I was impressed with the cleanup and quality of the weld. I was a ship-fitter and 3.10 weld inspector at General Dynamics Electric Boat Div. for about a decade. After having seen a number of welders on KZitem it's nice to see someone who does quality work.
@nathanchalecki4842
Жыл бұрын
Wow, electric boats. That's cool!
@chrislabounty3046
Жыл бұрын
If those boats are anything like I've seen from GD they probably take on water and 8 times overpriced.
@johnschmidt2964
11 ай бұрын
Agreed. Looked great.
@thornblackwell5749
11 ай бұрын
@@nathanchalecki4842 GD Electric Boat Division builds Naval nuclear submarines. Yes, they are electric powered by a nuclear steam generation plant.
@bigred06100
11 ай бұрын
Who makes the magnet for the umbrella
@IvyMike.
Жыл бұрын
Hats off to who was doing their checks, easily missed until it's a much larger problem, rare in this day.
@irishlad8797
Жыл бұрын
Very good point I have 2 sons in their mid 20s and they would just plough on until the scraper just stopped or broke n 2 Haha 😎
@WorldsOkayestWelder
Жыл бұрын
That, and hats off to the mechanic that held that thing together for a couple of days.
@kahlzun
Жыл бұрын
That is well spotted, just looked like mud at first
@notorious647
Жыл бұрын
Checks? What checks?!
@IvyMike.
Жыл бұрын
@@notorious647 Umm.. the checks that, umm found the, umm cracks, yes, that's it, the checks that found the cracks, and any other defects, you know looking with your eyes. hope this helps.
@verlinswarey507
Жыл бұрын
That was so cool to watch that scraper pull away as soon as you were done. Makes you realize how important the work that you do is.
@chainarmor448
Жыл бұрын
I’m a mobile diesel mechanic and I fix breakdowns often. Always fun seeing them drive away after a successful repair
@yougoof
Жыл бұрын
The first repair worked and machine did fine for 2 days.
@NIHILWR
Жыл бұрын
@@yougoof xd
@tomtd
11 ай бұрын
Don’t let customers run your business, if it’s going to get a better job done tell them to do what you need and in this case separate the machine. Your quality will depend on you doing the very best job. Your skills should not be compromised by lazy customers.
@pipthewarrior3738
10 ай бұрын
@@yougoof Did fine for two days but maybe on the third it would blow up and kill a small family of rodents like yours
@keithjackson2151
Жыл бұрын
I’m a mechanic for the company that contracted those scrapers I actually saw you doing that the other day and had no idea who it was. Funny seeing this video haha
@khrisjackson5042
Жыл бұрын
I actually ran this exact scraper in Northern Nevada 2 years ago!! Crazy how small of a world it is!!
@RallyanAndyco
Жыл бұрын
I currently run one !
@seeharvester
Жыл бұрын
This one? How can you tell?
@Jdl223
Жыл бұрын
@seeharvester it's numbered a red 214
@grifon1981
13 күн бұрын
Stupid question, but what does a scraper do? What is this machine for?
@gagt5spd
13 күн бұрын
@@grifon1981 moves dirt, self loads through the belly then dumps somewhere else out the belly again.
@troubleis5271
Жыл бұрын
love seeing these "in the field" repairs in your content. Always great to see how a pro tackles something like this in less than optimal conditions and is still able to produce a quality result. Makes me realize i still got a lot of learning to do. .
@hasteandfury2424
10 ай бұрын
Where else is he going to work on it? In a covered stadium?
@dirtyfabrication401
4 ай бұрын
Yessir!!! Always keep an open mind and stay humble. I've been at it 27 years and keep learning new tips and tricks that make my work more effective and efficient. Never stop learning and you will go far
@codecircle423
5 ай бұрын
That was a smooth job sir. Bravo! You know that when a company is pulling off as soon as you're done, you know just how badly needed someone that knew what they were doing.
