As a young operator who isn't scared of change this looks like a lot of fun to run.
@neilbrown3359
5 жыл бұрын
Its probably ok to run when it's not broke
@geraldpaul4505
5 жыл бұрын
Once they figure out how to calibrate the wear on the teeth/cutting edge on the fly they might have something but old school free hand is still a fine art!
@ryanneal7836
5 жыл бұрын
Gerald Paul you can absolutely change tooth wear. It is an easy measurement that you do. Less than 5 minutes to do.
@geraldpaul4505
5 жыл бұрын
@@ryanneal7836 ya I ran a 360 komatsu with gps and we got the surveyor s to do it ...
@stephendunham9597
5 жыл бұрын
When ALL this shit fails.... bring the old school in and replace it!!!
@nate390
5 жыл бұрын
None of this stuff is new, its been around for 10+ years, it's just evolving and is now coming factory.
@Quadflash
5 жыл бұрын
WOW! Cat is making a lot of the operator's job safer and faster. Wish all this tech was around when I was running equipment
@andrewblais9203
5 жыл бұрын
You should set your GoPro to normal view it won’t look so distorted
@carlosz1124
5 жыл бұрын
Is this made for a blind operator?
@queerasthedayislonglove8950
5 жыл бұрын
Only works when the sensors work. Live Longwall automation, it’s great if everything works. Maintenance is key
@westerntruckandtractorrepa1353
5 жыл бұрын
Let's completely remove the skill of the operator, and over load it with more controllers and sensors to where it's constantly broke down and it two full time guys with laptops to keep the pile of shit running!
@mikewhipkey6863
5 жыл бұрын
western truck and tractor repair Yeah This shit is getting ridiculous.. Just make the Fuckin things Autonomous already.. No Equipment Operators, No Truck drivers, no factory workers.. hell no burger flippers... No jobs period! I'm 33 so hopefully they take about another 2 Decades to implement this that way I'll either be Retired or Dead..
@excavatorfun6265
5 жыл бұрын
yeah no kidding right!
@thewidower1
5 жыл бұрын
Look, I would’ve loved to have all these safeguards on the old junk I ran. It still takes a good operator to get the best out of a good piece of equipment. Talk all you like. This is an extremely nice excavator and I don’t know anyone that wouldn’t love to operate it.
@excavatorfun6265
5 жыл бұрын
@@thewidower1 the older cats are way better than this junk , I talk from experience ,I'm in these things every day
@thewidower1
5 жыл бұрын
excavator fun than perhaps you should be looking for a different line of work because it’s only going to get worse. Technology is coming at ya. Better get used to it.
@mhamma6560
5 жыл бұрын
As a business owner, I'd much prefer the ability to send 3D files / limits to a machine while some low-experience operator gains his legs. This allows me the ease of NOT having to find a 10yr+ experienced operator when we've already proven machines with CNC run circles around humans. They'll soon be fully automated -- no lunch breaks or hang overs to deal with.
@schnitzlercrew
5 жыл бұрын
Thank you Sir" 3d Dimensional" oh yaaaaaa
@79terrafirma
5 жыл бұрын
I done broke out a cab light once. I bet every operator has at one point too. Been operating for over 20 years and none of these gizmos replace experience.
@mhamma6560
5 жыл бұрын
Especially the experience of contacting a live overhead wire wire.
@ryanmartin4292
5 жыл бұрын
So can you set a benchmark and put 2" cut and it will follow?
@ryanmartin4292
5 жыл бұрын
I mean in 2d because if it only works off ur track elevation thats very limited.
@jevlars
5 жыл бұрын
Yes and no, a long you are stationary you can set a cut or fill offset, but if you move you have to set a reference point before you move and then pick that up after the move. This is for 2D machines, with 3D you are can move and wiggle around as much as you want and work off models or reference points.
@ryanmartin4292
5 жыл бұрын
@@jevlars Wonder how accurate it is can you dig a foundation with the 2d if you keep picking up the Reference points.
@jevlars
5 жыл бұрын
@@ryanmartin4292 If the machine and bucket is properly calibrated you have +/- 2 cm On a small open job like a house foundation you can also use a laser.
@thewidower1
5 жыл бұрын
It also has the option of using GPS so it is always setup
@mikem1649
5 жыл бұрын
Cat is just evolving. They see the same thing i see. Its getting harder and harder to find operators. Yes the old guys don't like this technology because they can run it without and have a finished product. The newer generation of operators flat out suck. Not all of them but the majority do. These new operators just don't have it. They can dig a hole and load a truck but when it comes to holding a grade forget it. Dozer or trackhoe. I have some operators ive been trying to teach for almost a year now how to hold a blade and it just doesn't sink in. Ive been through so many operators in the past years i can't even count. I have one guy who is half ass and can run 3d machine control half ass but most of the time im going behind him fixing screw ups. Motor grader operator? Haha you have to pull them out of retirement around here.
