Seems an easy DIY job. Can’t believe GM engineers have not found a way to make it more complicated yet
@ZayceM
5 жыл бұрын
Others might have said it before, but an alternative way to do this that is useful if you don't have a lift is to put the front of the car on stands, remove both front wheels, disconnect the outer tie rods from the knuckles (to allow the sway bar to rotate freely), and then you can remove the sway bar by removing the end links and bushings and then twisting and pulling the bar out from one side. The new one can be installed by doing this process in reverse, and you shouldn't throw off your alignment or anything.
@Klwjjj
4 ай бұрын
This method does work but it only can come out the passenger side; the brake lines are in the way on the drivers side. I got to do mine next week -
@ryangray65
7 жыл бұрын
Thanks for the video! I used it to help me change out a broken sway bar this afternoon on my 2001 Impala. For anyone else wanting to do this, I was able to do it in my house garage using car stands and jacks.
@mikebarnes3238
6 жыл бұрын
Eric- this video with your commentary was extremely helpful. I did my 07 last weekend in about 1.5 hours. I used a sawsall to cut the links. Thanks again for another great video.
@workinbootsproductions5008
3 ай бұрын
Great video! Mine just broke today. I’ll be lying on the ground, replacing it this weekend!
@CHIBA280CRV
9 жыл бұрын
Man I almost missed todays episode of South Main Auto ! It was a simple fix , but sure helps pay the bills ! Keep them coming ! Thanks again Eric..
@SouthMainAuto
9 жыл бұрын
***** Oh yeah they all count for sure
@williamdjerf6291
5 жыл бұрын
Good video, I can see the your personality relaxes the installer, especially when you say, "If I can do it, you can do it!". completed the job with this video. What was GM/Chevy thinking, hollow sway bars??? This should have been a safety recall. Anyway, thank-you!
@mikechiodetti6737
5 жыл бұрын
I am really impressed at that aluminum subframe cradle for the powertrain/suspension! That really looks great! Good job, Great Video!
@mjjones8757
7 жыл бұрын
comments from mj this video was extremly helpful. the young man explained the installation very well thanks
@Big_AlMC
3 жыл бұрын
Comments from who?
@gregp05
9 жыл бұрын
Had a long day at the toyota shop i work at, but still watch ur videos haha. Keep up the great videos.
@SouthMainAuto
9 жыл бұрын
***** I know that feeling. We can't get enough haha
@TheSavageGarage
9 жыл бұрын
I enjoy running gear/suspension repair videos, good job!
@supercoupe6288
9 жыл бұрын
I've welded a few of those sway bars, haven't had a come back yet, knock on wood, but as easy as you showed it, think I'll start doing the sway bar replacement.
@SouthMainAuto
9 жыл бұрын
super coupe Yeah they are a piece of cake really
@JordashGenes
Жыл бұрын
You videos give a great outward in ward perspective. Some if these guys just shoot from right up on the piece. And it's hard to get the full picture at first when witnessing this. Great work. 👌
@corkyc6015
9 жыл бұрын
Excellent video. Simple job, but you narrate and perform the task so methodically it's great to watch. Same prob on my sons Intrigue - cracked on top by the link. I just left it alone and monitor it each time he comes into town for food and laundry!
@SouthMainAuto
9 жыл бұрын
Corky C Haha... wait you have free food and laundry service there... what is that address?
@heyitschinoable
8 жыл бұрын
+South Main Auto Repair Lmao
@gregorland1697
4 жыл бұрын
I have a 2002 Impala LS. I am replacing the drivers CV axle. I also am replacing both lower control arms as they are severely rusted. I noticed the drivers side sway bar end had the separation. I thought it was made that way and was going to reinstall it. When I opened the sway bar link kit I got from Advanced Auto it did not have the plastic spacer. I tried to get the old plastic spacer off the old sway bar link but it was rusted on it and broke trying to rescue it. So now I am going to replace the complete sway bar as it should come with the plastic sway bar spacers like yours had. Great video thanks. I am also replacing the upper strut bearings. Scotty Kilmer says the $100 replacement McPherson struts change the ride and ride height of the car because the coil spring is thicker. Mine are rusty but not leaking.
