Stick to building m8 that roof degree is far too low for any tiles
@fuzzzeballs
3 жыл бұрын
pitch and guage if it's right now leaks but house concrete tiles are shit, I hate them
@Hew.Jarsol
10 ай бұрын
It must be the fish eye camera lense.
@winnieman-fx1hu
6 ай бұрын
they look level😂
@illmitchjax
2 ай бұрын
What pitch do you think it is??...
@Joe74854
12 күн бұрын
Those. Edge tiles should come off ,prime the back edge with cement and sbr also prime the under cloak verge ,then bed the tile with 3 sharp sand / washed grit and 1 part sand to 1 part cement ,add bit of Feb and a dash of sbr ,those verges should also have a mechanical fixing if no verge clip. Also no batten end protection that mortar will get wet and eventually rot the battens
@Rogerdodger-z7x
2 жыл бұрын
Professional roofer here: Everyone watching this, please remember this guy isn’t doing it correctly, the roof pitch looks too shallow & verges should be bedded not pushed mortar in with bits of rubbish here and there, this verge will fall apart in 5 years as there’s isn’t enough mortar in there. The video shouldn’t be followed for educational purposes & the chap doing the work should make this perfectly clear. Also there should be lead flashing fitted to the wall abutment at the top of the roof not cement layed on top of the tiles, any movement in the building & this will crack and cause a leak. Not to mention the batten at the verge shouldn’t be close to edge as it is in this video nor should the roof membrane be so close, all this will suck moisture through the cement verge & cause rotting.
@BuildingwithBudd
2 жыл бұрын
Frankie , if you listen on the video I did explain that this is a temporary set up , it was the best cost option for us at the time, we had tiles left from another job, I didn’t want to spend money on a proper flat roof, also I explained that you would normally fit lead over the cement at the point of meeting the building, I can’t disagree with what say, the next chance we get to film a roof we will then you can see what we are about, the whole building will be flattened in the near future, many thanks for taking the time to watch and comment, Cheers from Old budd 👍
@richardgrant7055
2 жыл бұрын
@@BuildingwithBudd Good traditional builder - balls it up AND still got an excuse !!
@hughrodgers5171
2 жыл бұрын
Would you put water proofer through your mortar mix
@dugegg
6 ай бұрын
This is wrong but when bedding verges with a pan tile I do like to throw some muck down first, squash some broken tile in, then out more muck on top. Them pantiles can be a right pain to point up because the bed is so big. I find that helps
@longandshort6639
26 күн бұрын
100 agreed - this video is how NOT to do it.
@JJ-jh6hz
3 жыл бұрын
What pitch is that roof lol looks too shallow for the headlap you have on the tiles, let me guess you battened it out at the max gauge?? 😂
@Tokaisho1
Жыл бұрын
I think it's an illusion with his camera work as it looks better at the end of the video when looks at it from the ladder lol
@coggsy3036
3 жыл бұрын
Right cowboy job fair play
@perfektrepairs7934
3 жыл бұрын
Only roof for that pitch is a flat roof, will leak like crazy with them tiles, why use a cement fillet on the back should be a lead flashing chased into the wall. Cement works nice but you are no roofer sorry
@loganrose.9209
3 жыл бұрын
100%
@Skols-se7jn
2 жыл бұрын
👍😂😂😂😂
@adymoore132
2 жыл бұрын
Just realised he is serious. Even funnier. Mate give it a break. 😂😂
@freakyscumbag
3 жыл бұрын
I wouldn’t be able to live with myself doing work like that, them tiles should be bedded ,everything is wrong with the felt and under cloak, ,and that lead work at tops a classic??? But I must admit that it would make a great education video ,,for how not to do it
@frankiedancaster4424
3 жыл бұрын
I never liked lead anyway
@sorryrocco
3 жыл бұрын
Your supposed too bed the verge tile onto a bed of compo, then point it up when the first lot has gone off.
@Hew.Jarsol
10 ай бұрын
Compo?
@sorryrocco
10 ай бұрын
@@Hew.Jarsol compo, composite another name for mortor. Sand & cement.
@markbucsenac5835
2 жыл бұрын
I've never seen anything like this in my 16 years of roofing, bed the verges, put a flashing at top edge, most importantly that roof is basically flat, board it and fibreglass, that's a leak waiting to happen
@magpie73
Жыл бұрын
I think this guy got the word old boy mixed up. Should say cowboy 🤠
@louiscurtis1334
3 жыл бұрын
Cowboys🤠 verge tiles should be bedded down not just pointed and putting broken bits of tiles in won't last 12 months
@frankiez7414
10 ай бұрын
Should have used sharp sand. Also what happened to the lead flashing ? I wonder what it looks like now ?
