Had my truck 13 years , am a professional mechanic and never figured out how to do this lmao . Thanks !
@lancezubritsky7668
Жыл бұрын
Your obviously not a professional mechanic if you don't know how to remove a steering wheel
@lostkauz83
Жыл бұрын
@@lancezubritsky7668 I think 25 plus certifies me, Deisel, bendix air brake certs and numerous certs through Linde. Unlike you kids, I grew up without airbags so I really didn't feel like getting hit by it if I made a mistake. SMDH everyone on the internet thinks they're genius's LMFAO
@RWBYGaming
2 жыл бұрын
I have a jiggly wheel too lmao i thought it was just normal on these s10s and nomas but thank you for uploading this. One of the most straightforward yet in depth tutorial ive seen yet on these quick releases. Cant wait to get mine
@joecameron3406
3 жыл бұрын
I always learn something when I watch I have my column apart had to tighten my column getting to the 4 bolts is time consuming but fixed it
@madmike_9343
3 жыл бұрын
Thanks!
@bradpilkington6098
3 жыл бұрын
Awesome video man, showed me i missed a ton of steps on my old truck. Going to get the same adapter you did for my 2000 and referance this video for the install!
@madmike_9343
3 жыл бұрын
Thanks, just a note since I have a loose gearbox it was hard to determine when the steering wheel was straight but after driving it for a while I noticed it was cocked to the right a little bit so what ended up doing was cutting the white plastic tube thing flush with the aluminum adapter so I could run the wire through the groove and it looks like that put me straight
@dancullen499
2 жыл бұрын
Looks good something that's on my list to do to my 01 S-10..... I also want to add a tilt column to mine..... Forever sharp looks like a well made product....
@gering46
3 жыл бұрын
Before you replace your gearbox I have a suggestion for you, Look into eliminating your rag joint. You can do it by getting a intermediate shaft out of a 88 to 94 jeep Cherokee
@madmike_9343
3 жыл бұрын
I did do that actually, I have a bad gear box
@jonathanhudson4623
2 жыл бұрын
Not only can you do the jeep Cherokee shaft you I'm 99% sure you can get a lot tighter steering box from a late 80 (mine is an 89) WS6 optioned formula firebird, GTA, or Camaro z28 or iroc-z) my steering box is still I my 89 formula firebird because I built a fully race built stroker 383 and converted from the automatic 700r4 to a manual 6 speed from an LT1 powered Camaro SS, but alot of guys get the fast ratio steering boxes from late model 3rd gen f-bodies (camaro and firebirds) to put in other cars. all WS6 optioned firebirds before 1992 should be the right one. I'm a firebird guy but about 98% of everything crosses over between the Camaros. I think they are 3 turns lock to lock but might actually be a little tighter than that (I cant remember off the top of my head) I built the 89 formula when I was 16 which was 21 years ago and if still runs 10s in the 1/4 and I can still daily drive it. I also have a 2000 zr2 4x4 s10 and I learned about the Cherokee shaft because its narrower and gives just enough clearance to use 98 or 99 cast steel ls1 f-body exhaust manifolds to do a LS v8 swap into a 4x4 S10. You need the 98-99 ones because thet are cast steel and you can werks them easy since you have to cut the flabge off and add an extension to the deived side at the very least. the newer 2000-2002 ones are cast iron (or I'd use the ones off my 71k mile 2002 WS6 TransAm 6speed). The 02 also runs 10s and is my daily driver. Both cars have nitrous like most everything else I've modded. The zr2 s10 is my first LS swap and first turbo build and despite the nah sayers it will have A/C, power everything and be as normal of a daily drived as my 02 transam is, until you stomp it. actually more so if an easy daily since it will be an automatic. If you ever want to do an LS swap look for an L33 5.3L (5300 H.O.) because it's an aluminum block 5.3L with 799 heads which are the same casting as the 243 heads on an ls6 and it weights the same or maybe a bit less than the all iron 4.3L (big deal for 4x4 guys with torsion bar front suspensions). Theres alot of tricks to free up the power on the 4.3L but the intake is the killer. You can actually get good cams, heads, headers, and full exhaust but that spider injection intake is junk. Also the 4.3 likes to break the block with most any power adder. If you haven't replaced the steering box yet make sure they are the same and get a new/remanufactured one for a 1989 WS6 (performance package) formula firebird it will really tighten up your steering. Alot of 3rd gen f-body stuff swaps over to the s10. I've noticed a ton of guys have transams or camaros along with their s10. Probably because of the drivetrain similarities.
@photondebuger45
3 ай бұрын
@@madmike_9343Have you adjusted it at all possibly?
