Killa video! But also learn this on forum... ,the axels on drum brake trucks are about 1/4" longer then disc brake axles,so the brakes won't line up with out spacers..
@chrismcfarlane7029
2 жыл бұрын
Very help full. I was gana swap the whole rear end out but for that my bag brackets are welded
@savagepickle0443
Жыл бұрын
I did a read end swap from a late 90s blazer with a lsd, definitely worth it but still has drum brakes so I’ll be swapping those very soon to the 2000 disk brakes. LSD blazer rear end is a must in my opinion tho and you can find one at your local junk yard for dirt cheap!
@justin_meshell87
Жыл бұрын
Yeah I am on air also and didn't want to go through the trouble of reconfiguring the blazer axle.
@manyfaces2614
13 күн бұрын
Part numbers would be nice
@chucklaneChuckylane
Жыл бұрын
I wasn't aware of the e brake cable, thank you. I'm using the entire rear end from a Blazer, the only difference that I know of is the overall width of the rear end, it's a little bit wider than the pick up, but the pins line up, so it's a smidge more stability is all it comes down to on my truck, it might not be the same for somebody who cant get any closer to the inside of the fender wells due to a wider tire but there's a grip full of room before you'd be rubbing the inside, I use 235/60/15 all the way around my truck, a little tight fitting on the front because of how low it sits in the front, but all sorts of clearance in the back. Do I need to switch out the proportion valve while i have your attention? And because i am using the rear end from a 4x4 and my '94 Sonoma / (looks like an S-10 with a GMC hood, I like the two lines more than one in the center) lol Are there unseen problems i'm heading into here because of the 4x4 thing ( fingers crossed big time now) Unless you're real quick to reply, i'll find out within a few days I recon because i'm real close to doing the swap as I write this. thank you for posting too, your truck looks tight, what I saw of it.
@johnshaddick6858
8 ай бұрын
I would have replaced both the axle bearing and the seal before reinstalling the axle in the axle tube.
@mikelovito5127
Жыл бұрын
fantastic video,I have a drag-street henry j with 92 S10 frame, with rear drums. That I want to convert to disk.., your ideas are perfect, I going to start gathering parts..Thanks
@Chrissutter35
Жыл бұрын
hey man if this works on you 92 that means this works on the 82-93 trucks as well, hit me up and let me know this would save me so much
@mikelovito5127
Жыл бұрын
@@Chrissutter35 I didnt build it ,but it works great, this is 100inch wheelbase, 10 bolt chevy rear added, he kept the p/s & p/brakes, he tilted the motor to the left 2 inches to clear steering post on chassis, I even put dropped spindles 2 1/2 bolt right up, rides great & handles like a new car
@manyfaces2614
16 күн бұрын
Make sure im tracking,i gotta 2000 sonoma sport. Could i do this same swap?
@nicktirado4318
Ай бұрын
So you had to shim out the bracket/caliper for wheel fitment ?
@chrisjohnson7097
Ай бұрын
What rear brake rotors did u use? Was it for a 2wd blazer? Where did u purchase?
@sgtsarcasm5603
Жыл бұрын
1. Will this work on an older s10 specifically a 97. 2. How much of the ebrake cable do you need like the whole thing. 3. Same question for the brake line to the caliper.
@justin_meshell87
Жыл бұрын
1. Yes! I have found that the rear end and frame are the same from 1994 to 2003. So this should work for your 97. If you want to be safe grab the rear brakes from a 97 blazer or Jimmy. 2. To be safe I pulled the ebrake cable from the caliper all the way to the front door. 3. The connection from the drum and caliper are completely different. So you will atleast need the back half. Good luck 👍 I will be making a follow up video of everything working when I finish painting the truck body.
@justin_meshell87
Жыл бұрын
Thanks for watching the video. I will be replying to everyone soon!
@MrARIVERAL
2 жыл бұрын
Great job man. Were you able to hook up the emergency brake cable to this setup?
@justin_meshell87
Жыл бұрын
Thats definitely what I am hoping to do. I will make an update video when I install it and what all is needed.
@mr.eervianlesmana9263
2 ай бұрын
@@justin_meshell87 is that a gm 7.5 10 bolt 28 spline rear diff?
@itza_red_panda2045
Жыл бұрын
Man I’m having trouble finding that anchor backing plate. Can’t find it anywhere. Specifically the one for that passenger side. I found it for the driver side but going nuts trying to find it for passenger side. Any chance you have a link to it?
@justin_meshell87
Жыл бұрын
I got mine out of a local salvage yard. But I will be on the lookout for one for you.
@user-ew3bp5os5x
Жыл бұрын
Hi, Can you send me or post where you got that brake kit. I like the way the back plate bolts on with 4 bolts. Looks clean
@Z-e-r-0
11 ай бұрын
from any part store since the 90s
@justin_meshell87
8 ай бұрын
I just went to the local wrecking yard and pulled the dust covers, backing plates, and e brake cables from a 2wd blazer. Then, went to O'Reilly's and ordered the rear calipers and brakes pads. The rotors are stop tech from summit racing.