@JeffHazardous
9 жыл бұрын
Did this a few months ago on my dads 2004 Pontiac Montana. I think this may even be the same part number, we didn't have to drop the sub frame, we were able to easily unbolt and slide it out with the tire off. Good video, kind of cool to see something I have done, always thought about making videos of the repairs I do, just don't have the mind set for it, I would just prefer to get the job done lol.
@SouthMainAuto
9 жыл бұрын
Jeff Dooley Bust out a camera, it is fun really :)
@drivewaygarage1561
Жыл бұрын
Thanks for the video, I just bought a 2004 Chevy impala and my buddy and he hit a curb and bent the rim and snapped the sway bar so now I'm going to replace it and this is helpful
@matthewmolitor4287
5 жыл бұрын
Great video just did this fix and its is just as easy as he made it look. I dont have a lift so it did take a little longer than the 15min video, it is just this easy. Thanks for the video.
@jdhitc
4 жыл бұрын
So how did you do it with out a torch
@jshhager07
7 жыл бұрын
I usually do them with the wheels off and use an air ratchet then take it out pass side. seems easy to me but your way is pretty simple as well. great videos!
@mrbreezeet1
2 жыл бұрын
@ Josh Hager Do you usually drop the sub frame too?
@jshhager07
2 жыл бұрын
@@mrbreezeet1 yes sir just the back two bolts
@barrypizzdoff5579
8 жыл бұрын
I wish I had a mechanic like you around me.
@nicknicu1787
9 жыл бұрын
Great video Dr O! Thank you. Impala is my dream car since I was a kid! Lol! Have a great weekend!
@michaels9657
7 жыл бұрын
Nick Nicu 1500 dollor dream.
@matthewrizer6542
4 жыл бұрын
Thank you so much for the video buddy. My wife's sway bar links looked like someone cut them with a hacksaw. Your video helped me tremendously !
@Rickm2003
8 жыл бұрын
Want to say thank you! Watched this video before i did one. This was a video guide. Thanks!!
@DarthTaiter79
8 жыл бұрын
Just had a sway bar link go out on my 2001 Impala. Checking out videos to see just what it is. Thanks!
@whoami7566
3 жыл бұрын
Just changed mine last night and was able to get it out the passenger side by popping off the tirod end. No lowering subframe so I got lucky I guess. Thanks for the video man as it helped me thru my process
@ukraineupdates9380
3 жыл бұрын
I guess if you were able to get it out the new one was easy enough to put back in the same way? just welded the one on my gf 2001 impala, they are hollow but it's pretty thick steel so it welded okay. Going to order one from rock auto and do it when I do the tie rods and I was thinking I could probably get it in there without dropping the subframe. Taking it out would be no problem just cut the bent arms off but if I have to lower it to get it back in then that's pointless.
@marklalonde5329
3 жыл бұрын
Exactly what I needed to see and know! Great job!! I like the explanations and tips and tricks for the driveway mechanics such as myself.
@waynechristner9225
3 жыл бұрын
2004 Impala's were good cars. My wife's 3.8 LS has over 410,000 miles and goes 500 miles or more every week. My 3.4 base has 286,000 and going strong.
@ccgrider1014
7 жыл бұрын
Hollow GM sway bar for lighter weight and better fuel economy!!! I hope my new doerman doesn't hurt my gas mileage! Thanks for the vid
@shaun27ful
9 жыл бұрын
Great video as usual. I learnt one thing from it. You call them sway bars over here we call them anti roll bars.
@SouthMainAuto
9 жыл бұрын
shaun pi Yep they stop the rollin and the swayin :)
@johnbraeking607
2 жыл бұрын
I always called them anti-sway bars since they don’t induce more roll. ;)
@brianlucas1466
2 жыл бұрын
thanks for another great video that same problem just happened to my 2008impala and seeing how easy it is now it going be a DIY project.