@cascapediastjules8796
5 жыл бұрын
Hope it works better than grade control on their dozers
@stevenkerry3101
5 жыл бұрын
just more things to go wrong . you won't need spanners to fix it but a lap top .
@michaelmccarthy4615
5 жыл бұрын
We need "right to repair" laws so these machines can be serviced.
@ArthurDentZaphodBeeb
5 жыл бұрын
And what happens when eXYZ fails and now you swing out into live traffic or hit that powerline? It's great until it fails - and unless there are redundant backup systems, this is an inevitable Class Action lawsuit...
@Wavyink
5 жыл бұрын
Needs to come standard with a DPF/DEF delete kit, don’t really care for all the “technology”. I’ll keep my ole’ fat assed E model.
@michaelmccarthy4615
5 жыл бұрын
Is it like a JD, and unservicable by the owner or any independent shop? Trapped by Cat to be their machine forever.
@rowandrive1
5 жыл бұрын
I understand that technology is a must.but a good driver doesnt need all this .are companys going to pay for a good driver or pay cat or another manufacturer to put a computer to work .a skill will be lost ..
@thewidower1
5 жыл бұрын
fizzy beans it still won’t dig the trench for you or load the truck. It’s just safety measures. Why is everyone so critical of technology? It seems to me, most of the comments are coming from people that have never sat in the seat of a trackhoe.
@yourmomisanicelady8186
5 жыл бұрын
fizzy beans do company’s use cash registers to help the cashiers do their jobs better?🤔👌🏼
@Irven51
5 жыл бұрын
Exactly. Anyone that has worked under ovethead lines and things of that nature can appreciate this type of tech. I've worked in alleys and other tight digging situations, day in snd day out. All it takes is one mistake to damage sn overhead line. It doesn't matter if you have swung the machine 500 times without incident. The one time is what's critical. The people you see complaining about technology are the mass earth movers.....the operators with the least technical skills that sit in a machine mindlessly moving earth all day. They don't like the tech because a robot can do their monotonous job better than they can. Skilled operators that work in rehab of water and sewer utilities where conditions constantly change aren't worried about it one bit. The same with fine grading. This tech eliminates the mindless job of a guy walking around with a grade rod. It's great for small businesses that run lean and have a hard time finding people willing to even show up to work. The people crying about this tech would have cried decades ago when trucks began hauling cargo. Or even horses and wagons. If that would have been stopped, imagine all of the jobs that could have been created by men pulling carts, or better yet, hauling it on their backs.
@evilnia
5 жыл бұрын
And it's still back of the bus to the intelligent Komatsu excavators and their capabilities... the speed and accuracy when Autos are engaged is no comparison.
@Dinoxt12
5 жыл бұрын
Bull Crap!!! Just operate the Dogg-gone equipment, all these Gadgets just to get dust and etc into them and be broke down.
@erinh9660
5 жыл бұрын
any new machine with tier 4 emissions no thanks ill back to the 90s
@thewidower1
5 жыл бұрын
Aaron Hernandez you are an antique. Ultimately you will be out of a job if you can’t keep up with the technology.
@erinh9660
5 жыл бұрын
@@thewidower1 you're right but as of right now the new technology in this industry has not made the recent older technology obsolete. Plus if you understood my comment well enough you would have realized I'm talking about tier 4 equipment only.
@jeremymanuel8136
5 жыл бұрын
Aaron Hernandez yeah I hear ya man... we have a first of its kind tier 4 shovel and it takes 700 litres of def fluid in 24 hours. Trying to get it to clean out the exhaust is a nightmare.
@gangesexcavating
5 жыл бұрын
We have the 336FL at work at it’s a terrible thing, Huge ass, easily dented light metal doors. Lots of computer errors. Huge DEF consumption. It’s actually a pretty slow machine in cycle time.
@excavatorfun6265
5 жыл бұрын
I used one too it was the worst hoe I ever used, and I've been in lots of hoes!!
@gangesexcavating
5 жыл бұрын
3/4 of the engine compartment is dedicated to an exhaust scrubber. It’s ridiculous. The engine is so constipated with exhaust equipment, that I feel the only thing Cat could do is derate the engine RPM and cut back the speed.
@gangesexcavating
5 жыл бұрын
Sure wish I still had an old EX -1 series Hitachi. What was wrong with those? Nothing. The UH series was awesome . Dig and dig and dig and dig. Sadly as technology moves ahead, so does all the problematic computer controlled equipment.