@ethanbrattain9641
Жыл бұрын
Question? So all u pulled out of the diff was the 2 smaller gears and 2 c clips right?? Or did I miss something? I’m wanting to do this to my s10. Thanks for help
@justin_meshell87
Жыл бұрын
Yes, to get the axles out you will need to remove a 8mm bolt that is holding the pin for the spider gears in place. Then two c clips. After that the axles slide right out.
@340352
3 ай бұрын
Hey I have a question can you just replace the whole rear end that is already set up for disc brakes
@johnscreekmark
2 ай бұрын
Cut the Music…. It would help to hear what you are saying.
@susrides
Жыл бұрын
What master cylinder are you running? I swapped the drums on my 94 jimmy but need a disc/disc master cylinder, and have had a difficult time finding the right one
@Z-e-r-0
11 ай бұрын
called summit or Jegs. only been selling kits now with parts since the 70s
@justin_meshell87
8 ай бұрын
Im currently useing the factory master and booster haven't had any problems but i plan to upgrade to a 94 chevrolet Astro hydro boost
@sl5303
Жыл бұрын
Hello, I can't find the same discs as you (ventilate) if you can help me
@willwheeler4068
Жыл бұрын
Ebay drilled and slotted rear rotors for 99 blazer
@justin_meshell87
8 ай бұрын
The cheap route would be Ebay www.ebay.com/itm/153238598996?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=yucMq8wiS-G&sssrc=4429486&ssuid=JuE1eIFNQ8i&var=&widget_ver=artemis&media=COPY
@Robbys10xtreme
5 ай бұрын
What are the reason for the washers?
@BBradford1825
10 ай бұрын
🏎👍🏾
@remiel3315
Жыл бұрын
How thick were the washers you used to space out the backing plate?
@justin_meshell87
Жыл бұрын
I used two 5/16 washers per bolt about the thickness of a nickel. So eight per side. Sixteen in total.
@remiel3315
Жыл бұрын
@@justin_meshell87 thanks!
@dalwyson1
Жыл бұрын
Mine is sticking do I need a master cylinder to release the pressure
@justin_meshell87
8 ай бұрын
You might look at replacing or rebuilding the caliper
@elijahevans2224
Жыл бұрын
is it the same backing plate for side
@justin_meshell87
8 ай бұрын
No unfortunately, they are different
@Z-e-r-0
11 ай бұрын
yea. they make way better conversion kits then this junk. ones that fit correctly and don't need any extra supplies. and to the comments yall know this isn't something new right? people have been swapping 210 Truck and Balzer rear drums out sense the early 90s. If you need a KZitem video to do this, you are definitely not mechanically inclined at all and you need to turn your tool box over to your wife along with your balls to sell on Marketplace. somebody will put them to good use.
@justin_meshell87
8 ай бұрын
I see that you were born knowing how to do everything and never needed any help ever. Also that you can afford "the good stuff" Well, this video isn't for you my friend. I'm just helping and learning along the way. Good luck being a keyboard warrior, and I hope you speak to someone about your anger and negative mindset issues.
@goon4696
Жыл бұрын
So I have a 94’ 2wd 4.3 v6 Chevy s10 extended cab, I am wanting to swap the rear drums for the disc brakes, do I need the entire blazer rear end or just the axle?
@justin_meshell87
Жыл бұрын
I believe the easiest thing you could do is get the entire rear end and swap it in. All blazers, and Jimmy's are 4.3L v6. So the diff gears should be the exact same. But make sure you pull it from a 2wd! As a bonus they all also have a sway bar that you might be able to use. I know in Texas at pick N pull the complete rear end with disc is $172.00 and a core charge of $24.99.
@justin_meshell87
Жыл бұрын
But the cheeper way would be to pull just the brake parts out of a salvage yard and swap them on. Definitely the backing plates and the dust covers for sure. You could get the rear calipers from an auto parts store new for added reliability.
@damnitdang
Жыл бұрын
@@justin_meshell87 will 2wd drum ebrake cable work on the newer 2001 rear disc brake?
@justin_meshell87
Жыл бұрын
@What the phuck Unfortunately no. You will need the back half of the e- brake cable from the Blazer or Jimmy to do the disc swap.
@pleasantvalley9898
Жыл бұрын
Thank you so much brother!!!
@petergriffen5736
2 жыл бұрын
Started off good, but went to shit real quick.
@justin_meshell87
2 жыл бұрын
Where did it go bad? Im still new to making videos.
@willwheeler4068
Жыл бұрын
Fuck this troll man awesome video my first car ever was a 96 sonoma lowered and I totaled it and I'm just not getting around to finishing my s series childhood build except lifted this time. When I finish this I am gonna do another s dime but lowered
Пікірлер: 54