@randyharris8669
Жыл бұрын
Thats a darn good repair. Its impressive how thick the material is and still manages to crack out, none the less thanks for sharing and nicely done.
@joaocosta3374
Жыл бұрын
Exactly, imagine the tensions on the material.
@davidbrennan5
Жыл бұрын
Sometimes it is better to have some flex. When you overbuild the structure, you need to add reinforcement sometimes to prevent cracking. We had similar issues with some of our mining trucks and had to add gussets to the areas prone to cracking. The miners are very hard on the equipment.
@Smachfest
Жыл бұрын
@@davidbrennan5 Re-enforcing one area can lead to failure on another part. The design should incorporate all of that. Then prototype and In-the-Field production. We beefed up 'tag links' of Articulate Off Highway Truck suspension brackets that were failing in new trucks. The trucks had been modified by the customer to carry more then their designed load. At first, the truck suspension would not lift the truck when loaded by the shovel. (Too much muck in the body.) The OEM sent us relief valve cartridges of a higher value. (2800PSI rather than the 2300PSI spec.) That meant the truck suspension operated correctly. But the extra loading meant the suspension mounts started breaking off. We fitted re-enforcement. Then the frames failed. The OEM sent much meatier brackets to spread the loading over a lager area of the frames and axles. That cured the problems. The OEM adjusted their design decisions after that to cater for greedy customers and keep their sales figure up.
@ericdingman3050
10 ай бұрын
gotta remember there’s big d-11’s pushing against them alot of times and that’s the focal point is there and on the blade on the bottom of the bowl
@murmenaattori6
20 күн бұрын
Metal fatigue is an issue. Steel can generally handle metal fatigue well, but cast steels less so.
@BuildSomethingAuto
Жыл бұрын
That's an impressive plasma cutter! 1 to 1 1/2" thick material and it came out clean 😮
@engjds
21 күн бұрын
Must be over 100A?
@applesauce2085
Жыл бұрын
As a 17 year old who wants to work with my hands. I love these videos loads. I love learning something useful for me in school and seeing what i have actually done is so much more rewarding than just a piece of paper. Love the content!
@alexguigui1877
6 ай бұрын
This being my dream job, 3 months ago, i decided to quit my steel carpentry job, and start doing some welding repairs. I’m repairing a lot of rotators tow trucks. And car carrying trailers. Repaired my first excavator today! A CAT 320. And god it pays pretty well !! I really love doing this kind of stuff.
@mitchweber7868
2 ай бұрын
Steel carpentry whats that? did you do like steel staircases or something like that?
@alexguigui1877
2 ай бұрын
@@mitchweber7868 i don’t really know how it’s called in English, but it consists of building heavy things in steel, like bridges, or frames of some buildings, staircases is what i would call a small job. I used to work with 3-6 inches thick steel plates. But when i was an apprentice, i learned how to build smaller stuff like stainless steel fences, tables, or divers things in steel, stainless, and aluminium
@mitchweber7868
2 ай бұрын
@@alexguigui1877 That sounds awesome man 😎 that sounds like a fun job no doubt
@brutusbarnabus8098
Ай бұрын
@@alexguigui1877 you were a steel fitter, bro. some would call you an ironworker.
@engjds
21 күн бұрын
How did you find the work?
@kevinloza30
Жыл бұрын
The KZitem certified mechanic sticker on the back of the truck is amazing
@krisjones0926
Жыл бұрын
as an agricultural welder this is some good stuff! love to see some proper field repairs
@aztharz5637
Жыл бұрын
I weld oil storage tanks at tank farms, and the steel is about an inch and a half thick. I've always wanted to get into heavy equipment repair. it looks like you did a good job. 👍
@jasonb7878
Жыл бұрын
Thanks for taking the extra time to show us. Great welding!
@peteacher52
Жыл бұрын
I was especially impressed by the Isaac-like accuracy of your freehand plasma cut and how you made a difficult task look routine. 😊🙂
@zoidsfan77
Жыл бұрын
I wonder how many people will get your reference.
