Thank you sir finally a video that makes since yesssss
@hobbyelectroniccircuits7391
7 ай бұрын
You are welcome 🙂
@mnk1964
5 ай бұрын
Very nice projects. Thanks for uploading circuit diagrams
@hobbyelectroniccircuits7391
4 ай бұрын
You are welcome and Thank you for admiring my work.
@jozefnovak7750
4 ай бұрын
Super! Thank you very much!
@hobbyelectroniccircuits7391
4 ай бұрын
You are welcome friend 👍👍
@warflag007
2 жыл бұрын
Thnx man 👍
@hobbyelectroniccircuits7391
2 жыл бұрын
You are welcome..😊
@thilinalakshan2795
2 жыл бұрын
Ela 🔥❤️👌
@hobbyelectroniccircuits7391
2 жыл бұрын
Thank you....
@andresburga2149
Жыл бұрын
Very nice
@hobbyelectroniccircuits7391
Жыл бұрын
Thank you 😊
@GurinderSingh
Жыл бұрын
Can I use 4015 ic as 74hc 595 -be or +be both led supply
@hobbyelectroniccircuits7391
Жыл бұрын
Pins are not compatible. 1st circuit only supports CD4015 and 2nd CD4017
@asr.rizqi_
Жыл бұрын
each ic output is given 10-20 leds in 12v series, do you need additional transistors sir?
@hobbyelectroniccircuits7391
Жыл бұрын
Assume you are going to connect 20 LEDs per each output of the transistor, then you have to use five LED segments where four LEDs connected in series in each segment. Also use D400.
@pejuangrupiah1758
Жыл бұрын
Mantap
@hobbyelectroniccircuits7391
Жыл бұрын
Thank you...
@harshadsuru625
2 жыл бұрын
Nice video sir. Or konsi led le sakte hai replysir.kosa color me 5mm le sakte hai replysir.
@hobbyelectroniccircuits7391
2 жыл бұрын
Thank you.. You mean the type of LEDs that used in the flasher circuit?
@tharangadikkumbura
2 жыл бұрын
ඒකනම් නියමයි අයියෙ .... 👍👍👍👍👍👍👍
@hobbyelectroniccircuits7391
2 жыл бұрын
ස්තූතියි.. හදලා බලන්න.👍
@pasansankalpa7291
2 жыл бұрын
සුපිරි
@hobbyelectroniccircuits7391
2 жыл бұрын
ස්තූතියි..
@hobielektronika959
Жыл бұрын
Hobi Elektronika Coming 👍🏼
@hobbyelectroniccircuits7391
Жыл бұрын
Nice 👍
@Nasrul-NSL
2 жыл бұрын
👍👍👍💕 from Indonesia. Plase upload video desigen sircuit filter audio compressor -limiter - flanger -reverb - Low delay 🙏
@hobbyelectroniccircuits7391
2 жыл бұрын
Thank you for admiring my work and your suggestions. I will upload those circuits after successfully tested practically.
@LOUDMUSIC001
Жыл бұрын
Meka wada meka supir
@hobbyelectroniccircuits7391
Жыл бұрын
Thank you 😊
@michaelromeo5658
3 ай бұрын
can you make a similar circuit with premade 12volt color light strips?
@hobbyelectroniccircuits7391
3 ай бұрын
Are you asking about how to connect 12V LEDs into this circuit ? Please watch 00:45
@arunlalarunlal1308
2 жыл бұрын
There are 3 connections in the preset and only 2 connections in the circuit where a given connection I will be connected
@hobbyelectroniccircuits7391
2 жыл бұрын
Yes. It is correct. Use center pin and one of the other pins for the circuit. The other pin is free and not connected to the circuit.
@tomference4618
Жыл бұрын
..the 100uf capacitor is not shown on the PCB,..is it on the backside?
@hobbyelectroniccircuits7391
Жыл бұрын
100uF capacitor is used for smoothing purpose. I have tested these two circuits using a 9V battery, so further smoothing is not required and didn't use the 100uF capacitor.
