Glad I could help! And damn, sorry I didn't read this sooner! I'm currently replacing all the factory gauges with Auto Meter gauges. I threw all the factory ones in the trash. None of them worked. But I would have been happy to give you the clock for free. If you could make it work, great! If not, no big loss. I have seen them pop up on eBay every now and then. Thanks for watching! Best of luck to you!
@superspecial2
12 жыл бұрын
Good Evening, I just wanted to thank you for this video. It was super helpful. You did a great job and all your hints really worked well. Thanks for taking the time to record this. I'm in the process of checking out your other videos. Thanks again!! Michael
@IvanGutierrezDragon
8 жыл бұрын
Thank you very much, I was searching a video with this, now I repair my truck doors.
@milkcrate82
8 жыл бұрын
Thank you for watching!
@richarrrdj
8 жыл бұрын
thank you.......need to get this done on my chevy van (1975) and gmc (1973) pickup. you save me allot of time & guesswork on how to go about doing this job.Again......great job you did.
@milkcrate82
8 жыл бұрын
+richarrrdj Thank you for watching!
@georgegoudima9265
8 жыл бұрын
I removed my door from the hinge and left the hinge on the truck. Then grinded the old hinge pin in half and knocked out the pin top and bottom. Then installed the new hinge pins and bushings. Reinstalled the door and came together fine. If you remove the hinges completely then it will be trial and error to set the hinges against the truck body, if that is necessary, then place marks on the truck body as to where the hinge should match prior to the removal.
@jreed5235
4 жыл бұрын
Thanks
@milkcrate82
11 жыл бұрын
Honestly I don't think you could change the pins in the hinges without removing the hinges from the truck. Maybe you could, but it would be VERY difficult, and you'd likely damage areas around the hinges. The door really needs to come off. Mark the hinges against the doors and cab before you remove them. That will make re-aligning the doors easier when you re-install them. The fender can stay on but you'll likely need a u-joint attachment on your ratchet to remove the hinge-to-cab bolts.
@petermontanez2339
Жыл бұрын
Thank you those little things mean a lot
@milkcrate82
11 жыл бұрын
If you can hear or even worse, see the hinge pin giggling inside the two hinge halves, then you need to replace the hinge pins. The door could also be tweaked. My original doors were rusted out so I put on some aftermarket doors, they were not straight at all. I had to cut and re-weld them a little bit.
@heplertroy
11 жыл бұрын
Thank You!!! Excellent- Exactly what I wanted to see, it helped a bunch!
@milkcrate82
11 жыл бұрын
Happy to help!
@toddbob55
Жыл бұрын
I used OEM GM bushings and pins to rebuild mine......i don't like the aftermarket junk Dorman parts. With the Aftermarkets one thing is the splines come down the shaft to far and bite into the bronze bushing causing it to spin inside the housing
@nandoGdog
11 жыл бұрын
Nice! I'm getting tired of lifting up and slamming my door!
@bryanstock7486
4 жыл бұрын
what are the steel bushings for / No one ever says .
@milkcrate82
12 жыл бұрын
I'm glad it helped!
@harleyb-ham266
3 жыл бұрын
Thanks for the information. So what I see is I have to completely dismantle everything from the cab forward just to change a door hinge?!?
@92Inquieto
11 жыл бұрын
I'm having problems aligning the doors. There's always at least one corner of the door that doesn't close flush with the cab or front fender. Do you think I need new hinges? Thanks
@scohenour
8 жыл бұрын
This is very helpful..I am going to try myself without the hubby. Hope I can manage. :)
@milkcrate82
8 жыл бұрын
You'll do fine! Thank you for watching!
@milkcrate82
11 жыл бұрын
No problem amigo!
@richard-cf8ce
Ай бұрын
Cool I just looked at mine and I got new hinges and I saw that reverse bolt and I just got those stupid engineers
@tableta6305
Жыл бұрын
Hi, great video, So the pin is bolted from the factory? Is it impossible to remove the pin in any other way?, thanks,
@DaBossesTable
2 жыл бұрын
I have this issue thank you for the video
@robertruggles6067
8 жыл бұрын
Thanks, OOH TRIALS BIKE :)
@buckster2575
7 жыл бұрын
Wish i had knew this the other day .
@rcmcguyver7561
2 жыл бұрын
My nylon spur gear that the spring presses up against to hold the door open spins on the PIN is there a replacement for that
@gtuttle4
2 жыл бұрын
Do you actually have to remove the dash components to remove the inside bolt?
@Queenswara562
Жыл бұрын
Appreciated
@drewdowncutomz4792
2 жыл бұрын
Wats the part numbers on both parts
@azdarth1971
9 жыл бұрын
Many thanks! I was ready to go directly to the torch lol. Is it hit and miss, readjust and try again for door alignment?
@milkcrate82
9 жыл бұрын
azdarth1971 Thank you for watching!
@mopster1913
3 жыл бұрын
In my vase. Hahaha noice
@XER239
4 жыл бұрын
do you know the screw size specs?
@BdeSimon
9 жыл бұрын
Where do you have to go through to get to that bolt on the inside for the passenger side? I have an 86 sierra but its exactly the same. I just tried to take my hinges off to replace them and didnt notice that one from the inside on the top hinge
@milkcrate82
9 жыл бұрын
Slichman500 There is a corresponding hole in the same place on the passenger side. You will likely need to remove the cable holding up the glovebox or removing the glovebox altogether.
@ralphgarcia6605
9 жыл бұрын
How did you align the door after wards ? I replaced my drivers side top hinge and door didn't align the same
@milkcrate82
9 жыл бұрын
Ralph Garcia You just have to keep the bolts loose on the hinges... both the door side and the cab side. Adjust the door by hand until it's right and then tighten down the bolts. It's good to have a helping hand with this but it's not too difficult to do it by yourself.
@nandoGdog
9 жыл бұрын
***** I take it the fenders have to be off the truck and the doors shut to allow access?
Пікірлер: 45