Thanks for your important guide to Centurion Motor gate controller!
@ashtonchetty4408
3 жыл бұрын
Installed a motor thanks to this video
@selepemoetapele8787
Жыл бұрын
Just sorted my issue....appreciate lots
@TemeAregay
7 ай бұрын
Nice explain
@mbulelophakati7101
Ай бұрын
Wooow.......thanks a lot🤝🏽
@dangerousdrful
5 жыл бұрын
thanks fr the video ..gate was stuck..didnt know hw to put on manual...till now:)
@CenturionSystems
5 жыл бұрын
It's an absolute pleasure, Dane! So glad that we could help :-).
@emzinitechnicalservicesemz1265
2 жыл бұрын
Nice lecture, mind opening, thank you so much
@rickynaidoo2921
Жыл бұрын
How is the bracket fitted around the gate motor opening and closing with the key?
@moisebagumandihano2710
Жыл бұрын
I have a D5 evo motor. I have checked all the mechanical limits and followed all instructions. The magnet is also well set but when the motor starts for the first time, before it finishes the full cycle the controller goes off then restarts itself and everything starts over. Can you please assist?
@uniquebayus8951
8 ай бұрын
Check the battery if it's fully charged
@energymangisi1934
Жыл бұрын
well explained
@paulkishwaliaula1533
5 ай бұрын
Awesome
@Grant-kj4eq
4 жыл бұрын
Very good detailed instructional video .
@lucyhaviga5400
8 ай бұрын
When gate opens it rolls off the rail and falls over , does this have to do with the settings on remote control ?
@teched9956
5 жыл бұрын
Very good video.
@ebrahimtait6481
8 жыл бұрын
Hi , I have installed a D5 Evo some time back but have had issues with the gate opening randomly on it s own. This causes problems for my security company as they are unable to access the premises via the Air Keypad ......when I activate the holiday lockout .
@Spholamagates
7 ай бұрын
My gate motor doesn't want to go to manual D5 Centrion, even when i screw in the knot , it does not want to tighten up, What could be the problem
@phumeoli
2 жыл бұрын
Hi. I have a problem opening the cover. It is stuck on the side of the gate and also where do I find the power switch. thanks.
@thapelodubeg
3 жыл бұрын
Impressive
@koolabraham1510
5 жыл бұрын
this is really good have you extended this type of gate to Africa especially to Kenya
@centuriongateskenya7904
3 жыл бұрын
Yes we have them in Kenya. Both swing and then slide
@crystalshaddy9247
2 ай бұрын
❤
@shonalsaiah9270
8 жыл бұрын
hi thanks for the relpy
@daryldurward6155
5 жыл бұрын
hi . my d3 opens at the intercom inside but not with my remotes. please help
@ibelongtojesus2134
3 жыл бұрын
Hi sir I have one question if the motor not reached to moto must be what, only in the motor there's power
@edwinmuhavi246
4 жыл бұрын
very clear
@Music-rs3hp
3 жыл бұрын
Installation instructions of the D3,D5 sliding gates.
@elton-thailand4899
7 жыл бұрын
Awesome!
@rock882josh7
7 жыл бұрын
hi. I have the D5 evo. I have black and red plus ground pillar light cables. I need help how to connect these cables to the controller? currently these are loose in my box and I want my pillar lights to work
@martinlourenco831
3 жыл бұрын
Why does the gate open half way and it stops
@BMTVSA
8 жыл бұрын
I have a problem with my Motor it only works when i press the test button, when i try to set my reciever it doesnt have life does the black small cable have to not be connected anywhere
@CenturionSystems
8 жыл бұрын
Hi there. Thanks for your query. No, the thin black cable is the antenna, and doesn't have to be connected to anything. The programming method would depend on the model of receiver/remote that you are using. Kindly give our technical support team a call on 0861 003 123 so that we can help you diagnose the problem.
@BMTVSA
8 жыл бұрын
Ok thank you
@gertvanwyk1976
4 жыл бұрын
Thanks
@martinlourenco831
4 жыл бұрын
Why it keeps open when the program has been done it doesn't stay closed
@BOBBY-et9xb
3 жыл бұрын
How to check oil level on dip stick for d5.
@mbhekisenisibiya2619
3 жыл бұрын
Good afternoon. My gate cannot find origin. What to do?
@felixmwanza4678
7 жыл бұрын
Hi Iam an end user and recently installed a D5 Evo gate motor. Would you please help me with the guidelines in connecting a Commax intercom to the gate motor
@interestwood
9 жыл бұрын
i installed a d5 motor for a client, it works perfect except that the gate moves too slow till it crosses the origin marker plus after opening, the gate shifts back slightly as if it wants to close again and stops. what could be the problem.
@CenturionSystems
9 жыл бұрын
George Oduro Hello George. The gate will move slowly until it knows its position (by moving the magnet past the origin sensor), so that is normal. There could be a couple of reasons that cause it to want to move back after opening - such as detecting a collision. Please give our Technical Call Centre a call to help you identify what could be causing this. The number is +27 11 699 2481.
@interestwood
9 жыл бұрын
CenturionSystems alright thanks.