@tomference4618
Жыл бұрын
@@hobbyelectroniccircuits7391 👍
@sourabhsanu3496
Жыл бұрын
Sir daiod hm IN 4007 bhi laga shakte hai kaya
@hobbyelectroniccircuits7391
Жыл бұрын
You can use 1N4148, 1N4001, 1N4004, 1N4007 or any rectifier diode.
@vishvajeetlegend3077
Жыл бұрын
How much leds connection possible?
@hobbyelectroniccircuits7391
Жыл бұрын
It depends upon the output switching transistor. For a 12V supply, you have to make segments by connecting four LEDs in series. C945 or C1815 can drive 5 segments (4×5 = 20 LEDs per one transistor) Use D400, BD139 or D313 for more LEDs or 12V LED strips.
@mashooqueali4241
3 ай бұрын
Can use 10 k preset Or 50k potinterometer
@hobbyelectroniccircuits7391
3 ай бұрын
50k to 100k Potentiometer or Preset
@arunlalarunlal1308
2 жыл бұрын
2.2 uf volt how much
@hobbyelectroniccircuits7391
2 жыл бұрын
16V or 25V or 50V
@hadiyahyayie7517
9 күн бұрын
cd4015 can use for car?
@hobbyelectroniccircuits7391
9 күн бұрын
It is good to use a 7810 or 7812 regulator and a fuse for the positive terminal taken from the battery.
@wimathmusic123
3 ай бұрын
what is input vol tage 🤔
@hobbyelectroniccircuits7391
3 ай бұрын
6V to 12V DC
@wimathmusic123
3 ай бұрын
@@hobbyelectroniccircuits7391 ❤️
@dimpleverma1603
2 жыл бұрын
Ek board milega kya y
@hobbyelectroniccircuits7391
2 жыл бұрын
This circuit is not for sale friend. Please follow the video to make it yourself..👍
@jatikusumo3639
Жыл бұрын
Bagaimana jika di aplikasikan ke aki 12v
@hobbyelectroniccircuits7391
Жыл бұрын
It is working with any 12V battery. Use a fuse around 1A for safe.
@tiewcheerong9241
2 жыл бұрын
boss,this can use for car??
@tiewcheerong9241
2 жыл бұрын
boss,do you have a contact number??Like a photo of the electric panel that I want to show you Clearly…
@hobbyelectroniccircuits7391
2 жыл бұрын
Yes, 12V is ok. Email - Lahiru1225@gmail.com Facebook - Lahiru Bandara
@led9552
Жыл бұрын
kzitem.info/news/bejne/qYiMyGWZb3ymeZg
@datorkateclarissel.714
7 ай бұрын
Hello po pwede po kayang makita ang pagkakahinang nung likod ng knight rider
@hobbyelectroniccircuits7391
7 ай бұрын
English ?
@lyphongvlog3283
5 ай бұрын
tôi có thể thay 1N4001 bằng 1N4007 được không
@hobbyelectroniccircuits7391
5 ай бұрын
Yes. You can use any diode in 1N400x series such as 1N4001, 1N4002...1N4007 or 1N4148.
@lyphongvlog3283
5 ай бұрын
ok cảm ơn bạn. còn vấn đề về bóng bán dẫn tôi có thể thay thế C945 bằng BC547 được không.
@hobbyelectroniccircuits7391
4 ай бұрын
You can replace C945 by BC547/548, but remember that their pin configuration is different. If you start from left hand side, C945 has E C B configuration while BC547 has C B E configuration. Connect it correctly. Good luck with your work.
@xbicff3059
Жыл бұрын
hello kollo mn aluthin. mata kiyanna mekata cd4017 danna puluwanda kiyala
It is not possible to get only 6 outputs from CD4015. Use CD4017 for any number of outputs from 2 to 10.
@FacebookNoName
Жыл бұрын
@@hobbyelectroniccircuits7391 I want to use CD4015 BECAUSE the effect is nice "Rain Drop Effect"
@hobbyelectroniccircuits7391
Жыл бұрын
You can obtain this Rain drop effect from CD4017 with few diodes at the outputs.
@FacebookNoName
Жыл бұрын
@@hobbyelectroniccircuits7391 you please help me
@hobbyelectroniccircuits7391
Жыл бұрын
Send me your facebook link or email address, I will draw and send you soon as my possibility.