@madmike_9343
3 ай бұрын
@@photondebuger45 I haven’t messed with the steering tbh
@photondebuger45
3 ай бұрын
@@madmike_9343 i mean that's something that is like free ish to do besides time. If you feel it's bad then a small adjustment wouldn't harm it really.
@BattleOfBowties
3 жыл бұрын
Hulk yank! Lol good job subbed.
@854XTOY
2 жыл бұрын
Ah I see you've had trouble with VATS too. Man I had a hell of a time figuring that shit out why my sonoma wouldn't run.
@Bumpinghum
Жыл бұрын
Just ordered the same wheel for my 97 s10 but with the chrome instead of black metal 🤟
@19lucio79
3 жыл бұрын
Came out nice bro thanks for the video 👍👍
@randallsabado6852
Жыл бұрын
Thanks for the tutorial 👍🏻
@soyelua8477
3 жыл бұрын
Nice Job
@HiDezert66
2 жыл бұрын
Thank you for this video, it help me out a lot!
@brandonmunday1494
17 күн бұрын
Dash looks good How did you get your dash painted and it actually look glossy and smooth? Any interior panels I've tried any color change on always scratches off so easily leaving the original color showing and always dull / flat looking. Ended up looking like cheap spray painted interior. just got a s10 extreme for a project and want to do my dash and interior panels but don't want to trash my interior 😂
@madmike_9343
17 күн бұрын
@@brandonmunday1494 it’s kinda a process but I can walk you through it. First, you gotta clean with alcohol and sand it with 180. Next get some filler primer give it like 3 coats . Take some flat black spray paint and mist your panel. Wetsand with 320. What you’re looking to do is get rid of all the flat black spray paint it will show you low spots. Once that’s done, you can use your spray paint use color and clear . I would avoid the single stage paints if you can.
@bendino9016
2 жыл бұрын
s10 gearbox is alway like that after some miles and years.
@tuttlesr
2 жыл бұрын
Ok got another question,,,do you put the original nut that was holding the steering wheel on, back on? Or does those three screws supposed to hold it on. I didn't see you put that big brass nut back on. Excellent work!!!
@madmike_9343
2 жыл бұрын
Yes original nut goes back
@blazebrady3659
4 ай бұрын
Since you've obviously had some time with this wheel, can you ( or anyone else with experience in this) tell me how got it gets in peak summer months, how overall comfortable it is, and how well its holding up?? Any negatives tgat you have learned over time???
@madmike_9343
4 ай бұрын
It does get a little hot in the summer (Texas heat) but the leather foam makes it bearable till the a/c cools it down. Aside from that no complaints
@jordanwurz1024
3 жыл бұрын
Looks awesome
@meademorgan6614
Жыл бұрын
Did your airbag light in your instrument cluster light up and stay on, after your install?
@beatsbykido
8 ай бұрын
wondering the same thing
@NBAwasBetterInThesands
2 жыл бұрын
Bro, I have an 01 Tahoe. Putting a Forever Sharp wheel on. Have the same adapter, and same problem with the clock spring with the plastic clip piece in the way. When you remover the clock spring and clipped that remaining wire that was plugged into it, did you have a airbag light staying on?
@madmike_9343
2 жыл бұрын
Honestly I can’t remember if it was already on, I’m just removing the bulbs next time I get back there, who needs air bags anyway
@AdrianGomez-su1uz
3 жыл бұрын
Thanks for the video I’ve been wanting to do this on my s10 for years
@madmike_9343
3 жыл бұрын
Do it bro!
@shadetree10000
3 жыл бұрын
😎
@Kevin_Yagoonie
Жыл бұрын
Helpful video. But I have a question. Why wiring the horn button did you splice the 2 wires into 1? Don't the back of the horn button have 2 connections?
@madmike_9343
Жыл бұрын
No I used both connections
@barbiesawada5916
3 жыл бұрын
You can get a beautiful steering wheel from Grant and retain the Airbag which is a law to remove it.
@madmike_9343
3 жыл бұрын
I’m above the law
@miguelzavala4523
Жыл бұрын
makes me laugh when people remove an airbag for a skull crusher on a street car
@Martinez-gs7rc
3 жыл бұрын
Killer!
@s10life
3 жыл бұрын
totally dig that new wheel
@pairsnpaint
5 ай бұрын
Can you put the clamshell back on once you have the hub adapter on (before screwing the wheel to the hub?)
@madmike_9343
5 ай бұрын
Yeah I suppose you could, would probably be easier to do so
@Fox666ification
2 жыл бұрын
thanks for the video bro , i installed that same steering wheel today and i was wondering if you deleted the air bag light and how?