@andrewcooke3806
5 ай бұрын
Wow just wow, the tiles are wrong for the roof pitch, that pitch looks about a 10 degree roof which should be a flat roof, and as for the cement I’ve never seen anything like this, wow
@paulleigh5351
2 жыл бұрын
This is not the way to “bed” verges. A proper roofer would not do this. Calling you a cowboy would be an insult to cowboys.
@robertcaswell3914
2 жыл бұрын
Should have let the dog run that verge
@nickbremner6274
3 жыл бұрын
You're a good all-round bricky Mr Budd, keep uploading interesting videos of your work.
@merrickyusuf2341
3 жыл бұрын
You prolly dont give a shit but does anybody know of a tool to get back into an Instagram account?? I stupidly lost my account password. I love any assistance you can offer me
@kylendonovan9470
3 жыл бұрын
@Merrick Yusuf Instablaster :)
@merrickyusuf2341
3 жыл бұрын
@Kylen Donovan Thanks for your reply. I got to the site on google and Im trying it out atm. Looks like it's gonna take quite some time so I will reply here later when my account password hopefully is recovered.
@merrickyusuf2341
3 жыл бұрын
@Kylen Donovan It worked and I actually got access to my account again. I am so happy:D Thanks so much you really help me out!
@kylendonovan9470
3 жыл бұрын
@Merrick Yusuf happy to help =)
@Joe74854
12 күн бұрын
Lol I thought you were taking the p1ss till I watched the muck fillet omg your not getting paid to to this 😅surely
@BB-tx8ty
3 жыл бұрын
Quickest way is to take the tiles off then put your muck in then placing tiles back, so essy and simple, the tiles have more compression as well so it's stronger!
@stevesmith3850
3 жыл бұрын
Just what I was going to say,bed the mortar high and then press the tile on,the times iv seen people bed the tile on then they scrape it back and point over another day only to find in a year it falls out cos its only half inch think
@BB-tx8ty
3 жыл бұрын
@@stevesmith3850 it takes a lot longer that way and it's less strength as theirs no compression from the tile into the muck! UK Construction industry has gone backwards in a lot of ways, power tools make workers look better than what a lot of people think
@breadmanted
2 жыл бұрын
Why not do it properly ??? Bed the tiles in ,,rake back and flush point when it's set!!! To many ROOFER'S not doing it right these day's
@BB-tx8ty
2 жыл бұрын
@@breadmanted As I've stated my way doing it you pack in as much compo as possible for the tile to be placed back down again, this way the muck spreads out and force the muck back in again with a gauging trowel how I do it then angle the muck flat to the cement board, muck has to be a little stiff but workable, I see loads of guys packing muck in without taking tiles off which takes them all day to do when it should be done in less than half that time, UK construction industry has went downhill big time, big guys earning huge profits off the working man, not enough older guys taking young people on and when they do they use them as labourers for cheap pay and don't learn them much! 10 years time the UK building workforce will have lost a lot of people and a lot of knowledge how to do things because of greed
@kevincasson9848
2 жыл бұрын
Your talking shit! Cowboy! The man is perfection personified!!
@paulripley4095
Ай бұрын
Temporary job useing up left over materials what a joker we all know this isn't a tempory job its just cowboy work
@whitwoodkidwhitwoodkid9794
Жыл бұрын
meant to bed the verge then compress the tile down then point it off pushing cement in like that won't last plus your underlay should be under your cloak, plus the pitch of that roof you've used the wrong tiles or you need mor than 75 mil head lap
@smtsoftwaresolutions1966
2 жыл бұрын
I hope that's your own property, if not there will be a very unhappy customer when the fillet cracks, the end tiles blow off in a moderate wind and the felt rots in the gutter. I would also question the pitch of the roof for the tile used.
@BuildingwithBudd
2 жыл бұрын
Just to put you in the picture it is our own place and it’s just a temporary set up , we had the tiles spare from another project so we used those instead of a fibre glass or rubber roof, I did explain that it was only temporary and no lead as it’s not going to be there long, you are totally right in what you say, it is just a way to get to another point, really appreciate you watching the video 👍👍
@stevegreenly2259
Жыл бұрын
Where to start? 1. Membrane should be under the undercloak not on top. 2. Where's the felt support at eaves level? No membrane should be be fitted into the gutter. Also the first course is drooping - I suggest no eaves ventilation has been fitted. 3. Nails? I can't see any nails in the top row, which makes me think there are no nails fiited at all. 4. Roof pitch? The roof seems far too low for a single concrete pantile. 5. You should not mortar into an abutment. There should be a dry abutment fitted and / or lead flashing
@jasonjaques9421
2 жыл бұрын
Lol just take the tiles off and bed on properly 🤠🤠
@labbo5591
3 жыл бұрын
How long do you guarantee your work, 1 or 2 weeks🤣😂😂🤣 what a bodger!
