I expected the abrasion finger to get dipped in snow too-ice is my injury-prone best friend. I appreciate the muted cutting/grinding. watching your videos is not time wasted---andy
@holzmann8443
Жыл бұрын
You aren't kidding that accidents happen fast with power tools. I inadvertently drilled into my finger a few years ago by holding a part as I was drilling. I hit the exact spot to sever a nerve and leave half my fingertip numb. Fortunately it has 80% recovered since. The rammer turned out great, and with a bit of character to it!
@lundgrenbronzestudios
Жыл бұрын
Oh geez. Drill bits to the finger scare me. I think I fear table saws the most. Glad your finger has mostly recovered though.
@joshlintula9457
Жыл бұрын
Very nice!
@Mistertbones
Жыл бұрын
Nice video! I think you did a good job with this casting.
@lundgrenbronzestudios
Жыл бұрын
Thank you!
@PaulsGarage
Жыл бұрын
Looks great to me! The secret with the feeder is to make it even chunkier than the thing it's feeding. Your feeder was a bit small, so it froze before the rammer, which can make the shrinkage on the casting even worse. I'm sure it will work just fine though 👍 And welding on brass? You're brave! Hope you didn't get sick!
@lundgrenbronzestudios
Жыл бұрын
There is a fine line between bravery and stupidity 😆 Thanks.
@DragonAtelier
Жыл бұрын
The tipped part of the rammer is used to first pack the sand on the nearsest parts of the sand to the edges of the casting box. This prevents the sand from falling out of the box when lifted. Other thing is that I am worried that you will pack the sand too much with a brass sandrammer. I casted mine in aluminum and it is more than enough and you do not get tired so quick. A thing to consider….
@lundgrenbronzestudios
Жыл бұрын
Ah that makes sense. I’ll see how it goes.
@DragonAtelier
Жыл бұрын
@@lundgrenbronzestudios cant wait to see in you next videos how it went 😁
@henrikstenlund5385
Жыл бұрын
Lower the bed temperature instead. That usually helps
@Atanar89
Жыл бұрын
I think you could have gotten a better result of your messy weld by hammering it flat before grinding. Brass responds quite well to that.
@lundgrenbronzestudios
Жыл бұрын
Ah, I didn’t think of that. That might have helped.
@mevk1
Жыл бұрын
Business end is perfect and weight could be too. Large radius fillets where sprue meets casting maybe, and/or either a core, or thicker and/or extra gates, not sure? You could always recast it but why bother, it's a rammer. Casting is perfectly functional and will work exactly as intended. She's a beauty, and THE RAMMER will yield many a masterpiece. Compare this to a shinny ingot hunk of metal sitting on a shelve with zero functionality. Sorry about finger. Just another battle-scar that makes you a tougher, smarter, stronger super-hero.
@lundgrenbronzestudios
Жыл бұрын
Yep. I would much rather use my ingots than to stack them on a shelf.
@drliamwho3642
Жыл бұрын
hey just fyi some elmer’s glue sticks work wonders for cheap bed adhesive especially for abs printing where a brim might not be enough
@lundgrenbronzestudios
Жыл бұрын
Ah Elmer’s glue. For some reason I thought people used hot glue sticks!
@PhilipRomeo69
Жыл бұрын
Brazing probly been better to try looking forward to seeing in use
@lundgrenbronzestudios
Жыл бұрын
Brazing is a skill I haven’t picked up yet. I’ll need to get a torch someday. A big pice of metal like this takes a big torch to get hot.
@rufustoad1
11 ай бұрын
Do you go to a foundry to purchase your brass/bronze/aluminum?
@David_11111
Жыл бұрын
what oil do you add ?
@lundgrenbronzestudios
Жыл бұрын
I save the vacuum pump oil from the pump that I use for vacuum casting. That oil seems to work well.
@cindylundgren1924
Жыл бұрын
Never knew there was such a thing as a "sand rammer" ... good to learn. Remember "SAFETY FIRST" always! Another great video! :)
@robinson-foundry
Жыл бұрын
That turned out really cool looking. Great job! That thing looks like it means business. A glue stick will solve your bed adhesion problems in the future. It come off with water afterwards.
@lundgrenbronzestudios
Жыл бұрын
Thanks for the tip. I’ve heard of people using glue sticks but I haven’t tried that yet.
@MuskratOutdoors
Жыл бұрын
Very neat! I like homemade tools.
@lundgrenbronzestudios
Жыл бұрын
Yeah when the world ends we will need some people who know how to make their own tools.
@MuskratOutdoors
Жыл бұрын
@@lundgrenbronzestudios Yes Sir!
@racheldeatherage1512
Жыл бұрын
Can't wait to see it in action! I think my favorite part of this video was seeing the snow melt 😂
@Plinkster
Жыл бұрын
Great video. I need to get me a 3D printer. So many things you can do with one.
@lundgrenbronzestudios
Жыл бұрын
I resisted for a long time because I felt like it was cheating. But now that I have one the things has been running like non stop.
@Plinkster
Жыл бұрын
I would love to see some lost PLA videos. I’ve been trying to sand cast some coins but I can’t get good details. Possibly because the angles are too straight and grabbing the sand when I remove the coin molds from the sand. I think vacuum casting the coins would work a lot better.
@mevk1
Жыл бұрын
@@lundgrenbronzestudios For simple faster patterns make TKOR's foam cutter. kzitem.info/news/bejne/r2ikxXmYi6yLY5w
@lundgrenbronzestudios
Жыл бұрын
@@Plinkster I've got some lost PLA videos in the works,
Пікірлер: 37