@madmike_9343
2 жыл бұрын
Pulled the bulb 😉
@meademorgan6614
Жыл бұрын
@@madmike_9343 easiest fix of all. 😂😂
@BarrioBuildz
3 жыл бұрын
Bro who did your dash to fit the iPad . That’s sick 💯
@madmike_9343
3 жыл бұрын
I did! I have a video on the channel check it out
@BarrioBuildz
3 жыл бұрын
@@madmike_9343 send me your email. I want one for a 95 s10
@madmike_9343
3 жыл бұрын
@@BarrioBuildz Michaelh1017@hotmail.com
@codycastro8083
7 ай бұрын
I wanted to add a slime quick release for my steering wheel I have a 94 S10. Do you have a recommendation?
@madmike_9343
7 ай бұрын
Quick releases are tricky you just don’t want it to pop off while driving lol 😝 I’d just shop around and look at reviews
@RevRumble_
3 жыл бұрын
Nice dude. How much? Did it come with everything?
@madmike_9343
3 жыл бұрын
190 with tax, and yes everything I needed, link in the description.
@santiagocontreras7968
2 жыл бұрын
I have a 2000 Sonoma I bought with the steering wheel already changed out. Question is, are you having any issue with the gear lever being to close to the steering wheel.
@madmike_9343
2 жыл бұрын
No issues so far
@tuttlesr
3 жыл бұрын
Hey got a question when trying to pop off the remove the air bag, is there like a torx screw in the hole do you pry above that screw or take the screw out then pry. Sorry about the question seams weird to me it just will not pop lose...
@madmike_9343
3 жыл бұрын
No they are just metal tabs it’s hard to find the right angle but just use some force, it should come out Look at 5:25
@tuttlesr
2 жыл бұрын
@@madmike_9343 finally got it thanks 😊
@tuttlesr
3 жыл бұрын
Where was your battery box located?? It was had to tell.
@madmike_9343
3 жыл бұрын
I moved it to where the 3rd seat used to be, here is the video on it. kzitem.info/news/bejne/q32j0HZrhnuImG0
@GtPRiCH
Жыл бұрын
I just did mine now my gas hand is dead lol wtf man its pointing to the battery voltage
@madmike_9343
Жыл бұрын
Could be a coincidence, before I did the steering wheel swap I had the same issue , it was float in the gas tank
@GtPRiCH
Жыл бұрын
@@madmike_9343 it was the trip reset button on the dash thank god lol I guess it was thrown off by me unplugging the battery in back in action now! Thanks for the video also I followed each step and got it done ✔
@lilshag347productionsii6
Жыл бұрын
Im planning on swapping the 5 spoke airbag wheel on my 95 for a 94 2 spoke with no airbag. Is it a similar process to this one? Will it work?
@madmike_9343
Жыл бұрын
Yes similar but different adapter I believe
@lilshag347productionsii6
Жыл бұрын
@@madmike_9343 will i have to get the adapter off of the column?
@madmike_9343
Жыл бұрын
@@lilshag347productionsii6 no it’s an aftermarket adapter
@lilshag347productionsii6
Жыл бұрын
the steering wheel im talking about is the factory two spoke wheel
@madmike_9343
Жыл бұрын
@@lilshag347productionsii6 oh I got ya, I’m not sure tbh
@esegarcia908
2 жыл бұрын
Does your airbag light stays on? It does on mine ,but I didn't remove the white plastic or airbag yellow cable
@madmike_9343
2 жыл бұрын
Yeah I think mine was on before I did the swap but I just pulled the bulb. Airbag are for chumps lol jk
@LifeOfSD1
6 ай бұрын
Did your ground wire and screw come with the kit?
@madmike_9343
6 ай бұрын
Yes it does
@DereckVZDeezy
2 жыл бұрын
Bro that dash is 🔥🔥🔥where'd you get it from?
@madmike_9343
2 жыл бұрын
Thanks man I actually made it. There’s a video on my channel.
@DereckVZDeezy
2 жыл бұрын
@@madmike_9343 I'd love to have this in my truck....ima ✔️ out ur video
@tjicer
3 жыл бұрын
Hey looks like the link for the kit is out of stock on ebay would you know which adapter yours came with to order off of forever sharps website when I use their website search tool it just shows a A16 adapter but ebay and other places look like they're multiple chevy adapters.