@MegaLojay
Жыл бұрын
@@zoidsfan77 here's one anyway
@valoraboveall5793
Жыл бұрын
I am ignorant, but is this a circumcision reference? If not then my apologies.
@MegaLojay
Жыл бұрын
@Valor Above All nah. It's a reference to another welding youtuber. I.c. weld. At least I think. Now you got me wondering.
@zoidsfan77
Жыл бұрын
@@MegaLojay Engineer Isaac Clarke from the horror video game series Dead Space. One of his primary weapons is a handheld plasma cutter.
@crunchbbq7488
Жыл бұрын
Nice job on stitching it up. When I was building and repairing railroad cars back in the day, I used to use a air arc to cut all the welds out. I could chase a crack much more easily than a plasma cutter.
@jeffallen6754
5 ай бұрын
I used to love getting out in the field and welding. I’ve pretty much been in shops for the last twenty years.
@sjfodor
Жыл бұрын
That was an impressive field repair. You must have been hustling to get that done in 5 hours. Quality work. Thanks for sharing.
@fordshaw5833
Жыл бұрын
Field expedient repairs are just that - a way to keep equipment working and making money. The real permanent repair is the shop job I see . All in all I really enjoy the whole process of problem solving solving each repair takes.
@ypaulbrown
Жыл бұрын
Greg, always great to be watching your adventures.....best wishes from Florida, Paul
@fordshaw5833
Жыл бұрын
You’re welding skill is amazing. And, you video production skills are also top notch.
@ronpatterson5483
Жыл бұрын
Amazing watching all your work, amazing work fixing things outside🤘🤘🤘
@WorldsOkayestWelder
Жыл бұрын
Worked down on the grapevine for a little while. Beautiful country and amazing weather. Good repair work!
@SilverKnife0311
Жыл бұрын
I just started watching your vids. I am amazed with the work that you do. The was you opened up the crack and filled it in was AWESOME!
@briangrossen7982
Жыл бұрын
Pretty interesting how you handled this one I’ve been a heavy equipment mechanic and I’ve always seen people cut big chunk of material out and put another piece of material in a weld it up but you can always see the patch I like how this was seamless looked great too
@thomas4844
Жыл бұрын
You seriously do great work. The one thing you can’t hide after a weld then grind is porosity. After you blend it all together it’s clearly smooth and without any pinholes or imperfections. Damn it looks good Greg.
@moshunit96
Жыл бұрын
Thanks for taking the time to show the process. Nice work.
@troythegardener
Жыл бұрын
Wow, amazing job. It's inspired me to take up a welding class in the evenings, start 2 weeks on Thursday!
@danielpullum1907
Жыл бұрын
I enjoyed seeing the area where the machines are working. It would good to tell us what the whole project is(mining, dam, etc.) You put an amazing amount of weld into that repair. You clearly have a lot of confidence in your welding skill. My experience (mainly from new machine building at CAT) welds fail from porosity and proper cleaning before, during, and after the welding. I've seen so many welds done on dirty metal. I appreciate your cleanup and painting to complete the job!!!!!!
@taowroland8697
Жыл бұрын
Its solar or windmill nonsense. They're basically screwing the desert beyond belief with all that trash. Used to walk/hunt out there for miles and miles and not see a soul or a fence, and now theres a thousand graders absolutely raping the landscape and taking up all the space.
@davep6977
6 ай бұрын
I wanted to see more on how he did the backer plates. Beautiful work
@PH-md8xp
Жыл бұрын
Wow, excellent repair. That scraper is good as new. Was fascinating to see your process of fixing it.
@vicchiapetta4166
Жыл бұрын
Great job as always!! I sure love your videos!! Thanks again, Vic!!!
@_DS83_
Жыл бұрын
Люблю такую работу, особенно когда ничего не мешает, когда хорошая погода. Вырезаешь, завариваешь, зачищаешь, отдаешь в работу. Сварка на релаксе :)
@gregweinfurtner7774
2 ай бұрын
Quite a fill in job. As usual, well done and thanks for taking us along for the ride!
