Nice to see the lead come out all in one piece. Tackling the same job today. Thanks for the video!
@desertgecko4549
4 жыл бұрын
Six years after you uploaded this video and still helping DIYers. Thanks! I was surprised to see the hub under the house, thought I had only a section of cast iron to deal with. Now I know how to fix it.
@romankilun1527
3 жыл бұрын
Did this same job yesterday. mine was very tight. I could not get it to fit until (1) I got the rubber donut hot with some hot water and (2) to the PVC in the freezer to shrink it slightly. Once it was hot and a little lube, it went in. Beveling the lip is must. Hope this helps someone else.
@TheAlpine49
6 жыл бұрын
THANK YOU!! I needed help desperately because I had the exact same problem you had. You helped me solve it! You are the man!
@FireEater
9 жыл бұрын
Beats cutting the hub off. Thanks 🚽 from NY.
@charger440
5 жыл бұрын
Thanks a lot my friend,you have saved me a lots of money and it’s the easiest and the cheapest way to go!
@SCHNEIDER2862
6 жыл бұрын
Thank God! Somebody finally using the proper connection (Fernco cast iron to pvc/abs Donut). GOOD JOB! Next time use a little dish soap as a lube; way easier!
@stevensobba1785
4 жыл бұрын
Mark Schneider What if the cast iron is horizontal in the the ceiling joists, two story, will that fernco work ? From a tub ,shower ...pvc to cast iron ?
@StONEMASON23
3 жыл бұрын
@@stevensobba1785 most def.these vent pipes/grey water pipes dont hold pressure
@smirkinatu5512
3 ай бұрын
Thank you for recording and posting this valuable educational video.
@whasumara73
6 жыл бұрын
Thank you MrEnergyFree. I appreciate the instruction.
@mcasiano
3 жыл бұрын
Thank you for this, was exactly what I was looking to do. Great video!
@OrganicGreens
3 жыл бұрын
Thank you so much Joel you saved me like 1000 dollars.
@vickicocosolo2099
6 жыл бұрын
Helpful video! Thank you for posting this!
@Lugenfabrik
2 жыл бұрын
Thank you for the clear explanation and demonstration buddy.
@rict.4938
Жыл бұрын
Thanks bro! This was the video I've been looking for, for weeks. Awesome! Thank you for making this
@ted458
10 ай бұрын
There is a special adapter called a "hub adapter" or a "cast-iron pipe adapter" that is made to use with the rubber Fernco gasket ("donut"). It goes on the end of the PVC pipe to make it easier to get the pipe properly seated down into the hub and Fernco gasket. (Also a little dish soap or silicone spray would help as several other people suggested!)
@johnschutt9187
3 жыл бұрын
Very nice work. Very helpful video. THANK YOU!
@billmorley3530
5 жыл бұрын
Great video--just what I needed!
@kittshausman6191
4 жыл бұрын
Thank you so much. I can finish my job tomorrow
@mike7gerald
7 жыл бұрын
A helpful video! That rubber donut is called a 'service weight gasket'.
@LAHarder7
4 жыл бұрын
That name implies its held in place by gravity. Can these also be used in a horizontal connection?
@catwinterberry7265
2 жыл бұрын
Service Weight (SV) refers to the thickness of the cast iron. Extra Heavy Weight (XH) is the other kind. They can be used on the horizontal, but the pipe should probably be well supported.
@TEBCO123
Жыл бұрын
nice job joel.
@kyletimmerman7329
3 жыл бұрын
Thank u. The help is much appreciated
@fascinatingfambam4984
4 жыл бұрын
Very helpful. Thanks for the video
@frankie2234
10 жыл бұрын
I have found that liquid dish soap mixed with water makes a nice slippery lubricant to help slip pipes into the rubber boots and such.
@workmansworkshop6772
6 жыл бұрын
Thank you!
@Lilmiket1000
5 жыл бұрын
Thank you. everyone keeps saying lube it. but when you think of lube you think of grease. which is not the best thing to use with rubber. never know what reactions it might have long term. best to just use plain old soap and water to be safe.
@ryanhoeven7826
3 жыл бұрын
Do they make a bushing to go inside a cast iron spigot, and to reduce to pvc spigot?
@vernonroach918
6 жыл бұрын
Arm and hammer plumbing...My favorite kind....Good filming.