@BuildingwithBudd
3 жыл бұрын
This particular job I have given a lifetime no quibble guarantee, that’s how I rolled that day, 😀👍
@paulmilbourne1
2 жыл бұрын
How not to do it .. bad bad work
@MrCamgavin
2 жыл бұрын
Should of been a flat roof. Way to shallow for roof tiles 😂
@Alexxx---101
7 ай бұрын
Thats not how you run a verge and why didnt you install lead flashings 😂
@Lktbh
6 ай бұрын
Not been funny but that pitch is too flat for them tiles you would of been better putting a rubber flat roof or a glass reinforced plastic roof that’s actually illegal what your doing
@BuildingwithBudd
6 ай бұрын
It was a temporary job , and this was the cheapest option at the time, had some tiles left from another job, it just served a purpose at the time 👍 it was a lot cheaper than rubber or fibre glass and got us out of a muddle.
@JeffersS13
10 ай бұрын
Shite! Tiles not bedded on to the mortar, felt on top of the cloaks, and lath ends in the mortar 😵💫
@rickphillips5098
Жыл бұрын
You disrespectful person to old boys ! Your work is shocking
@donal1982
2 жыл бұрын
Absolutely shocking job 🙄 As everyone has already said, the tiles need to be removed and bedded and felt goes beneath the undercloak. Timber roofs move too and that is why we use lead flashings instead of fillets. Your cement mix is too dry too, won't adhere properly.
@robinmuirhead2617
2 жыл бұрын
Excellent so you reckon it beats the latest Dry Verge Plastic efforts then lol
@callumking4471
5 ай бұрын
🤦🏻♂️🤦🏻♂️🤦🏻♂️
@FrancisLeamy
2 ай бұрын
Not all cowboys ride horses😂😂😂
@scarey260606
7 ай бұрын
Shocking to be fair so much wrong with this roof 😕
@pilotanimal192
5 ай бұрын
Polish it up , no cherry blossom will sort that out .
@eliteservices1509
9 ай бұрын
😂😂 pitch on that roof it’s gonna leak like a sieve.
@totsymanagwanhughes2183
27 күн бұрын
Why are you not bedding the tiles on one be one?
@chrisbels8568
3 жыл бұрын
The felt should go under the undercloak because the cement will now corroded it and now your mortar is set on a floating surface. The mortar should be cut to the underside of the tile and not up onto the tile face edge as it’s too thin, will crack and then open up the bed. Felt shouldn’t be going into the gutter too as it will rot out. The cement fillets at the top have been banned for years as the lack of movement and again will leak.
@sorryrocco
3 жыл бұрын
Your as bad as him, compo doesn't rot type 1f or modern felt.
@jerryd8107
2 жыл бұрын
@@sorryrocco And here is the problem with builders - no two agree on method. How is the householder supposed to judge whether the person they're paying is doing the job properly ?
@justbreakingballs
2 жыл бұрын
@@sorryrocco Why not?
@sorryrocco
2 жыл бұрын
@@justbreakingballs why not what
@adymoore132
2 жыл бұрын
Is this a comedy video. So much wrong. It has to be a joke. Made me laugh I must say. 😂😂😂😂
@Zackerzac789
9 ай бұрын
😮
@johnhorsfield1345
Ай бұрын
Would not let him build me Lego
@stuartwallace6306
4 ай бұрын
Keep an eye out for Indians.
@5eurocups2005
4 ай бұрын
Are the roof tiles suppose to be level? shouldn't they be slanted going down?
@jayashfieldmorris9938
4 ай бұрын
Gonna run out of mix there
@djm2333
2 жыл бұрын
Shouldn't be using those tiles on such a low pitch roof. 100mm cover and 20 degree or less pitch, by the looks of it. I wouldn't want you on my roof, that's for sure. Can't believe you posted this.
@jackbateman5849
Жыл бұрын
Never seen anything like it 🤦🏽♂️. Bed the tiles! Whats all the broken bits of tiles going in there for aswell 😂. Also that pitch is to shallow for them single pans.