@timgruver5932
Жыл бұрын
I loved doing repairs etc like this. Every day some new mess to figure out. Sometimes they became not only daunting but a huge challenge. The winter work added to whole process. I got where I would go to Georgia or Florida for 6 months lol and find work there. Quite a repair you did on this mess. 👍👍🔥👀👀
@shaunolinger964
Жыл бұрын
Watching you do this job makes me eager to get back to work in my own shop. My father passed away last year and left me his entire stock of tools and equipment, including a plasma cutter and very nice welder, among a great many other useful items. Some of these tools I remember him using while I was still in my single digits, and I'm near 50 now. As for your "office"... you couldn't ask for a finer work site. I am a retired heavy construction carpenter... some of my most favorite job sites were outside, weather be damned. Nice job partner. I'm gonna stick around a bit... prowl around your page a while. I'll try not to be too obnoxious. 😅
@luc_xott
Жыл бұрын
Awesome work man, respect the craftsmanship.
@gordonagent7037
2 ай бұрын
Beautiful repair sir, love a man who goes the extra distance to make the finished job look aesthetically pleasing to. Well done
@Tom-bo2wj
Жыл бұрын
Very impressive. Great finish work. Could even tell it was broken. Something about watching these types of videos is relaxing
@robinjchambers845
Жыл бұрын
That’s a lot of weld……..your good at that. Enjoy your vids
@GhostBranchFPV
8 күн бұрын
Not gonna lie, I kinda was expecting to see you fix it with chinese noodles and superglue. But this way also works. Kudos!
@Smachfest
Жыл бұрын
We used to weld repair Cat 777 rear diff casings where they cracked between the bolt holes. And big shovel buckets etc. Cat normally provide Weld Repair instructions for those critical jobs. I remember they were very hot on Weld Inclusions. They recommended that 'grinding stones/wheels' were avoided in final surface prep prior to welding. The little bits of abrasive get lodged in the surface and then form pockets deep in the weld which can cause failure. Even as the weld cools the inclusions can create micro-cracking. If the cracks join up over time and loading, the repair can fail. I notice you use a carbide- burr to clean out after the plasma cut but then change to a wheel to chip slag between runs. We used a needle gun to chip slag as part of Cat instruction. The needle gun also peens the new material and helps unload surface stress due to shrinkage of the weld. I can imagine the mechanic's emotional state when he saw the crack. That repair looked absolutely lovely when finished. And the Cat Paint in the rattle can goes on great. We use a lot of it too. Our lazy ass welders never consider the aesthetics of their work though. The mechanic has to paint over the welders work. And that is just not cricket. 😀
@johnblecker4206
Жыл бұрын
That was one deep crack from the start which you turned in to a perfectly smooth and neat repair job.
@LaSouthernGemini
Жыл бұрын
You are an ARTIST! The way you built that metal so perfectly, line after line, until it was the same level as the original metal was admirable. Then you scraped it down to match the original metal for painting. I am looking forward to future videos.
@user-me8bw4es4y
8 ай бұрын
Рыцарь стального шва и голубого огня! Отличная работа!
@harveystephens6115
Жыл бұрын
Really enjoy watching you fix stuff!!!!!
@TheUnseenWaffle
Жыл бұрын
The end result. Well done! Your pride shows in your work. Keep it up!
@R.A.G81
Жыл бұрын
Отличная работа!👍. Я сам работаю сварщиком и занимаюсь примерно такой же работой в России. Примите мои комплименты за ваш профессионализм! Привет из России, из Сибири!
@Odessa-2maya-2014
Жыл бұрын
Если оно там треснуло то сто пудов опять лопнет. Наварили бы полос для мощи.
@58Rev
Жыл бұрын
A.G.R Держу пари, у вас есть несколько историй о сварке в холодную погоду!