@jnunez1203
6 жыл бұрын
Vernon Roach 😂😂😂😂
@StONEMASON23
3 жыл бұрын
beat it home baby
@chucksguitarshop
8 жыл бұрын
Very good. Thank you
@amyhilley4595
9 жыл бұрын
Hey. Good Video! Question? Would it be alright to use a clear silicone for lubricant?I have a metal pipe that has a small hole in it going into the cast iron.I can get to it through the closet,but its kind of tight & thought using silicone would help slide it in easier.
@StONEMASON23
3 жыл бұрын
explain? you can patch a pinhole with epoxy..the pipe is not holding pressure
@h2bbuilt
2 жыл бұрын
Did you have to put any primer or glue?
@stevecunningham3475
5 жыл бұрын
Soapy water or any soap will make it slide on very easy.
@Ivan-Torres-1979
5 жыл бұрын
Meet my little friend,good video champ.
@coffeeisthepathtovictory1290
5 жыл бұрын
Meet my little friend: Shows rubber donut for hub =))
@ArcheryRuleZ
6 жыл бұрын
Thanks!
@TheNimshew
5 жыл бұрын
What you have is a service weight compression gasket. It will work, but Fernco makes a donut for that application. Soapy water helps and put a piece of wood on that pipe and smack it hard with a heavy sledge to drive it home.
@DarlaAngl
9 жыл бұрын
Heat your gaskets with a space heater inside a box or with the cab heater in your vehicle
@romankilun1527
3 жыл бұрын
Or dunk it in some hot water
@normanfields6371
5 жыл бұрын
Use 4 in sda fitting with plumbing grease goes right in then connect to the fitting VERY easy.
@J.ArturoMartinez
4 жыл бұрын
This video saved my life.
@mikemarino3635
8 жыл бұрын
just lean on it and apply pressure . But some water or alittle petroleum jelly on the end of the pipe.. It will push right in.
@donluedetmoonsone9573
2 жыл бұрын
Thank you my friend
@thegoodenoughangler
4 жыл бұрын
I have the same question as a couple other guys. How did you get the original cast iron pipe out of that hub?
@MrEnergyFree
4 жыл бұрын
Torch and flat head screwdriver piking on the lead until all gone. Melting lead and pulling out with the screwdriver.
@thegoodenoughangler
4 жыл бұрын
@@MrEnergyFree Thank you!
@jaro2450m
5 жыл бұрын
Palmolive Dish Soap Little on the rubber ring and going nice and smooth
@coffeeisthepathtovictory1290
5 жыл бұрын
I’ll give the palm olive and water a shot thanks youtube comment guy 👍
@gringojoe1
5 ай бұрын
Next time try putting a little liquid soap around the PVC
@midwest4416
3 жыл бұрын
Greeting from 2021. Think I'm giving your method a try. Even the Fernco directions state to put donut on PVC and drive gasket into hub (What a Bear -and still an inch I can't get to seat. -thx
@leoandsonpaintings3087
3 жыл бұрын
Buen trabajo
@tommyt1556
10 ай бұрын
Status update? Any leaks 9 years later? Any problems you had to address? If so, what were they? Obrigado and Gracias!
@johnsmith-sw7ii
4 жыл бұрын
A little dish soap on the PVC will help it slip into the rubber seal
@masterman83
5 жыл бұрын
You should of used duck butter. It’s the best this for a cast to pvc boot adapter.
@stormbytes
5 жыл бұрын
How did you manage to get the old cast iron pipe out of the hub?
@trangwuong7689
2 жыл бұрын
Dig out the lead and oakum with a flat-head.
@trangwuong7689
2 жыл бұрын
Dig out the lead and oakum with a flat-head.
@georgeplhak
9 жыл бұрын
Very helpful video - thank you. I cannot find the gasket rubber that you are using. Can you give me a manufacturer and part number so that my local shop can order it for me. I went to four plumbing places and they don't have a gasket like that. I need exactly the size that you are using 4" iron hub to 3" plastic pipe. Thanks!
@MrEnergyFree
9 жыл бұрын
I got the gasket from my local plumbing supply. Not sure aboutthe part number.
