essa ceramica foi instalada 1 dia antes da postagem do vídeo!
como todos inscritos já sabem eu início a colocação da canjiquinha começando pelo estudo da paginação!
colocando as pedras no chão e medindo a altura da parede.
depois de ter a medida da parede ,é a medida das pedras, é só bater o nível!!
usei o novel a laser para Bayer o nível rapidamente!!
nível batido ,coloquei massa na parede e depois fixei a régua de alumínio apoiar as peças.
Para escorar a regue uso pedaços de ceramica com as médias aproximadas de 3x20 cm .
regua apoiada damos início a colocação trazendo Cordões para cima e iniciando a colocação da segunda pedra de baixo para cima ,sempre passando massa na parede e atrás da peça para dar Mais aderência!!
finalizando a colocaco devemos rejuntar a canjiquinha.
Antes de rejuntar eu uso o estilete e bucha verde para limpeza das pedras sujas pela argamassa !!
a ceramica canjiquinha limpa é só iniciar a colocação!!
Para reju tar eu uso u. pedaço de tatame com tamanho aproximado de 7x12 cm.
aplicando todo o rejunte.
qual quer dúvida eu ensino o passo a passo no link abaixo :
• REJUNTE Limpeza seca ...
depois de rejuntado é só limpar com a bucha umida e está terminado !!!
espero que gostem do vídeo galera,um abraço a Deus abençoe a todos !
Dica de colocação para iniciantes
Utilize essas ferramentas para colocar piso !!
Faça você mesmo que este macete é simples
Desempenadeira dentada
Martelo de borracha
Régua de alumínio
Riscador manual
Serra mármore makita
Furadeira makita
Lápis de carpinteiro
Linha de pedreiro
Colher de pedreiro
Espaçador cortag
Caixa de massa
Extensão com fio de 2,5 mm paralelo
Prego de aço
Chave de fenda
Alicate de pressão
Esquadro
Óculos de proteção
Máscara
Protetor de ouvido
Luva de borracha linha de marcação
Mangueira de nível
Nível bola
Prumo
Niver A laser
this ceramic was installed 1 day before the video was posted!
as everyone registered already knows, I start putting the canjiquinha on starting with the study of the pagination!
placing the stones on the ground and measuring the height of the wall.
after having the measure of the wall, is the measure of the stones, just hit the level!!
I used the laser novel to Bayer the level quickly!!
beaten level, I put putty on the wall and then fixed the aluminum ruler to support the pieces.
To support the watering I use pieces of ceramic with the approximate averages of 3x20 cm.
ruler supported we start the placement bringing Cordões up and starting the placement of the second stone from the bottom to the top, always putting mass on the wall and behind the piece to give More grip!!
finishing the placement we must add the canjiquinha.
Before grouting I use the green stylus and sponge to clean the stones dirty by the mortar!!
the clean canjiquinha ceramic is just starting to be placed!!
To dejure I use u. piece of tatami with approximate size of 7x12 cm.
applying all the grout.
any doubts I teach you step by step in the link below:
• REJUNTE Limpeza seca ...
after grouting, just clean with the wet bushing and it's over!!!
I hope you like the video guys, a hug to God bless you all!
Placement tip for beginners
Use these tools to lay the floor !!
Do it yourself this trick is simple
Toothed trowel
Rubber hammer
aluminum ruler
hand scriber
Makita marble saw
Makita drill
carpenter's pencil
mason line
Trowel
Cutting spacer
dough box
Extension with 2.5mm parallel wire
steel nail
Screwdriver
Grip pliers
square
Protective goggles
Mask
Ear protector
Line marking rubber glove
level hose
ball level
Bob
Laser Niver
Негізгі бет CANJIQUINHA NA SALA COLOCAÇÃO CONCLUIDA NO MORUMBI,DECORACAO DE SALA
Пікірлер: 10