@morsecodereviews1553
6 жыл бұрын
"Pretty Simple Job" lol yea when you have a lift, a support, compact electric impact gun, and years of experience. What about this guy doing it in the gravel, mud and blood 2 jack stands, a floor jack and a smattering of tools =)
@BANANAHAMMER420
4 жыл бұрын
@@briancavanaugh4406 absolutely same here....past few years I've been doing my own work on my Impala and my girls Camry. I've had to buy a bunch of tools and what not but in the long run still saving money and learning....I'm not rebuilding engines or transmissions or tunning but done this,replaced front lower control arms,brakes,rear upper and lower trailing arms and controls arms, radiator,water pump....can be a bit frustrating sometimes but satisfying when you diy😎👍
@ryanchenier-poulin8570
4 жыл бұрын
Easy peasey
@evildeaddrew
4 жыл бұрын
How long did it take from the ground?
@morsecodereviews1553
3 жыл бұрын
I never got around to it, my poor Imapala blew her head gasket 😑 RIP 2002-2018
@ukraineupdates9380
3 жыл бұрын
@@morsecodereviews1553 the 8th gen impalas are known to have bad head gaskets in the 2000-2004 years, they break down over time and all will go eventually. The 2005 impala is the best year of 8th gen they changed the head gasket to one that lasts for that year. So if you are looking to get another one of that gen either get a 2005 or plan on doing the head gasket at some point. I have an 2001 that my girlfriends grandpa bought new and it's going strong at 183000 miles, we both love it they are good cars.
@brianlucas1466
2 жыл бұрын
like that straight to the job and get it done but another is why parts like and ball joints, tire rod etc. that don't have any grease fittings on them so u don't know how much grease in there but you'll c when they brake and thank you for the video
@johnzzy552
9 жыл бұрын
I feel lucky living in Texas since we rarely use salt on our roads. Loved the video
@SouthMainAuto
9 жыл бұрын
johnzzy552 I wouldn't know what to do
@DENicholsAutoBravado
9 жыл бұрын
South Main Auto Repair Trust me. Plenty brakes in less rusty areas. :)
@donking1554
4 жыл бұрын
I pulled the sway bar out from the passenger side after dropping the control arm. I found a video on this and since I am a true DIY I would suggest trying it.
@wesleybrabant3595
5 жыл бұрын
Great video..I just changed out my sway bar and links which I purchased it off Amazon . I also lowered my cradle. Like you said easy job.
@ZJIGGA
7 жыл бұрын
Excellent video! Thanks for posting! The underside of my 07 impala looks just like that since I live in MI.
@Bespn008
2 жыл бұрын
Best video ever getting mine done in the morning
@chuckroast5735
5 ай бұрын
If you dont have a lift. Put the front end up on jack stands, remove both front wheels, remove all hardware, (links and rubber hold down brackets). Turn front wheels to the far left. Jack up driver side wheel with jack under the brake roter. Slide the bar out between the driver side tie rod end and lower control arm. Cutting the passenger side bend off the old bar makes it a breeze. Slide in the new bar in the same way. The new after-market bar had been reconfigured and slides in very easily. Replace hardware and wheels.
@ahill007ny
9 жыл бұрын
Excellent video!!! Nice drill!!! Seeing you and Fordtech using those Milwaukee Tools, is making me want them more and more each day!
@SouthMainAuto
9 жыл бұрын
Stanley Hill I can vouch for them
@1982JOEC
9 жыл бұрын
Love all your videos!!...Im a new subscriber and an auto tech. as well. I replaced a few sway bars on the Impalas and I do it the same way you do I think that has to be the easiest way!
@SouthMainAuto
9 жыл бұрын
Joe Caraluzzo Thanks and welcome aboard :)
@JohnRodriguesPhotographer
5 жыл бұрын
You made that look easy. I didn't know you could pivot the subframe like that to do something. That's really cool.
@matthewmolitor4287
5 жыл бұрын
I just did this fix and it's as easy as it looks. Used a jack and two jack stands.