@myassizitchy
5 ай бұрын
Almost all chevys from way back in the 80s will fit up untill these new 2013 trucks. Full aize and chevy cqrs have same steerin wheel spline so it doesnt really matter. I have an 06 s10 with a 71 Oldsmobile 4 spoke wheel. Really sharp ane rare hard to find but ive done a ton of these so any gm adapter will work even a grant polished adqpter will fit these forever sharp wheels. I used on on my sons 95 s10. Same wheel this dude hqs but a polished grant adapter
@desalvothedon
4 ай бұрын
@myassizitchy I would really like to know where you got an 06 s10
@DavidJohnson-zi5qs
3 жыл бұрын
Did you screw the adapter on or how’d that go? As I seen unless I missed it you just took a mallet to it?
@madmike_9343
3 жыл бұрын
Yea it just press fits on there. If yours is rubbing try taking a socket with a bigger diameter than the bolt and give it a few smacks. If that doesn’t work then trim your plastic
@joshamy39
3 жыл бұрын
So you don't have to put that big steering wheel nut back on?
@madmike_9343
3 жыл бұрын
J&C well yea that way the aluminum adapter don’t come off
@LifeOfSD1
5 ай бұрын
Is the hub supplied from eBay the same as the forever sharp hub?
@madmike_9343
5 ай бұрын
Yes sure is!
@tuttlesr
2 жыл бұрын
What happened when you cut the wires of the clock Ring? Anything I got all mind all together but can't get the ring wire unplugged...thanks again
@madmike_9343
2 жыл бұрын
Nothing happened, just make sure battery is unplugged when you cut it
@tuttlesr
2 жыл бұрын
Did you pull the other end of the clock spring out from under the dash? I don't like bothering people but I just can't get the CS unplugged from under the dash ( does it matter if I leave it in) I cut and wrapped the wires with the battery disconnected.
@madmike_9343
2 жыл бұрын
@@tuttlesr no worries I just cut and taped it, didn’t want to deal with it lol
@tuttlesr
2 жыл бұрын
Thank you so much thats sounds like a plan Scott the guy I got the hub from said to pull it from underneath the dash also. Anyway great videos love watching them especially the wing on the tailgate that's my next project.....
@blairbilliot6658
2 жыл бұрын
Any idea on the part numbers on the 2 small boxes?
@jesusmarin2644
Жыл бұрын
Mine is different it was 2 red wires on the steering wheel and I can’t remove them without railing them off do they matter at all
@madmike_9343
Жыл бұрын
Post a vid so I can see
@nobullshiit5682
2 жыл бұрын
so is the adapter plate only hammered on with no bolt holding it in place ? doesn't seem right without that bolt maybe I missed it
@madmike_9343
2 жыл бұрын
The center bolt holds the adapter plate, never realized I didn’t show it lol
@nobullshiit5682
2 жыл бұрын
@@madmike_9343 yeah cool man nice dash bezel looks factory , Ive been attempting to make a fiberglass mold for the dash bezel so I can pop some carbon fiber bezels out but its been a real pain in the ass and the first attempt failed wax and POV didn't work and it still chemically bonded ,shit I should of stuck with power steering fluid like normal but I had to go and try the "profesional" way or something and it froze together unable to pop apart had to throw in the trash but learned alot from the first one hopefully this isnt a 3 times a charm job lol
@madmike_9343
2 жыл бұрын
@@nobullshiit5682 I did I video of fiberglass awhile back, I used transmission fluid, check it out. One I get a shop up and moved in one of my projects are to make fiberglass dash bezels to sell online but it will be a different method
@lilshag347productionsii6
9 ай бұрын
can you put a clear crimp connector on the bare wire where the clockspring connector was?
@madmike_9343
9 ай бұрын
I suppose so
@craigcarter5276
22 күн бұрын
The back of my steering wheel broke off while removing it and is stuck on.
@madmike_9343
22 күн бұрын
@@craigcarter5276 oh dang! Get a puller and some lube
@craigcarter5276
15 күн бұрын
@@madmike_9343 is there any way to turn off the airbag warning ⚠️ light
@madmike_9343
15 күн бұрын
@@craigcarter5276 yeah pull the bulb
@shortkid_jd2302
3 ай бұрын
What’s the part number on the adapter?
@anthonywhitehead9660
Жыл бұрын
Ok
@gabriel_kutz
Жыл бұрын
Is the air bag still there even tho u did the steering wheel change
@madmike_9343
Жыл бұрын
Only passenger side is. The air bag sits in the steering wheel.
@Johnjohn00001
2 жыл бұрын
You Think this work for my Chevy Colorado 2008 truck 🤔?
@madmike_9343
2 жыл бұрын
You might have to buy a different adapter but should be the same
@frankrivera152
3 жыл бұрын
Will this fit on my 2003 Chevy s10?