@R.A.G81
Жыл бұрын
@@58Rev есть) вы выиграли пари)))
@danielmartin531
Жыл бұрын
какие машины вы там используете? какие-нибудь, в частности, выдерживают холод лучше, чем другие?
@R.A.G81
Жыл бұрын
@@danielmartin531 в основном " caterpillar". И старые, произведенные ещё в советском союзе. Но сильных морозов не выдерживает ничего)))
@jtg2737
Жыл бұрын
Excellent job! Hello from Texas!
@glenngosline1710
Жыл бұрын
Beautiful job as always. A true professional.
@jaymarshall7632
Жыл бұрын
Thank you for your videos. Please keep them coming!!
@JesusThineBeTheGlory
Жыл бұрын
I can imagine that was a bit difficult but you did such a good job of it. True professional welder
@mortjoer
Жыл бұрын
1:20 seeing those scrapers thundering towards eachother had me going for a second hahaha 😊 Edit: Just finished watching, nicely done sir!
@davegavin7914
Жыл бұрын
Fascinating to watch a true professional at work 🏴👍🏻👏👏👏
@horstszibulski19
Жыл бұрын
Wow, that seems to haven taken a whole spool of wire, if not more... Great job, thx for showing! 👍👍👍
@johnkoury1116
Жыл бұрын
I am really looking forward to seeing how you do this one. I repaired a hole in the case of a skid loader using muggy weld. I know it sounds silly but the sticks I get from them were perfect.
@shawnmann9491
Жыл бұрын
Did you use the Muggy to fill the hole in a gearbox case or engine case? I’ve read good things about Muggy.
@johnkoury1116
Жыл бұрын
@@shawnmann9491 I used a piece of aluminum but yes I used Muggy to weld the aluminum and it turned out beautifully. I recommend highly. I found muggy from Branden Luft's video about it.
@quackula9190
Жыл бұрын
WOW! He's like a plastic surgeon for tractors.
@petermccuskey1832
Жыл бұрын
Really nice work especially the plasma. Spot on sir. Back in the day before I had my suitcase I used stick and would gusset the exterior along the X axis towards the rear of the knuckle towards the pan for about 8 inches and it would stop it from occurring again. It could be because I was using stick that I had to gusset it. Again you do very nice work
@kam2142
Жыл бұрын
This video is so natural, I never been to the US and I have never seeen snow in my life. I apperciate very single detail my man
@handlevanmijnaccount
Жыл бұрын
Very nice repair. Truck tour soon?
@firstgenerationfarmer9991
Жыл бұрын
Awesome!!
@kentsmith2164
Жыл бұрын
Nice job! I did a pan. I believe it was a Michigan many years ago. Big one around here. Had the same break. I did it with a torch and 7018 up welds. That was before I had plasma's and a wire feeder! Lol! Great job! Kent
@ricfair9919
27 күн бұрын
BEAUTIFUL WELDING! Great job.
@byker4lyfe1
Жыл бұрын
Amazing... I'll bet you went through alot of wire on this one. Too bad you had to grind the weld down it looked totally awesome , anyway great job
@jazko
Жыл бұрын
Yeah, I never understood why is it the standard to grind down the welds to blend them. I think a good weld is a beauty to see. Unless they will be selling this machine and wanna hide the fact that there was a repair done.
@At-Imperial-Walker
2 күн бұрын
I was shocked to see him begin to grind the weld but then the quality person in me realizes the true beauty of a good weld is to never have known it was welded. Amazing.
@thebanjoman1963
6 ай бұрын
The OCD in me would still be cleaning....
@RogueRestorationsLTD
Жыл бұрын
You sir are an absolute genius and true expert great channel for skills .!!
@middleway1885
10 ай бұрын
Golf clap~! Keep doing what you enjoy! Can't get enough of these quality work)
@brandonb6164
Жыл бұрын
Beautiful work Greg. I really like these videos.