@guitarpaul3645
Жыл бұрын
Thanks for the video. One bit of the job I was unsure about!
@BuildingwithBudd
Жыл бұрын
Cheers for watching
@paulperrin2152
3 жыл бұрын
What was mix3 to 1??, ifyeswhy ??, why no lead flashing on top row of tiles just a fillet ??
@aidanmccann7111
11 ай бұрын
Oh good god. Roof pitch is way too low for them tiles. So there was never a need to use lead for flashing just use mortar!!!. Has this roof been replaced yet
@Mrmrangel
2 жыл бұрын
😂undercloak under the felt.typical builder 😂what a mess.id have half of it done properly the time it takes you pissing around with one tile.
@Christopher-zt9eu
2 жыл бұрын
Speechless....absolutely horrific!!! Is this a joke?
@stuartsneddon6617
21 күн бұрын
What a mess
@danmartin6515
3 жыл бұрын
Love the birds mouth on bottom course lovely 🤣
@tgale3866
2 жыл бұрын
Should of fibre glassed it
@BuildingwithBudd
2 жыл бұрын
It was a case of using up what we had, it is only a temporary roof 👍
@rogermaynard2405
Жыл бұрын
Bed the tiles on. Once you’ve bedded them on you’ll be able to point them up. A much better job. Put some SBR in the muck and you won’t get any sag
@BuildingwithBudd
Жыл бұрын
Cheers
@ferenczsinko6770
2 жыл бұрын
Liked & Subscribed. Can I ask why you put the broken bits of tiles in. Is it for strength or just so I can use a bit less cement mix ? Storm Eunice took my verge tiles off so intend to replace using your video as a guide. Thank you for making this video.
@BuildingwithBudd
2 жыл бұрын
Ferenc we put the broken bits of tile to help the cement go of, if not it hangs wet for a long time, many thanks for watching 👍👍
@asroofingservices
2 жыл бұрын
Put a bit of rapid cement in with the mix that will help
@plaintiler
Жыл бұрын
If you put your verges back on the same way as this!......you'll be redoing them again in the future too
@TheTimutube
Жыл бұрын
@@plaintilerrubbish
@ifigeneiabamparatsa1498
9 ай бұрын
Hi, can you tell me please if it's working... thanks
@BuildingwithBudd
9 ай бұрын
It’s working fine , it is only a temporary solution, we were going to flat roof it but we had some tiles left from a previous job, it just worked out a lot cheaper option at the time, but in answer to your question it’s working fine 👍
@Ben201-k2e
8 ай бұрын
I can guarantee the verge will have cracks all over it as he didn't put a slight lip on the cement verge going under the side if the tiles, which makes the rainfall run straight into the cement and as I say causes cracks.
@leec7180
Жыл бұрын
A flat roof has more pitch than that .
@BuildingwithBudd
Жыл бұрын
Totally agree we did it as a temporary set up, as we had the tiles left from something else, it has 18mm ply underneath, but doing it this way was just so much cheaper and easier at the time, it did the job. Cheers for watching 👍
@LouisJudd
Жыл бұрын
cowboy
@7xJack_
3 жыл бұрын
Great work bud..you from norfolk?
@BuildingwithBudd
3 жыл бұрын
Thanks and yes
@BHP15
2 жыл бұрын
that is the cowboy work. you need tons of cement for that way of job.🤣🤣🤣🤣🤣🤣
@Skols-se7jn
2 жыл бұрын
Mate stop urself it's all wrong they need a proper roofer first take verge tiles off then bed each one then give it awhile for the muck to bond then point if I did that I'd retire
@Daniel-lk2gi
Жыл бұрын
I would be embarrassed to put that on KZitem..!!
@MeHim-d4j
3 ай бұрын
Shouldn't the undercloak be over the felt and not under??
@mick949
3 жыл бұрын
what a bodge i hope you paid the customer thats rough as fuck hardly any over hang on the gable
@rossko727
Жыл бұрын
This is how not to muck a verge! Take the tiles off then lay the muck then you put the tile on to the muck pushing it down for a nice bond, the way in the video will be loose and within a year or two
@tonyford5326
11 ай бұрын
Not really how you bed tiles but each to their own mate 40 years doing it
@rinzler9775
8 ай бұрын
Wall to top of roof needs flashing. That won't hold.
@Skols-se7jn
2 жыл бұрын
Pointing shocking Ur ment to see the side of the tile stop it you give us roofers a bad name
@ciebrown1639
5 ай бұрын
No lead flashing where the roof meets the house?