@michaelstair8658
Жыл бұрын
Wow, It's great to have the tools.
@snw56
9 жыл бұрын
Don't see a lot of this problem in the South. Bushings tend to wear out before the sway bar gives way.
@normansmith7806
9 жыл бұрын
Great video. Seen a few of the Impala with sway bar problems on the Police packages. ( No rust) See you have gone Milwaukee, great impacts !
@SouthMainAuto
9 жыл бұрын
***** My friend loaned me those to try... must say... prettttyyyy nice :)
@LAnonHubbard
5 жыл бұрын
Learning lots from your videos. Thanks Eric.
@Loribethdi
3 жыл бұрын
Thanks once again! Just waiting for my parts so I can get started!
@ladavidlee564
7 жыл бұрын
i was changing my breaks on a 2001 buick regal and on my passenger side i saw that the sway bar was completely disconnected from the link. Can i use the same method on my car? My first time working on cars and your videos are very informative. thanks for the help.
@joshuakearney426
7 жыл бұрын
Actually, you can just take off the tie rod if you don't wanna lower the subframe, and pull if out from the passenger side.
@helivesonforever
9 жыл бұрын
3:55 I was thinking you would grunt really loud Scotty Kilmer style!
@SouthMainAuto
9 жыл бұрын
***Classified*** Next time
@hotwheel6663
5 жыл бұрын
Rev up Your Engines!
@dave_yeg3898
5 жыл бұрын
I always hope I can learn new cuss words for when I'm working on cars.
@Brian-iz9sh
5 жыл бұрын
Chevy Chystler is owned by Fiat. Three wrongs don’t make a right. Those things are endless moneypits. Cheap plastic engines...
@silkytp789
8 жыл бұрын
Thanks for this video.. Sway bar on the 02 impala just broke.
@SouthMainAuto
8 жыл бұрын
+Silky Tp Good timing
@wildweenrzdtcom
3 жыл бұрын
Great video man. If only I had a lift lol
@tboy160
4 жыл бұрын
I saw another video where they detached something with the steering, they said they needed to before lowering the subframe?
@rickuyeda4818
7 жыл бұрын
Wow! My original '65 Chevy Biscayne still had the original sway bar. However, I bought a kit from Hotckis and replaced the front sway with a bigger one. For the rear, I added their boxed trailing arms, upper and lower and added a sway bar. What a difference in handling. I think your salted roads do a number on your chassis's.
@biznizbrothersinc420
4 жыл бұрын
Absolutely great work! Thank u for this video!
@547Rick
9 жыл бұрын
Nice video! Thanks for sharing! Is that a new battery operated impact wrench?
@SouthMainAuto
9 жыл бұрын
Rick Anderson Sure is
@SteveRobReviews
9 жыл бұрын
You make it look so easy Eric but on the ground that job is way more than 15 min :) When I worked at the parts store we rarely sold sway bars on impalas and most were cabs. I wonder if your area has a lot of rough dirt roads or lots of pot holes. I do think a lot of your repairs are geographical in nature which is a good thing for you. I wonder if garages in Arizona are as busy as you are except for AC repairs. I have two friends up here working at Ford and Gm dealerships and their both very slow and my closest independent is slowly going out of business because of the lack of work. Over all compared to 30 years ago the cars today are built far better , require less maintenance and last so much longer. Even a Dodge Ha. 👍
@satamanschmidt3428
9 жыл бұрын
Steve Rob All true Steve except here in Arizona cars last forever as they don't rust so there is far more replacement of engines and transmissions than there is in the Northeast since there the bodies are gone long before the drivetrain is. Out here the bodies of the cars last long enough that just about everything subject to normal wear and tear that needs to be replaced already has been before the car needs to be scrapped. Good shops are always busy and bad shops aren't. Eric O. would be busy in the middle of the desert. Others less skilled not so much.