@madmike_9343
3 жыл бұрын
Yea don’t see why not mine is a 2002, I will note and I’ll pin the comment , since I have a loose gearbox it was hard to determine when the steering wheel was straight but after driving it for a while I noticed it was cocked to the right a little bit so what ended up doing was cutting the white plastic tube thing flush with the aluminum adapter so I could run the wire through the groove and it looks like that put me straight. Honestly though I love the mod changes the look on the truck
@coreypichler7161
Жыл бұрын
Ok I have the same wheel.please give me the part number on the adapter you used.
@madmike_9343
Жыл бұрын
A01 adapter
@coreypichler7161
Жыл бұрын
@@madmike_9343 it shows only to 94.itll still work?
@madmike_9343
Жыл бұрын
@@coreypichler7161 yea mines an 2002
@chico6085
2 жыл бұрын
Where did you get the dashboard? I'm trying to doing something similar to my truck
@madmike_9343
2 жыл бұрын
I made it, I have a video on my channel check it out
@chico6085
2 жыл бұрын
@@madmike_9343 nice.. Make me one
@madmike_9343
2 жыл бұрын
@@chico6085 I can’t man, I don’t have as much time as I used to.
@loveja1
2 жыл бұрын
How do you know which adapter to buy?
@madmike_9343
2 жыл бұрын
I just looked it up on eBay there’s a link in the description
@bradpilkington6098
3 жыл бұрын
Does your hub scrape on the steering shroud? If not. How?
@madmike_9343
3 жыл бұрын
It does not, it has proper clearance
@lian5798
3 жыл бұрын
Hey man any chance you have ig? Just bought a 2001 s10 and I have a couple questions about the steering wheel.
@madmike_9343
3 жыл бұрын
I don’t but feel free to ask here
@lian5798
3 жыл бұрын
@@madmike_9343 I'm a big guy so I want something with less dish and smaller did you notice any difference on space?
@madmike_9343
3 жыл бұрын
@@lian5798 very small amount it went from a 15in diameter to 14in diameter
@mlcallaway1929
9 ай бұрын
Any air bag lights come on after install??
@madmike_9343
9 ай бұрын
I wouldn’t know, I pulled the bulb
@kevingresham4019
Жыл бұрын
Hey will this steering wheel fit on a 2002 s10?. On ebay its claiming it wont fit
@madmike_9343
Жыл бұрын
Yes mines an 2002 , the reason it says it won’t fit is because of the plastic connector inside is too long but if you cut it in half it will fit
@matthewsmith5651
5 ай бұрын
Did you bypass the anti theft system?
@madmike_9343
5 ай бұрын
Negative
@djayy3966
8 ай бұрын
what’s the name of the adapter?
@muffinman1309
Жыл бұрын
Did the airbag light ever come on?
@madmike_9343
Жыл бұрын
Yes it did but just pull the bulb and all your troubles will fade away
@calebturnbo2481
2 жыл бұрын
How did you do your speaker pods???
@madmike_9343
2 жыл бұрын
kzitem.info/news/bejne/y4qm1KiOnp-WZWk
@tannerhederson4067
3 жыл бұрын
Did this cause a air bag light ?
@madmike_9343
3 жыл бұрын
That’s a good question, not sure since mine was already on for the passenger, I’ll see if I can figure it out and get back to you.
@tannerhederson4067
3 жыл бұрын
@@madmike_9343 please do love ur video I hope u make a ig or fb I'm sure the guys on the s10 pages would love to see ur videos and recomend anything for a cracked dash besil
@madmike_9343
3 жыл бұрын
@@tannerhederson4067 yea for your cracked bezel, roughen the underside plastic where broken with 80grit and clean with alcohol, tape the broken piece back on the front. Buy some plastic epoxy (make sure it sticks to ABS plastic) and glue it on the sanded side, reenforce with fiberglass if needed.
@tannerhederson4067
3 жыл бұрын
@@madmike_9343 thanks I'll give a shot
@tannerhederson4067
3 жыл бұрын
@@madmike_9343 ended finding a new dash besil for a good price but how do u get it flat and beautiful wen u paint it
@blairbilliot6658
2 жыл бұрын
A01? A02?
@madmike_9343
2 жыл бұрын
Man I don’t remember but it might of been A01
@stevedeleon8775
Жыл бұрын
Let's hope his insurance agent isn't watching this FOOL taking his AIR BAG off his steering wheel .. instant termination of his policy...plus if he ever gets in a front collision..the other person's attorney will win the case
@madmike_9343
Жыл бұрын
You seem like the kind of guy to like his own comment… haha dude this is a show truck chill out
Пікірлер: 165