Just bought my NH275 last fall. It has six haydogs. 4 of the 6 were either rusted in place or broken springs - thanks for the great video
@christopherpyle3503
11 ай бұрын
As always, thanks for the videos. You explain things very clearly. Have a nice day.
@TheScientistHayFarmer
11 ай бұрын
Thanks man, I really appreciate it and glad you find some value in it.
@jeffferanec4526
4 ай бұрын
Great content Mr.Scientist, the hay dog function is ever so important, I spray my hay dog pins w/ a shot of penetrating oil every other time I grease the baler.
@Dave-ll6ei
11 ай бұрын
Thanks for the information on the hay dogs.
@bobcole9274
11 ай бұрын
Good video. thanks
@vincentmeyers914
4 ай бұрын
Super helpful. Where did you purchase the new springs.
@TheScientistHayFarmer
4 ай бұрын
Messicks, New Holland Rochester, or your local dealer.
@cathymuehring893
10 ай бұрын
Do you think shimming the wedges with washers would help when baling light hay ? How many washers ?
@TheScientistHayFarmer
10 ай бұрын
It might? I’ve never tried it. In fact, I don’t even use wedges in my baler. Try it and see what it does. Maybe just add a few washers to start.
@bigr0075
9 ай бұрын
Had to use a ball joint separator and impact gun to get the pins out.
@cathymuehring893
11 ай бұрын
i will check my dogs but I wondered about twine tension also. MY 268 makes great bales and ties everytime but I put in new twine for 2nd cut with very light winrows. The bales came out very loose, would almost fall apart. cranking it down only made bales heavier, still to loose. I hope its just the hay and not baler.
@TheScientistHayFarmer
11 ай бұрын
Unfortunately that’s the draw back with light soft hay. Second cut is shorter and finer. Increase your baling speed to feed the baler faster, and if they make wedges for the bale chamber of a 268 those will help with tension as well. Faster ground speed will help more than anything. I bale 5 mph in light hay to keep my 311 fed.
@cathymuehring893
11 ай бұрын
@@TheScientistHayFarmer When I went faster the pickup would skip over and leave hay on the ground. Thanks for your very good videos.
@TheScientistHayFarmer
11 ай бұрын
Then the next step is to make sure your hay dogs are good. If they are, then you’d benefit from wedges n
@cathymuehring893
11 ай бұрын
@@TheScientistHayFarmer I have two dogs on top and bottom and six wedges.
@4schitzangiggles
Ай бұрын
On second cut I'll combine 3 rows into one to have a nice fat consistent row that keeps the baler fed and nice tight bakes. Did that with my NH 278 and now with my NH575. I have an LS MT7101cps and I can tailor the ground speed to match the windrow far better than with my old Case 930 which was either too fast or too slow
@brittanynorris2297
3 ай бұрын
Thoughts on a NH 269 that won’t tie?
@TheScientistHayFarmer
3 ай бұрын
That’s like asking “why won’t my car start?” There could be a lot of reasons why it’s not tying, and depends how it’s not tying as well.
@4schitzangiggles
Ай бұрын
It might be out of time, have a bent Needle arm ... Or a hundred other things wrong with it.
Пікірлер: 20