@SteveRobReviews
9 жыл бұрын
SATAMAN Schmidt Good morning Denis. If Eric came up to Canada and kept his rates the same he'd have a hard time and thats the problem at least up here, the imput cost for a garage up here is so much more than in America. Average hourly charge where i am is $85-95 for a independent and $120-130 for a OEM plus a 13% sales tax on top. The problem up here is so many underground garages that are a result of the high cost of going to a legit garage. I guess this is all over but to be a successful indepentant garage owner like Eric is not the norm as i see more and more close down. SMA is a gem for sure.
@BigMac2222
9 жыл бұрын
Steve Rob That's actually cheaper than where I live in the States. Seems to me Eric has the right abilities to narrow his customers' problem down to a single root cause, unlike some that throw the whole book at the car and cross their fingers when they fire it up. My customers think I'm a magician with a test light, they're happy enough to pay me that I almost feel bad.
@SteveRobReviews
9 жыл бұрын
Derrick Hodges Thats interesting . As you well know a lot of shops are parts changers and not even good at that:) but reality is that's how a lot of shops make a living. I always heard the saying an honest mechanic was a broke mechanic , not always true but we've all had experiences either way. Running a garage is so much more than doing repairs . Ha and making KZitem vids on top , just incredible.
@BigMac2222
9 жыл бұрын
Yeah, lots of guys out there think they are fixing cars. Unfortunately thinking and knowing aren't the same thing. : )
@jim52970
6 жыл бұрын
Great "to the point" how to video!
@zackconklin6521
3 жыл бұрын
Simple job I did my rack and pinion in the garage with a floor and jack stands... Just need a little come sense and you can save hundreds if not thousands in labor...
@steve0l
Жыл бұрын
Yeah, same here. On my 07 Chevy Impala, it was not a fun job. Oh and did I also forget to mention I have replaced every single suspension part, Breaking part, such as all calipers rotors and pads, all wheel bearings, all 4 struts, ( fronts twice) thats what i get for replacing them with crappy cheap Detroit Axle junk, just 3 months later the started leaking,inner and outer tie rod, lower control arms with ball joint, spark plugs, map sensor, mass air flow sensor, ignition coil pack, fuel injectors, air intake plenum, the flex pipe from the manifold to the cat, cabin filter, air filter, power steering pump, both power steering line, both transmission lines, a full transmission fluid drain and replacement with Filter, the oil filter gasket housing thing I can't remember exactly what it's called, sway bar end links twice. That's what I get for buying really cheap sway bar end links. Both CV axles, the steering wheel clock spring. Honestly I think a few more part I just can't think of all off the top of my head. I just hit 190,000 miles on that car and I still do have a few minor repairs, such as the three separate actuated mowers for the air conditioner, air adjustment thing, from switching it to window defrost to front vents. Surprisingly that motor is still very solid. Although it does leak a little bit of oil with Adele cover gaskets which I still have to replace.
@brucesinclair7801
6 жыл бұрын
Thanks very much! Excellent video!
@Rhuffman93185
6 жыл бұрын
thanks for the vid, saved myself $300 (or more) dollars doing it myself
@chiefx111
9 жыл бұрын
South Main Auto Repair seems like your always using a impact tool. I bet it makes life so much easier removing things like bolts and stuff. Why do you use different ones thought out repairs instead of just one? Always wondered that.
@SouthMainAuto
9 жыл бұрын
well... not really sure. I guess i just use what ever is the handiest .
@ChevyBuddy
9 жыл бұрын
Hey there! Great Video as usual. Let me ask you a question though - What do you think of those 9th Gen Impalas. Do they come in a lot? If so what kinda work is the most common that you need to do on these. Thanks and keep up the great job.
@SouthMainAuto
9 жыл бұрын
***** I work on so much stuff I don't go buy 1st 2nd 10th gen or any of that fancy stuff. Give me a year range and engine type and I can tell ya what I see come and go...
@ChevyBuddy
9 жыл бұрын
South Main Auto Repair Sure. I was speaking of the 2006-2009 Impalas with the 3.9 V6 or even the SS with the 5.3 V8. Thanks in advance for your answer!