@excavatorfun6265
5 жыл бұрын
say good bye to great operators when there trained on this crap
@Will-tm5bj
5 жыл бұрын
They're*
@danielroe845
5 жыл бұрын
Is all that shit bad for equipment longevity? Almost certainly yes. But is it good for reducing operator fatigue? It's got to be.
@SuperMuddybuddy
5 жыл бұрын
It takes one person to hit a gas,fiber,water etc and you will be complaining how terrible the operator is. Remember slow and steady is efficient,efficient is fast, fast makes the company money.
@AdamPetroffVideos
5 жыл бұрын
doubt you need all that when ur in a 40 acre field with nothing around..
@michaelviens2894
5 жыл бұрын
He made it easier for pond digger's like their job aint easy enough lol
@scruffy6151
5 жыл бұрын
And soon to come the machine with no cab. Just like everything else nobody will have to drive or operate anything just fuel it up and push the go botton tell it what to do and press start. The new way of doing things then if something goes wrong blame the machine.
@ArthurDentZaphodBeeb
5 жыл бұрын
Yup, the entire goal is to get rid of the operators to reduce costs. The Holy Grail is to run mines using a remote control center and a couple of poorly-paid desk jockeys, relying on Indian programmers to generate code and Germans to build the machines. Who wins? Not the poor blue collar schmucks out in the field...
@scruffy6151
5 жыл бұрын
When i bought my first car in 1972 i never thought i would see the day i could buy a fully autonomous car i may see it before i die.
@rightsideofthegrass8114
5 жыл бұрын
@@scruffy6151 Tesla - already here. Go see it before you die.
@Hick25
5 жыл бұрын
ArthurDentZaphodBeeb already happening in Australia mate, rio tinto has already got over 100 fully autonomous cat and komatsu haul trucks, fully autonomous drill rig and haul train, maybe by the end of this year they’ll have a complete autonomous mine site
@scruffy6151
5 жыл бұрын
@@rightsideofthegrass8114 this I know but, i am talking about where they are the normal cars on the road. Yes there are cars that have many option but, non are fully atonamuos. Where the person get in puts the destination in and sit back and read the paper at 60mph and never looks at road. The Google cars are only aloud to do 25mph in town not on the open road.
@markopecurica4463
5 жыл бұрын
More sensors= more breakdowns
@michaelviens2894
5 жыл бұрын
Yeah but sometimes you got to have that shit you got to be in tight spots close counts
@macbook802
5 жыл бұрын
That looks like Arizona dirt
@uddhavamaharaj2919
5 жыл бұрын
Too much technology, after a few years this shit will always be down
@drewdaco1016
5 жыл бұрын
I have been operating hoes for 12 years now and have run a bunch of different machines. But these new cats are absolutely horrible they have completely changed everything in the machine. The controls sit higher and you cant lower the arm rests really low. And as for simple adjustments you have to take your eyes off the job and search through the damn computer to make simple changes its dangerous. And the stupid electronic hydraulics there is no play. To me running this machine is like starting new basically the same as switching from cat to Deere controls. I can not run this machine at all and now my boss is switching over to them and now I have to look for a new job thanks cat I used to like there machines but not now.
@crusader777
5 жыл бұрын
all hot air
@damarissimbolon4129
5 жыл бұрын
☕☕👍👍
@johnlupucyjr.7675
5 жыл бұрын
With all this technology what's the point of having an operator the machine should just operate itself. Just totally pointless and just a waste of time and people's money spend it on an experienced operator
@jsheavy3923
5 жыл бұрын
I work for komatsu. They have had this out already for a few years. There system is a lot better. Just wait they r coming out with a cab less model. No person to fuck it up . Cat is far behind the time. That's w huh y they are a dead company.
@michaelfink9833
2 жыл бұрын
That would take a long ass time to make it a trade with no operators in the cabs. Not even that some of us like to get in our machines and operate making it happen
@arthurchickering9963
5 жыл бұрын
More shit to go wrong ,cost more money
@thepizzadevil7392
5 жыл бұрын
This is by far the ugliest excavator cat has ever made
@technicalrk8435
5 жыл бұрын
like
@Greyhorse15
5 жыл бұрын
Komatsu has a way way way better system....Oh wait that’s why everyone is trying to come up with something to compete with the Komatsu i excavators
@ralph7254
5 жыл бұрын
Eww.
@neilbrown3359
5 жыл бұрын
$300,000 machine. What they won't tell you is you should probably have an extra $50,000 -$100,000 in the savings account for repairs on this hunk of shit!
Пікірлер: 85