@LOUDMUSIC001
Жыл бұрын
Ayiye mata meke eka balb ekak paththu wenakota led 16k paththu karanna one kohomadha karanne
@hobbyelectroniccircuits7391
Жыл бұрын
මොනවද දාන bulb වර්ගය? මම වීඩියෝ එකේ දාල තියෙනවා diagram කීපයක්ම, C945/C1815/D400/D313 වගේ transistors හරහා normal 5mm LED වැඩි ගානක් නැත්නම් 12V LED පටි drive කරන විදිය.
@LOUDMUSIC001
Жыл бұрын
@@hobbyelectroniccircuits7391 meka man budurasmalawakata danna inne 3mm clear led danna hithan inne whatsapp number eka dannako kathakaraganna
@LOUDMUSIC001
Жыл бұрын
@@hobbyelectroniccircuits7391 led parallel කනෙක්ට් කරන්නෙ
@hobbyelectroniccircuits7391
Жыл бұрын
LED හතර ගානේ series කරපු කාණ්ඩ දාන්න. වීඩියෝ එකේ 0:45 & 3:20 තැන් වල බලන්න diagrams පැහැදිලිව දාල තියෙනවා.
@LOUDMUSIC001
Жыл бұрын
@@hobbyelectroniccircuits7391 thanks ❤❤
@vashuelectronic3826
Жыл бұрын
4015 ic ka 5 channel ka daigram ka photo bhejiye sir plz help me
@hobbyelectroniccircuits7391
Жыл бұрын
There are 8 outputs in CD4015 circuit. What if get 5 outputs from CD4017..?
@darshanpatel575
Жыл бұрын
sir cd4015 wala circuit baraber he?? mene try kiya nahi ho raha he...help me
@hobbyelectroniccircuits7391
Жыл бұрын
Are you asking about equality of CD4017 and CD4015...?
@darshanpatel575
Жыл бұрын
@@hobbyelectroniccircuits7391 mera rain drop wali circuit work nahi kr rahi he ,, video me aapne jesa circuit bataya he mene use follow kiya he!! ,,,Circuit baraber dekhaya he aap ne video me???
@hobbyelectroniccircuits7391
Жыл бұрын
Kindly can you explain in English..?
@darshanpatel575
Жыл бұрын
@@hobbyelectroniccircuits7391 rain drop circuit is not working....
@hobbyelectroniccircuits7391
Жыл бұрын
Did you follow my diagram correctly with CD4015, NE555 and C945 to make the circuit...?
@krhd6817
Жыл бұрын
वर्षा प्रभाव का dayogram मिलेगा
@hobbyelectroniccircuits7391
Жыл бұрын
🤔
@krhd6817
Жыл бұрын
@@hobbyelectroniccircuits7391 uska matalab
@vashuelectronic3826
Жыл бұрын
Sir 5 channel Daigram ka photo bhejiye plz help me
@hobbyelectroniccircuits7391
Жыл бұрын
There are 8 outputs in CD4015 circuit. What if get 5 outputs from CD4017..?
@led9552
Жыл бұрын
kzitem.info/news/bejne/qYiMyGWZb3ymeZg
@malkanthiasoka1871
10 ай бұрын
Ruwan
@ayushmansarangi8260
Жыл бұрын
Bro whenever i am trying to make this in zero pcb its not working 😢
@hobbyelectroniccircuits7391
Жыл бұрын
Which circuit ? CD4017 or CD4015 circuit ?
@ayushmansarangi8260
Жыл бұрын
@@hobbyelectroniccircuits7391 cd4017
@hobbyelectroniccircuits7391
Жыл бұрын
What you experienced? Only one LED is lighting or all are not working ?
@ayushmansarangi8260
Жыл бұрын
@@hobbyelectroniccircuits7391 bro only one led is lighting
@hobbyelectroniccircuits7391
Жыл бұрын
So the problem is in NE555 pulse generator. Check its connections with my diagram or replace the IC.
@rajendersharma6234
Жыл бұрын
यह तो नॉर्मल है किसने इफेक्ट कैसे डालेंगे एक वीडियो बनाकर डालो
Пікірлер: 109