@SouthMainAuto
9 жыл бұрын
You know I tell ya , ya see them come in for the wheel bearings, brakes, tie rods, blower resistors, sway bar links, etc. (typical GM stuff IMO) I feel the engines are pretty solid really. I do a fail amount of A.I.R. diverter valves but that is about all I can think of in the moment.
@Gideon_Judges6
7 жыл бұрын
wow that's crazy. always though sway bars were solid steel. When I read the title I figured maybe only the end link broke because GM used to use cheap plastic end links on some cars
@SouthMainAuto
7 жыл бұрын
a lot of them are hollow
@nicholasmenasian1142
6 жыл бұрын
Yes I had a 2009 aveo and a hhr and a 2015 Malibu now a 2017 Malibu and they where all hollow car's you felt every bump on the road and felt loose yes even the 2017 Malibu but now a can't afford another one for a while it won't be a GM car or any of their products
@blainemcdonald6972
Жыл бұрын
Most if not all of us back yard mechanics work on our backs with the vehicle on stands😊
@BIG_GAME_WAYNE
5 жыл бұрын
Thanks for the video homie. My first sway bar swap. 🎆🎇🎆
@chevyracer5091
2 жыл бұрын
ZZP performers Has great Price its where i got mine at. They have a bar that is solid on the ends. No i don't work there Just got great deals everyone should no about!
@ChiTownGuerrilla
5 жыл бұрын
What did you charge for this job? Cause my brothers sway bar is bent on the same car. Please answer
@Tem782
9 жыл бұрын
Gotta love rust :D I have used copper grease on those a lot and it works..
@donaldrickett2450
Жыл бұрын
How long dose it take to do each one when everything you just used bc I have all that. And you made it look so easy.
@nmattcar
9 жыл бұрын
I'm starting to feel like front sway bars are a common problem on gms.from the older grand prix to the express van my experience is they all break in the same place.
@SouthMainAuto
9 жыл бұрын
nmattcar yep they all break the ears off them
@michaelspeakman8924
5 жыл бұрын
The Buick century's have the same problem and they put a solid or across there. Anti-sway bar. Is a failure being hollow. Stuck a solid one backup in mind from GM.
@dannyhenson6532
9 жыл бұрын
thank u for that log it was a good one cant wait for the next one
@RetroPCUser
2 жыл бұрын
Waiting for FedEx to deliver my front assembly since mine is out of commission along with the front controller arms, rear strut assemblies, rear bushings, and links for my 2001 Intrigue. I have most of the parts to do my suspension, yet the front sway bar assembly isn't here yet.
@mrbreezeet1
2 жыл бұрын
I wasn't sure, so you say that you don't have to worry about loosening the steering shaft from the rack when you drop the sub frame? Is that a slip joint of some sort at the steering shaft?
@DJDevon3
9 жыл бұрын
Never heard of the bushing bracket being referred to as saddles. I like that term it makes a lot of sense but now I see a little horse under them in my mind. That's cute.
@SouthMainAuto
9 жыл бұрын
***** If the camera was off I'd actually make little horse sounds and prance around the shop with one haha.
@RealCadde
9 жыл бұрын
South Main Auto Repair But then your boss would tell you to stop horsing around?
@SouthMainAuto
9 жыл бұрын
Cadde I wouldn't listen
@user-gw1pu4io8x
Жыл бұрын
Can you make a video on how to replace the bushings on a sway bar for a G6? I know how to the swaybar link it the sway bar ones that seem to be a pain. If you do, thank you in advance
@am529
7 жыл бұрын
I live in central Indiana. Always have to cut old sway bar links to remove them. Don't have a torch yet.
@steniofernandez824
9 жыл бұрын
Hey eric!!you a very knowledge and smart person ..just a question do you know or any body know if inspection license could be transfer to other states???
@SouthMainAuto
9 жыл бұрын
Stenio Fernandez Nope different in every state
@Ausblack
9 жыл бұрын
Welcome back to the fluid foam!