@georgeplhak
9 жыл бұрын
I am in Canada and HD does not sell it here. I had it ordered and paid four times what HD in the US charges
@joealfaro1243
6 жыл бұрын
Amazon
@scottyclontz8972
5 жыл бұрын
Check with mission rubber
@tigerbody1
9 жыл бұрын
Thanks for the video. Is there some reason you are using PVC rather than ABS?
@wolfattack402000
8 жыл бұрын
+patrick donegan Some areas of the country, like here in Ohio, pvc is preferred. I do know that abs solvent cements much easier with a single step. PVC requires a 3 step process - clean, prime, cement.
@tigerbody1
8 жыл бұрын
you don't have to clean abs?
@mitchelldillinger243
6 жыл бұрын
patrick donegan ABS has been recalled by nibco and other manufacturers in almost every U.S. state due to shrinkage. Just head down to your locally mobile home park and try to find an ABS joint without drip stains. It's just for sump pumps now. Good idea using recycled material, but too much shrinkage long term.
@Lilmiket1000
5 жыл бұрын
everyone and everything uses pvc here in charlotte. I didn't even know abs pipe existed until I saw a video on here of someone replacing it. I was like huh black pvc lol
@aaronbennett8364
2 ай бұрын
PVC is the code requirement where I life. We are no longer allowed to use ABS for interior drain pipes like this.
@allanpennington
6 жыл бұрын
I have a similar situation but the cast iron pipe I want to remove from the clay hub is cemented in. Can I safely use a cold chisel to chip the concrete away from around the cast iron pipe to remove it? Or am I likely to break the clay pipe hub?
@rickfreeman1101
4 жыл бұрын
If he had put a little soap around the pvc pipe, it goes in smoother and seals well.
@joemama1151
9 жыл бұрын
Dont use a hammer. lub it and push it in by hand. rock it back and forth while putting pressure on it and it would have been together in a few seconds
@gratefulaya192
4 жыл бұрын
joemama1151 I always put a 2x4 on top of the pvc pipe and use a rubber mallet and I’ve never had an issue
@TaurusGX49MM
3 жыл бұрын
I used dish liquid around the pipe and it’ll go in better....I used clear sealer too..
@frankbolger8249
4 жыл бұрын
Where did you purchase this rubber from, I live in London my name is Frank and can't find one anywhere? Thanks.
@MrEnergyFree
4 жыл бұрын
I USA you can buy it at any local plumber. There is always Amazon. Search for FERNCO P44U-305 Bushing. Thank for watching.
@StONEMASON23
3 жыл бұрын
tell the tech at your plumbing supply that you are transitioning from cast iron to PVC they will know "Fernco is just a brand name
@frankbolger8249
3 жыл бұрын
@@StONEMASON23 thanks.
@Pyridox
6 жыл бұрын
I usually use silicone spray lubricant, and sometimes a little silicone grease applied to the pipe end and the Fernco to help install these rubber Fernco couplings. As someone also mentioned, which I have used in a pinch, cheap liquid dish soap also works good as a lubricant.
@BIGPAWLAK
9 жыл бұрын
butter it up with "duck grease" it will go in smoother
@mgn5667
2 жыл бұрын
then cook the duck 4 dinner ...chuckle
@jcaam8094
8 жыл бұрын
Little bit of silicone spray would have helped you out a lot .
@lmntrlmntr3496
4 жыл бұрын
J CaaM you are correct. In my experience, I have found that when installing a hose in a awkward area as when working in the automotive field, spraying a bit of silicone will make the hose slide easily into place, and then when the silicone dries it actually helps seal the hose in place. So I was wondering about the same effect when sliding the PVC pipe into the rubber sleeve
@588158
3 жыл бұрын
putting some liquid soap on the pvc would make it easier to fit in
@misterfixit121
5 жыл бұрын
A little bit of silicon lube make it easier.
@Zharsergey
4 жыл бұрын
Can I use this for a clay pipe floor drain to convert to pvc?
@MrEnergyFree
4 жыл бұрын
Yes I think so but I ain't 100% sure.
@pauleastend2
9 жыл бұрын
In Ontario Canada.....you can only use white PVC under the floor in the ground and under the cement floor...reason is that in case of fire the off gassing of the PVC is to toxic. ABS above the cement floor....all PVC under the floor.
