and pinion would be more tough and have less friction than PLA parts.
@75keg75
Ай бұрын
Chicken wire can be moulded into shape and will reinforce the concrete.
@LaGrangeDeSteepy
Ай бұрын
Incredible you did it ! :D
@HoffmanTactical
Күн бұрын
Yes.
@KyleJamieson
Ай бұрын
"Not everything makes sense to 3d print" - please don't let spouses anywhere hear this...
@daysejones968
Ай бұрын
how to be a good ytber: part 1- have a cool accent. part 2- build things. part 3- profit
@OmegaGamingNetwork
Ай бұрын
That feel when you really want to make something, but are fighting with the knowledge that you have 3 of them already that you don't use.
@bernarrcoletta7419
Ай бұрын
How did you know I was looking through your channel , last night, looking for an arbor press?
@ProtonOne11
Ай бұрын
Cool idea, but i'll keep my eye out for a used one that has a bit more durability. Of course the hardening of the pointy tool does not work if it's the wrong type of steel. You need a high carbon steel, or introuduce more carbon to it in the heating process. Screws are usually not made from high carbon tool steel, because you want them to be ductile and not shatter quickly under tensile load.
@RvnKnight
Ай бұрын
"Not everything makes sense to 3D print" I have to disagree in part. If you are wanting to learn how to design your own parts and tools, having a physical model of it is useful so you can understand the methods behind why some designs work and some fail. You also have the case where it may be faster and cheaper to print and do lost PLA casting than ordering the same object. (Aside: That may be something to play around with if you haven't already.) Overall, great video and content, you gained my sub from it.
@i-mine-clay562
Ай бұрын
the minecraft music in the backgrond was triping me up thinging my game was running
@gabelyons8426
Ай бұрын
This is very interesting to stress test 3d prints but like, what would you use a 100 kg arbour press for? Just like step on the thing you are pressing?😂
@littlehills739
Ай бұрын
two gears to the pinion ? to 1 gear to the handle ? and if u export ur cad work to dfx u might as well get it laser cut thinking along the lines of if you ebay parts like long bolts then theres no difference in ordering laser cut steel plates
@lowrads3653
Ай бұрын
Might as well get some doming tooling for buttons or other minor planishing activity.
@lowrads3653
Ай бұрын
These kinds of presses are also useful for putting watch cases back together. You tend to need a bunch of different sized plastic dies to keep the glass from being stressed.
@Tarh
Ай бұрын
I have found that concrete makes PLA very brittle. I can't use a mold printed in PLA more than once, but I have no problem with the mold printed in ASA. Have you noticed that too?
@ipiqqyfpv
Ай бұрын
ok subscribed because you used stall for music, oh also nice video...
@janvrabec3401
Ай бұрын
YOU HAVE A LATHE NOW??? WHAT WAIT WHAT
@mikoaj2323
Ай бұрын
Maybe double helix gears?
@magicshon
Ай бұрын
Just recently i looked at all the 3D print arbor press models i could find with the idea of printing one to rivet kydex for knife sheaths. I was wondering if they would possibly hold up even at 100% filament and seeing that yours even with concrete fails at 100kg i am pretty confident the others wouldnt hold up either. I like the idea of two screws instead of a square axel, i will remember that for when the need arises. But what did they connect to? The black part has to still go through the red one on some axel and into the middle gear, where i would expect a square to go through? Lastly do you design your own gears or are those automated? Would maybe larger teeth hold up better? Or possibly teeth that have a longer straight section on their tips.
@gruvinnz
Ай бұрын
Why do you have the wrack gear at the front, such that the lever works against the applied force, needing to be lifted up, rather than down at the hold point?
@Fyreye
Ай бұрын
came to the comments section to ask this same question! I wonder if changing the direction of the lever's force would add that extra little oomph to get the clean 100, since you wouldn't be applying torque in the opposite direction of the main force
Пікірлер: 150