@RealCadde
9 жыл бұрын
You've swayed me Eric.
@SouthMainAuto
9 жыл бұрын
Cadde Haha good
@danielrehm5008
5 жыл бұрын
Who ever said you had to support the subframe? I slid my sway bar out from the side, and popped her right back in. I've been trying to figure out why people keep saying you have to support OR disassemble the subframe.
@blainemcdonald6972
Жыл бұрын
Good idea to use safety glasses 😮
@poo4me1
2 жыл бұрын
you dont have to disconnect steering shaft before lowering sub frame?
@AlLuchik-du6nb
5 ай бұрын
How far can you drop the subframe before you have an issue with the steering link
@tsistrun
9 ай бұрын
Do you happen to know how many subframe bushings total are on a 2006 chevrolet impala ls?
@langent4653
2 жыл бұрын
Don't you have to loosen the pinch bolt on the steering column to rack connection so it doesn't stress the steering column? A shop just replaced mine and now the steering is very stiff. They think its the steering column. Its got 31k original miles so I think they screwed something up... Any ideas? Thanks.....
@chosipian
Жыл бұрын
wonderful informative videos
@arcdraw
9 жыл бұрын
You make it look easy, Eric. BTW I saw that you got a new red toy :)
@SouthMainAuto
9 жыл бұрын
arcdraw Haha good eye :)
@innojay7
8 жыл бұрын
What size are the bolts on the subframe would the size be the same for a 07 impala LTZ?
@d.4tay549
5 жыл бұрын
2002 Impala LS. Mine broke at around 70,000 miles. Great car when everything works. And then breaks and then works and then breaks and then more $$$$. Nice car when everything works, oops another idiot light is on. $$$$$.
@sethlee8055
6 жыл бұрын
Did you have to relieve the pinch bolt before lowering sub frame?
@TJHawk88
5 жыл бұрын
I was thinking the same thing. The steering rack is mounted to the subframe. Any time you lower the subframe you really should disconnect the pinch bolt from the steering rack input shaft.
@tysonclark8668
2 жыл бұрын
Thanks brother. That helps me a lot.
@pskinny36
Жыл бұрын
2015 Chevy impala 3.6 v6. I need sway bar install, took old one off. The shop said its $1000 labor to install. Does that sound right?
@mrbreezeet1
2 жыл бұрын
01 Grand Prix...... I hit my wheel, bent control arm and inner tie rod end. Got the inner tie rod end on, and lower control arm on. I'm trying to install the sway bar link, and the sway bar is too close to the lower control arm to get my sway bar link bushings in place. I started to loosen the two bolts holding the sway bar itself to the sub frame but the front one (of course, the hardest one to get at) Is fighting me the whole way out. I wasn't going to replace the sway bar link on the other side at this time. But do you think I need to cut the sway bar link off of the other side so the sway bar will swing up enough to install the 1st. side?
@domowalker1679
5 жыл бұрын
Curious to know if the same setup if for an 2008 Malibu. I’m pretty confident I could change one out.
@bfnfedboy2
8 жыл бұрын
without just seeing that the sway bar is broken would it give any symptoms?
@fitzmeister5992
3 жыл бұрын
As usual, a well done video.
@mikes4408
9 жыл бұрын
"Just buzz them off" Not in my world. Last time I did my sway bar bushings had to bring it into my mechanic to drill out the broken bolts. All most replaced the carriage. Nice job though!
@SouthMainAuto
9 жыл бұрын
Mike Shelly Oh man bummer
@dcrickerson9775
9 жыл бұрын
Nice find and fix. Nice video.
@SouthMainAuto
9 жыл бұрын
DC Rickerson Thanks
@emitt1
9 жыл бұрын
Fine job, my friend.
@SouthMainAuto
9 жыл бұрын
Stephen Malone Thanks Steve
@xelism86
8 жыл бұрын
started the project at home and having a had time with one of the crane screws other one came out with some pressure but cannot get the other one off ..any ideas for a guy with no power or air tools...
Пікірлер: 417