@Batman111-q3r
9 ай бұрын
Use a margin trowel, and a ridge trowel
@vinceskinner9357
Жыл бұрын
That's going to piss in water, dont do your roof like this. total bodge up in sooooooo many ways
@louie.vision.5255
Жыл бұрын
How?
@vinceskinner9357
Жыл бұрын
@@louie.vision.5255 Ok where do i start? cement butted up against dry pebble dash render is a good a place as any i suppose. given that the render is pebble dash tells me its going to be quite old mid to late 80s the cement when drying will shrink as it looses its moisture this will pull inwards in all directions, this will include pull away from the wall witch is dry meaning the cement is not sticking to the wall its sticking to the dust and grime so when drying accrues the bond its not great. all this will allow water in-between the wall and the cement. Then factor in the seasons doing there bit on the cement it will eventually move and crack. Best way would have been to flash it. Just my opinion
@stevenodonnell6318
2 жыл бұрын
Take the tile off and bed it properly with a decent amount of muck , cant just push it in, does nothing
@calvinwilliams8547
8 ай бұрын
Should bed tiles that will all pop
@maikdittrich5727
Жыл бұрын
Furchtbar....
@Presumin0Ed
2 жыл бұрын
Great vid :) Are you in Suffolk? I'm in Sax and three big bits of the concrete recently fell out of the verges (of my 400-year-old house). Almost hit me cat! :O ;) One of the barge boards is a bit knackered too :/
@BuildingwithBudd
2 жыл бұрын
Old Norfolk boys , don’t get over the border much, cheers for watching 👍👍
@jacksmith4484
Жыл бұрын
Your not a roof tiler by trade I take it
@6571sid
Жыл бұрын
Definitely not a roofer
@plaintiler
Жыл бұрын
😂where are your horses?
@jagsmith9565
2 жыл бұрын
Completely wrong mate
@kennydieu2694
2 жыл бұрын
Thanks for sharing
@nonsheep5823
3 жыл бұрын
Looks shallow pitch ? Lower than 15* and your in trouble also head lap of tiles wellout of spec. Max is 100mm your on at 75mm , lead flashing needed to be chased into render, that mucks blown already ibet , still the customer would think it looks good
@jimralph8066
Жыл бұрын
Wonder did water blow up under the tiles 🤔 at this low pitch tiles should have a greater lap
@seanwalker1972
2 жыл бұрын
Alot of ppl saying should be beded and I agree but try do a regent tile 1st looool you need to use very stiff muk otherwise youre having a bad day
@johnbowkett5920
3 жыл бұрын
That pitch looks bloody low ???
@BuildingwithBudd
3 жыл бұрын
It is very low. However the building is only temporary
@johnbowkett5920
3 жыл бұрын
@@BuildingwithBudd ☺☺☺☺🙂
@raybans8712
3 жыл бұрын
@@BuildingwithBudd why spend the extra money on tiling it then A tiled roof costs more than a flat
@maikdittrich5727
Жыл бұрын
So wurde vor tausend Jahren gebaut...
@pi561
3 жыл бұрын
That is NOT how you bed verdge tiles !!!
@rokalot2436
3 жыл бұрын
I agree what a fu#$ing mess ,should take off verge tiles and BED THEM 🤪
@rokalot2436
3 жыл бұрын
Where's a roofer when you need one,
@michaelgray9234
3 жыл бұрын
Rough has
@BuildingwithBudd
3 жыл бұрын
Chaps before you beast me , it is a temporary set up, give us a break 😂😂
@danmartin6515
3 жыл бұрын
I’m a roofer of 15 years personally with such a big bed i would bed and point dental slips on to half the size of the verge stops cracks etc
@gavinmountjoy7459
2 жыл бұрын
hurt my eyes watching that wow a how not to do it tutorial
@donaldmorrison6147
2 жыл бұрын
What on earth is going on here
@big.a1131
2 жыл бұрын
Not enough pitch driving rain will piss in
@paulcollins6221
2 жыл бұрын
It will crack first hot day
@paulgale9872
2 жыл бұрын
Why have you got tiles on a basically flat roof and you bed tiles into the compo not pushing it in like that there's so much wrong with that I don't know were to start
@BuildingwithBudd
2 жыл бұрын
Paul You totally right, but it is a very temporary roof, we used up some bits and pieces we had left, we could do the job ourselves, and we didn’t have to pay a flat roofer, it’s a means to an end, many thanks for watching 👍
Пікірлер: 223