@LanceMcGrew
Жыл бұрын
Just like patching drywall :)
@baxtergk1
Жыл бұрын
I'm a beginning welder so there's lots I don't know: That's a pretty massive cast assembly but I wonder about the amount of heat you had to put into it. Did you have to pause along the way to let it cool at all? Did you use a temp gun to measure the temp or just experience?
@OFW
Жыл бұрын
I did use a temp gun to watch the heat. I had to stop for 30 minutes one time.
@dans_Learning_Curve
Жыл бұрын
@@OFW what heat did you stop at? What would have happened if you kept welding?
@OFW
Жыл бұрын
@@dans_Learning_Curve I like to keep the material at 600 degrees or less. It can crystallize if it gets too hot which causes a list of issues.
@jessecooper2955
Жыл бұрын
Funny when you said til they break it again. They may Crack it in another spot but not where your repair is. Fantastic vertical and overall 10/10 for quality and workmanship! Great to see someone still taking pride in their work !
@nedudki
10 ай бұрын
Kudos doing this type of repairs on the field!
@grahamzazzara2340
Жыл бұрын
Also think about using an air needler after each pass. It helps with destressing the weld
@gutsngorrrr
Жыл бұрын
Great job as ever. Out of curiosity, why don't you do a dye penetrate test, to check for cracks?
@OFW
Жыл бұрын
I did think about it. The main reason is I forgot the die at the shop as I was in a rush.
@slash.9882
Жыл бұрын
Very interesting video depicting the expertise needed to repair this correctly. Subscribed
@rudevectors8018
3 күн бұрын
Amazing work. And what a cool job to have. Thanks for the video.
@rhiekel
Жыл бұрын
Nice job. Probably should have preheated it a bit for a stronger repair . Also get a needle gun for chipping out that slag. It does a perfect job. ( Former certified welder)
@OFW
Жыл бұрын
I did pre heat a little. I almost got out the needle gun but I didn’t want to keep the compressor running for a few hours just for that.
@rhiekel
Жыл бұрын
Haha ok, did not mean to nitpick. I used to work in a shop doing large structural pieces, and we never ever welded anything that was not preheated, and tested with a heat stick. The parts were for a nuclear power plant, and every weld was x-rayed. So you learned pretty quickly how to do perfect welds, or you no longer worked there... 😃
@johnnybird7593
11 ай бұрын
Preheat depends very much on plate thickness and carbon content in material. 1 inch doesn't usually need much unless working in cold conditions. I do welding repairs on oil platforms in the North Sea.
@NICK-uy3nl
Жыл бұрын
That is a gross structural failure. Cat is not using the right alloys with high tensile strength, or could be a bad casting, or both. I am sure your weld is 10 times stronger than the base metal.
@crazy_mind-ox8if
12 күн бұрын
Everything has a service life. While yes, it is possible to design parts strong enough so it won't fatigue and crack, if you tried to do that on bigger trucks and machinery, it would get so big and heavy it would either collapse under its own weight, or be so expensive nobody could buy it. CAT predicts exactly how many service hours things should last, and I'm pretty sure if you ask them they'll tell you. It always tends to break on welds because the root of the weld is a huge stress concentration point. And without re-heat treating after a weld, that will forever more be a weak spot. So I'm not sure CATs guidance on this repair, I'm sure its fine, I can almost guarantee you, the weld probably isn't stronger than the part originally was. Maybe close, but it will fail again. Probably sooner. There are some newer patents from CAT which should move the root of the weld out of the load path on structure critical future parts. But you didn't hear that from me. Either way, not a gross design failure. It failed as intend, probably when predicted. Otherwise CAT would recall the part and fix their design like they've done on some many other parts.
@NICK-uy3nl
12 күн бұрын
@@crazy_mind-ox8if - The heart of good design is knowing the high stress points and doubling up on structural integrity of the weak point. It does not mean making the entire machine heavier but recognizing weak points (either by computer analysis or field reports) and improving it. It is a process that should be ironed out during product testing phase before the machine is put into production. I don't see such gross structural failures on reputable brands, like Komatsu or Liebherr, because they put their products through rigorous testing before selling them to customers.
