Best fiberglass tutorial I've seen yet on KZitem, this guy is a good teacher
@bradleyplummer5778
2 жыл бұрын
Needing to make panels and such at work. This video has helped a TON for me to create the molds. Plenty of good information within the video! TY!
@a11an72
3 жыл бұрын
Tnx man , these are great videos for amateur diy'ers like me , the endresult on the followup video to this is exactly what im after .... best wishes from Norway
@liamodonnell469
2 жыл бұрын
So well explained Well done
@OMEN-TV
4 жыл бұрын
THANK YOU VERY MUCH FOR THE LESSON! i was searching hours on youtube for a tutorial like yours.But mister i really respect you health came first,please use a mask when working with fiber/polyester.Great video again!
@shahrulziman7752
2 жыл бұрын
The ultimate teaching video
@maqyotvblog
3 жыл бұрын
very thanks, this tutorial is very clear. i hope others can see this video.
@chuckeynewkirk199
2 жыл бұрын
Good video love the details
@premnakarmi2580
3 жыл бұрын
Thanx for making Small fiberglass mound in detail.but how to clean after using brush plz ?
@SkylarkCamperAdventures
3 жыл бұрын
Brilliant tutorial, learnt a lot from that 👍🏻
@sidheshchari154
9 ай бұрын
Nice work sir
@josuedeasisjr2140
2 жыл бұрын
How long before you coat the resin on top of the gelcoat ?
@glengullickson6538
Жыл бұрын
Looks like that is all done with polyester(?) Can the same scenario be done with epoxy? Thank you.
@stevew6141
2 жыл бұрын
Great video, can ova be used as a barrier between the plug and the gel coat? Thank you
@frankpineda1832
5 жыл бұрын
Wow beautiful work 👍
@seechurndinesh9710
Жыл бұрын
How many minutes should the gel coat dry to apply the fibres?
@61riaz
4 жыл бұрын
Wow really amazing idea can shared
@glengullickson6538
Жыл бұрын
Did you let the first gelcoat kick off before applying the second?
@jernejp7579
4 жыл бұрын
Hi CFS, Like your videos on you tube, very useful and detailed, thank you for your contribution. While watching this video I was wondering what is the green base material of, where the model is attached on?
@ShabirAhmad-oe3dq
2 жыл бұрын
Lemineshan mat is the Epoxy resin
@Pushyhog
3 жыл бұрын
try mavcoat release if ya want the best. Part will fall out, Boeing buys it by the 55 gallon barrels.
@TimPalfrey
Жыл бұрын
Is this guy using polyester resin without a respirator?
@berniestorr5508
7 жыл бұрын
Hi Paul ,If you use the mirror glaze release wax do you also have to use the spray on PVA release agent befor you gelcoat
@garyengland5326
5 жыл бұрын
No, but using pva gives an extra layer of protection. But, the mould will need wet sanding and buffing, because pva doesn't go on perfectly smooth
@garydeandeery
2 жыл бұрын
I can never get the mix right I only do small mixes and don’t even get 5 mins till it’s going off Say if I do 20 mils do I do 2 drops of catalyst. Coz I’m doing 0.5 in the syringe and don’t have any time to work with it I did 50 mils before with 1 on the catalyst and then it was not going off was sticky still so I went over it with epoxy resin
@AutoFreak10
2 жыл бұрын
Could I ask how you would recommend making a tunnel for my steering arm to pass through? I had to cut a hole in the fibreglass to allow the steering arm to enter but although not that important as it only goes into a well, I was wanting to make a fibreglass tunnel for it but there is lots of bends and shapes that would be required for the surface part before it enters into the tunnel.
@bazzarr
10 ай бұрын
Fiberglass ASMR.
@audiesalminao3635
Жыл бұрын
Amazing
@chamindanissanka1378
3 жыл бұрын
Best job sir,
@adamcatlow7496
3 жыл бұрын
Would this work with my Europe dinghy
@chandrashekhardeshmukh4887
4 жыл бұрын
which jel coat useing
@sakibian01
5 жыл бұрын
polyester resin?
@user-fb9wl8ip6p
5 жыл бұрын
What matarial used can you talk me please please please
@rct2
2 жыл бұрын
Great video but can I ask how long between each layer of glass did you leave it?
@sunilkumararickattu1845
5 жыл бұрын
Sorry to inform you that did not mentioned what grade fiberglass mate use [first/light weight thjn mat] prior to second lair of 450 csm mat and ratio of MEKP using with. That is very important in a professional manner?
@BlackHearthguard
7 жыл бұрын
How would you mold a hull that has a tumblehome in it? Is it possible to do it this way?
@johnrutherford8246
4 жыл бұрын
If it's a coble shape, you need to make a two piece mold. It's the only way.
@suragvs2870
3 жыл бұрын
I am looking fiberglass job any vacancy in your company
@Rick-tb4so
6 жыл бұрын
Well done......What is the name of the 1st mat you applied to the mold ??
@garyengland5326
5 жыл бұрын
Surface tissue
@dantheman321
5 жыл бұрын
@@garyengland5326 do you have to let the surface tissue layer dry before you add chop strand or can you work straight through ? Many thanks in advance
@mohamadnaeemgurchani5898
5 жыл бұрын
best .thanks
@harrydavepagaoa4709
6 жыл бұрын
hello, what if I did not put gelcote, will it work??
@abraomunguambe7949
5 жыл бұрын
i would like to know where can buy unmolding oil for resine
@abraomunguambe7949
5 жыл бұрын
Or what is the exactly name of unmolding oil?
@michaelrommedahl525
6 жыл бұрын
Powder- or emulsion- bound Mat...???
@garyengland5326
5 жыл бұрын
Emulsion, powder is for epoxy, emulsion is for polyester
@simonac688.
2 жыл бұрын
wow 👍
@bangsabar3689
Жыл бұрын
Good👍
@DINHVANTAM-QTRI
3 жыл бұрын
Hello
@patrickhall1532
8 жыл бұрын
Looks exactly how i pulled mine out seeing as this is my boat plug😂
@doranagedoranage1651
2 жыл бұрын
👌👌❤️
@ShabirAhmad-oe3dq
2 жыл бұрын
Leminesh polyester resin Epoxy resin
@298CRE8
7 жыл бұрын
If your viewing this don't take what he says as gospel and watch other vids this is ok for basic techniques and fibreglassing but not anything else find better vids or research more plenty out there 👍
Пікірлер: 56