Carburetor Tuning To Get Ideal Average / Mileage
Carburetor Parts Detail
Float Chamber:
The fuel level is controlled by the fuel floats and the float valve. The floats are hollow and are made up of a material that will float on fuel. The part of the float processes against the float valve, called the needle and seat. Most of the times the float valve needle is bendable so that you can adjust the fuel in the float bowl/ chamber. All plastic floats are not adjustable.
Pilot Jet:
The idle jet controls the idle, this screw leans or riches the fuel mixture for a smooth idle and up on one quarter throttle. They affect the mixture as long as the vacuum in the venture is over them. As the throttle further opens, the vacuum moves the needle jet and jet needle.
Throttle Valve:
The throttle valve is the big slide that opens and closes the throttle, it has a bevel angle cut in one side of the big round slide, towards the air cleaner.
Jet Needle:
This needle rides the throttle slide that goes into the needle jet. The jet needle controls the mixture from 30-80% open throttle. It will come in different sized tapers. The top end of the jet needle has grooves cut in it, usually five, you can move the clip up to lean the mixture or down the needle to increase the richness.
Main Jet:
This controls the mixture from 60%-100% open throttle.
Proper Tuning Method:
Warm up the engine well before you begin the process; take the bike for a good 10-15 minute spin. Do not leave the engine under idle for 10-15 minutes because the results won’t be very effective. Now you will have to look for the air fuel screws. You will notice that there will be two screws, one for the idling rpm and the other for the air fuel mixture.
Set the idle speed adjusting screw, clockwise to increase the rpm and anticlockwise to decrease the rpm. The optimum idle range can vary from 900-1200 rpms. Now adjust the idle screw to a mixture by turning the screw so that the engine runs poorly. Then turn the idle screw clockwise until the engine begins to grumble, keeping the positions in the mind. Set the idle mixture screw halfway to obtain the best idling position. Now the engine will run under a lean mixture.
Various stages can be noted by looking into the tachometer or by just listening to the engine's sound. The RPM at this state will not be steady. Start turning the fuel screw 1/8th turn at a time. The RPM will slowly increase and become steady. In fewer than 5 full turns, the RPM will become constant. After this point screwing must be avoided, this can be the best setting for the engine. Trying to screw more the mixture will become rich and the fuel efficiency will start going down. Repeat the process for best results. When the engine is properly tuned crisp throttle response and decent engine sound can be observed.
If you really want to get the best results, try taking the motorcycle for a spin after every adjustment you make, this way you can choose the most optimum performance settings for your engine.
Carburetor Tuning To Get 40 KMPL Average / Mileage
Carburetor Tuning To Get 40 KMPL Average / Mileage
Carburetor Tuning To Get 40 KMPL Average / Mileage
Carburetor Tuning To Get 40 KMPL Average / MileageCarburetor Tuning To Get 40 KMPL Average / MileageCarburetor Tuning To Get 40 KMPL Average / MileageCarburetor Tuning To Get 40 KMPL Average / Mileage
Carburetor Tuning To Get 40 KMPL Average / Mileage
Carburetor Tuning To Get 40 KMPL Average / Mileage
Carburetor Tuning To Get 40 KMPL Average / MileageCarburetor Tuning To Get 40 KMPL Average / MileageCarburetor Tuning To Get 40 KMPL Average / MileageCarburetor Tuning To Get 40 KMPL Average / Mileagev
Carburetor Tuning To Get 40 KMPL Average / Mileage
Don't Forget to LIKE, SUBSCRIBE, SHARE & COMMENT
This video will really help you.
If you need any suggestion or help, Comment me on comment session and i will reply you as soon as possible.
Thumps up if you like my video.
Suggest me the Video and i will make the video for you all.
SUBSCRIBE NOW FOR MORE VIDEOS
Thank You for Watching My Videos
"Ride like a Beast"
~-~~-~~~-~~-~
Please watch: "Royal Enfield Full Service At HOME - PART 1"
• Royal Enfield Full Ser...
~-~~-~~~-~~-~
Негізгі бет Carburetor Tuning To Get 40 KMPL Average / Mileage
Пікірлер: 197