@crazy_mind-ox8if
10 күн бұрын
@@NICK-uy3nl I'm telling you, I've talked to the design engineers on an almost weekly basis for a while now. Every other sentence is "but that would increase weight". I don't know where the push comes from, but I can almost guarantee you the crack was predicted in FEA, and is part of the regular service advisory for that machine. I work at a foundry that makes most of these parts, and I've seen what happens when parts fail sooner than expected. It takes a while to make a new design, so it might be 2 or 3 years, but when something actually fails when it shouldn't, customers get upset and they 911 a new part through the process. Currently doing that on some frame components for some of their dump trucks. Oh also, CAT does have a proving ground, and they test it for months if not years before anything gets put in production. Its not just komatsu and liebherr
@NICK-uy3nl
10 күн бұрын
@@crazy_mind-ox8if - Seems to me Cat safety margins are way below industry standards. That can come from either arrogance or ignorance. Maybe they need smarter engineers with modern tools for design and failure analysis to keep up with the competition.
@MarkSmith-rk3iv
6 ай бұрын
Good Job ,,, I used to assemble the back end of the 657's before I retired a few years ago ... Definitely built strong :)
@InCountry6970
6 ай бұрын
Super job and excellent welding. Even your camera work is top shelf, just great. Thanks
@cab8188
Жыл бұрын
Do you know what they are constructing there ?? Great video's Thank you !
@OFW
Жыл бұрын
They are digging a hole for a land fill I believe.
@MrPWH12345
Жыл бұрын
This was great. I'm not a metalwork of anykind just an engineer that appreciates craftsmen at work!
@rapturebound197
Жыл бұрын
That looked really daunting but you took it on and did a fantastic job! 👍
@driverjeff1498
Жыл бұрын
The amount of back and forth force that those necks take must be off the charts.
@WayneWerner
Жыл бұрын
Definitely off the chart of how much force that neck could handle 😜
@aldo-228
6 ай бұрын
Just amazing work sir! I'm truly impressed.
@ronaldbrosius7488
Жыл бұрын
Wow!! Excellent job!! Well done, you nailed it.
@frankrodriguez5202
9 ай бұрын
I'm a mobile diesel mechanic and damnnnn.....great work. Loved the video
@codyprice5662
Жыл бұрын
You can definitely go home and be proud of that one. Nice work👌
@EricWakefield-ls9ph
6 ай бұрын
very satisfying to watch ☺️ excellent work by the way! the intense heat needed to cut that steel is easy work for that plasma cutter!!! phenomenal!
@philp1072
Ай бұрын
Total badass man! I can only hope to ever weld like you
@banuamekanikal454
5 ай бұрын
special welding results, I am happy to see the workmanship
@satan2k
Жыл бұрын
No idea why I got this video recommended, but I kept it going until the end. It was so satisfying. Impressive job!
@dobraydien7242
Жыл бұрын
Reminds me of when I used to work on locomotives doing wreck repair. Those were rather interesting sometimes
@dustysherrmann4427
Жыл бұрын
A very good job under these difficult conditions 👍
@alexandrsherbakov9878
6 ай бұрын
t's nice to see the work of real professionals, the weld is completely free of scale! Respect.
@ebk304
3 ай бұрын
Just incredible how you blended that
@tiamat9149
Жыл бұрын
I ran a Wabco 353 single engine scraper for 4 years, in the iron mines of northern Minnesota, it was brand new back then. Might have the model number wrong. Never ran a scraper before. Forman's instructions was, "get in and get to work"!! that was it. I got pretty good at operating this giant. I did have a couple of close calls, I did spin it completely around on an icy road, that was fun.
@zxborg9681
Жыл бұрын
Man, I really miss having a job where you do some work and see the result put into action right away. Nice work!
@0ohoaxo0
Жыл бұрын
Man I love driving to Mojave desert…this past season it started snowing. Mind you I live by the beach in CA. So cool
Пікірлер: 1,4 М.