a master at work, lovely job ,can't wait for the next one
@TheHumblePaintSprayer333
Ай бұрын
Thank you very much!
@Мишутка-ю5э
18 күн бұрын
Hi i am from Russia Good and itresting
@TheHumblePaintSprayer333
18 күн бұрын
Hi thank you for taking the time to watch my videos
@Мишутка-ю5э
17 күн бұрын
Ok
@JohnWD40TC02
Ай бұрын
Hi Jason, fantastic result on the blend and the trusty 1.3CC did the business on the clearcoat, I haven't used any glue pulling gear but have a look at the Keco gear mate I've seen quite a few on here like Wayne and Tony using it, their glues are fantastic and one demo I saw they actually moved a car with just a small pad glued to it, it seems like the trick is all in the temps mate if you have the glue and the panel at the right temp then it sticks 10 times better. There are loads of videos on here with people like I mentioned about using them and even demos by the manufactures showing how it's used👌👍
@TheHumblePaintSprayer333
Ай бұрын
Thank you mate really appreciate the recommendation i will defintly look in to it 👍
@vincetaylor944
Ай бұрын
Great job Jason, as always. An invisible blow-in , you never know what you’ll find I suppose until you start prepping it ? Cheers mate, Vince.
@TheHumblePaintSprayer333
Ай бұрын
Cheers Vince
@theessexhunter1305
Ай бұрын
Very nice, little dents need just as much detail as bigger ones. was you folding the tape in half over your knee to make a soft edge..old school trick
@juhis6969
Ай бұрын
Great job man...again🔥💯💯
@davecooke914
Ай бұрын
Top job Jason as always 👍👍
@Ulr149tw21
Ай бұрын
wonderful job as usual keep up the good work thanks again
@TheHumblePaintSprayer333
Ай бұрын
Thanks again!
@billsheehy1660
Ай бұрын
Awesome job!
@TheHumblePaintSprayer333
Ай бұрын
Thank you! Cheers!
@FK-zr9fn
Ай бұрын
Jason have you got a Rat in the garage or is it up your backside well it ain’t there anymore. Great video and great job as usual 👍
@TheHumblePaintSprayer333
Ай бұрын
👀😂Not sure what you mean but .... there's a rat in me kitchen, what am i gonna do 👍
@JohnSmith-it6hj
Ай бұрын
You're not letting that glue get hot enough mate. Took me ages to figure that out. needs to be really hot and runny and left on the panel for 35 seconds at least before pulling.
@TheHumblePaintSprayer333
Ай бұрын
Thanks mate really appreciate that, do you know what’s the best glue to buy, seen different colours but not sure what the grades are if any or if there’s different glues for different purposes
@JohnSmith-it6hj
Ай бұрын
@@TheHumblePaintSprayer333 i use the red stuff, is a good all rounder, they'll all work for fairly shallow dents, the trick is to degrease the dent and get the glue as hot as you can, leave the glue gun on for about 15 minutes to let that nozzle really heat up, i guarantee once you try really hot glue with a decent cool down time, you'll pulling dents like carrots!
@TheHumblePaintSprayer333
Ай бұрын
@@JohnSmith-it6hj thank you mate i didnt even think of the glue temp, i might get a better quality glue gun as mine seams well cheap 👍
@ANDY-we7mr
Ай бұрын
HI JAY GOOD VIDEO THAT DID YOU SAND THAT PRIMER DOWN MATE AND THAT STUFF WHAT YOU FIRST PUT ON IS THAT MIPA BLEND ADDITIVE THEN BASE AND CLEAR COAT JAY WHEN I GOME TO DO MY FORD FOCUS MK3 TITANIUM X FRONT BONNET AND BUMPER MATE OK TO DA SANDER THE BONNET WITH 320 GRIT AND THEN 800 GRIT SAME WITH THE BUMPER JAY OR WHAT WOULD YOU RECOMMEND MATE 😊
@TheHumblePaintSprayer333
Ай бұрын
Cheers Andy, yes it was the blender coat, if you sand with 320 grit first you would need to got to 500 grit next then i would 600 grit to finish if your putting base coat on it, 800 grit would be ok for clear coat
@andrewodonoghue8666
Ай бұрын
Nice job ! What was the first coat after priming ? Thanks keep them coming ..
@TheHumblePaintSprayer333
Ай бұрын
Thanks it was the blender coat first
@AlanMcCormack-oe1oo
Ай бұрын
jason try keco for glue pulling they are world leaders and have uk addresses
@TheHumblePaintSprayer333
Ай бұрын
I will check them out thank you
@nicholasviney5975
Ай бұрын
Perhaps when you got a quiet time it might pay to see if there is a PDR course you can take.
@TheHumblePaintSprayer333
Ай бұрын
Yes i have thought about that it would be worth it i think, i definitely need some training 😂👍
@johnbentley9241
Ай бұрын
Could I ask about the palm sander that you use - what is the make and stroke please?
@TheHumblePaintSprayer333
Ай бұрын
@@johnbentley9241 it’s a mirka deros 650 electric with a 5mm orbit
Пікірлер: 33