@fahiemmccallum4803
7 жыл бұрын
the gate lying on motor
@hassantiamiyu8748
7 жыл бұрын
George Oduro send your contact
@adamjohannesbarnard5518
Жыл бұрын
Hi my d5 will nie oop of toe maak nie wat kan vout en waar na moet ek kyk help aseblief
@hoquan1626
4 жыл бұрын
hi, I am going to build the gate but I don't know how to install opener so I need help, thanks kevin
@dharmeshpatel1437
4 жыл бұрын
Hi my master remote is working but my other remote not setting up so please can you help me to how to set up bcs I try to hold 15 sacend master remote after I am pressing normal remote but not seting up
@zuksyselekisho
7 жыл бұрын
the motor is only closing when i press test button but not opening
@CenturionSystems
7 жыл бұрын
Please contact our Technical Call Centre for advice on +27 11 699 2481
@arthurkays8200
7 жыл бұрын
Hi, kindly assist. My D5 gate motor shows that it has stalled and when I try to reset the it by setting the gate limiters it says no origin found! Whats the correct procedure to unstall or reset it?
@CenturionSystems
7 жыл бұрын
Hi Arthur. Thanks for your message. Kindly give our technical helpline a call on +27 11 699 2481 or send an email to support@centsys.com. Our knowledgeable technicians will be able to assist you with some diagnostic procedures.
@samuelogundare3864
7 жыл бұрын
Hi, please I will to get info about price and supply. Pepersonaltrainer or 0793775847 samuel
@AlfonziaGarrett-d4v
Жыл бұрын
5:21
@thabomajola6209
2 жыл бұрын
Good people please always remember all these are man made so don't be intimidated
@teresalangenhoven7712
4 жыл бұрын
if my master remote is missing, do i reprogram everthing? and how?
@hasiburrahman5177
3 жыл бұрын
ok no problem this jumper open or dip baton 30 ascend or remote dip push
@musatajudeen5349
5 жыл бұрын
HI centurion i want to be a distributor in Nigeria and as well install.
@rogerhicks481
6 жыл бұрын
I have a electric sliding gate it works ok for about 20 times then it goes past stop sensor for no reason then I have to reset it again anybody got any ideas
@gregoryeiaseb9179
5 жыл бұрын
how can i slow down my gate
@mileswilliams7718
8 жыл бұрын
Hi I'm an end user and wanted to know how would I go about programing new controls if I have lost my master control? Thanks
@CenturionSystems
8 жыл бұрын
+Miles Williams Hi Miles. Thanks for the comment. If you have lost the master, you need to clear the receiver's memory by bridging either J1 or J2 with the middle pin. This will delete all remote buttons. Next, press and hold the remote you wish to make the new master for approximately 5 seconds. Once you have created the new master, press and hold it again for 11 seconds, release it, and then systematically press and release each new button that you wish to learn. Alternatively, you can give our tech support team a call on 0861 003 123. They will walk you through the procedure.
@mileswilliams7718
8 жыл бұрын
Thanks for the help. I appreciate the quick response. Will give this a shot and see
@CenturionSystems
8 жыл бұрын
+Miles Williams Awesome! It's an absolute pleasure. Please give us a shout if you don't come right.
@vtsielectrical3727
7 жыл бұрын
please help how to erase the nova remote from the d5 gatd motor
@CenturionSystems
7 жыл бұрын
Please contact our Technical Call Centre for advice on +27 11 699 2481
@ajayimatthew9093
7 жыл бұрын
How do I download this video to my phone
@zuksyselekisho
7 жыл бұрын
hi i am Theo instruggle I struggle to link the remonte with my motor need assistance
@CenturionSystems
7 жыл бұрын
Please contact our Technical Call Centre for advice on +27 11 699 2481
@chilubamanduli9375
7 жыл бұрын
GOD IS OHSOME
@rasheedmuthukodan5179
2 жыл бұрын
Hi
@vivianamoya875
6 жыл бұрын
No hablo english y tengo problema con la instalacion de un motor D5 , parte y se para y el visor LCD me dice error en Fuente de Poder, Me puee ayudar alguien
@alejandrourizar6405
6 жыл бұрын
Estimada Viviana. Podria enviarnos su direccion email e indicarnos el pais desde donde nos esta contactando?
@yimmyfraile
4 жыл бұрын
tienes un problema en el cargador, posiblemente este dañado, debes reemplazarlo y listo. o tienes un cable flojo entre la fuente de poder y la tarjeta logica.
@joaquinvillarreal8745
4 жыл бұрын
Por favor lo pueden decir en español
@raulmartinez2906
3 жыл бұрын
Español, Spanish .
@thiara62
8 жыл бұрын
Bonsoir j ai un problème sur mon motor centurion D5 quand j utilise mon télécommande ou le bouton Exit pour démarrer mon motor l écran affiche No limits SET
@titoreis272
3 жыл бұрын
great video and helpful
@jonathanmitchell9509
4 жыл бұрын
Thanks for the instructional video. I managed to replace my old battery and reprogram closing limits. Thanks for saving me a call out and the hassle of getting a repair person.
Пікірлер: 83