@mikemarino3635
8 жыл бұрын
+pauleastend2 not where we live. Abs is not allowed in any of the plumbing where we are only in trailer homes or mobile homes because its not permanent. Its against code. We are allowed to use pvc. With your thinking about the toxic qualities , what do you do with PEX which is plastic used for water? or other toxic things in the home when burned, like furniture and wire insulation etc.
@StONEMASON23
3 жыл бұрын
follows the same code as' no combustibles(plastic)in a fresh air plennum.one of the other reasons to use cast iron is,its quieter
@rka375
6 жыл бұрын
How did you remove the old pipe from the hub
@bryede
6 жыл бұрын
I have the same question. I need to convert some of my sewer line as well.
@bryede
5 жыл бұрын
@FoxRcng708 I had a hard time getting enough heat to the pipe as it was only a few inches out of the concrete floor, but eventually we got it broken up and peeled the lead out.
@jhnmcb301
5 жыл бұрын
Use a drill to drill out the lead, once enough is removed the pipe will come out. Bevelling the pvc going into the gasket is a good idea.
@miketayse
2 ай бұрын
I'm doing the same thing! The hub comes out of the floor and I need to make it pvc.
@flynndog
5 жыл бұрын
trust me try rubbing alcohol instead of water, saturat it and don't smoke
@Themadscientist1969
2 жыл бұрын
A light coat of white lithium grease would have helped seat it easily n wouldn;t hurt rubber or cause leaking..
@XIANBLACK
4 жыл бұрын
How do u successfully break out cast and lead from hub?
@gratefulaya192
4 жыл бұрын
Xion Temoc I use a little heat from a torch, you really don’t need to do this if you don’t want but if you do make sure you’re wearing a gas mask and have good ventilation. Anyways if you clean up around the top of the pipe and then take a medium small chisel “I used a 6” chisel” then with the chisel find a groove between the pipe and the lead coated sealant and gentle tap the chisel with a hammer to make the groove a little bigger and slowly work your way around the pipe but don’t rush it and go a little deeper each time you go around the pipe. Maybe you or someone else has another way to do it but I found this was the easiest method for me
@MrEnergyFree
4 жыл бұрын
Be careful with chisel, the hub can break very easy. Use a flat head screwdriver and a torch to melt the lead.
@ChristopherJames4
4 жыл бұрын
precision chiseling / prying, also can drill the lead out with smaller bit
@gman8132
2 жыл бұрын
Drill out the lead around the hub with a drill bit then use a flathead screwdriver 🪛 to scrap and pick it out.
@georgeEPC
7 жыл бұрын
A little mineral oil and you would be in.
@luckimom3
5 жыл бұрын
How do you get the PVC pipe into the cast iron hub?? It wont go in.
@gratefulaya192
4 жыл бұрын
luckimom3 what do you mean? The pvc pipe is smaller than the cast iron pipe and will go in without it being tight and that’s why you need the rubber seal
@MrEnergyFree
4 жыл бұрын
To pass the rubber seal you can put water with soap.
@StONEMASON23
3 жыл бұрын
grease
@emartinez6584
4 жыл бұрын
i would have used petroleum jelly to make pipe slide in easy.
@NHPlumber
3 жыл бұрын
Use duck butter next time
@bradhaenitsch1145
2 жыл бұрын
When there vertical it’s not a big deal
@antoniogalluccio4213
3 жыл бұрын
You are supposed to debur the end of the fitting and put some silicin spray or greasy or even washing up liquid as a lubricant not hammer fittings.. Never seen a plumber hammering the plumbing unless he needs to break the old system
@mohawkmike142
9 жыл бұрын
Best rubber lubricant in the world is brake fluid. That PCV will slide right in and won't harm either the rubber or the PCV. Try it.
@johnm2637
8 жыл бұрын
+moomike laloo anything oil based degrades rubber. silicon spray should be used instead and is a better alternative
@SK-yw5ih
5 жыл бұрын
brake fluid peels paint, eats gloves, nasty stuff, I would never use it on a rubber gasket. Liquid soap is where it's at
@thomasbotch6161
4 жыл бұрын
@@SK-yw5ih You have to watch a lot of high priced plumbers spread bad advice. Same with auto mechanics at 185 and hour they cost as much as brain surgeons.
Пікірлер: 123