⭐⭐⭐⭐If you liked the video and want to show your support, you can use any of these links to purchase ANY ITEM you normally would off of Amazon and we get a small commission with no extra cost to you! Make sure to complete orders through the links! Thank You! DEWALT 20V Max Impact Driver Kit, 1/4-in: amzn.to/3y0vDRJ 5 Pieces Magnetic Telescoping Pick-up Tool Kit: amzn.to/3knxckI Magnetic Screwdrivers Set with Case, Amartisan 42-piece: amzn.to/39sTSxT CRAFTSMAN Mechanics Tools Kit with 3 Drawer Box, 216-Piece: amzn.to/3Nux6UL ANCEL V6 PRO Bidirectional Scan Tool: amzn.to/3wRcvDy CASOMAN Master Torx Bit Socket and External Torx Socket Set, 60-Piece Set: amzn.to/3NbWUpe Thorstone No Spill Coolant Funnel Kit: amzn.to/3m1dADS
@RideaKawasaki77
2 жыл бұрын
Thank you so much fir the video. I was wondering if tranny can then be removed from same hole in the front. I need to do a tranny swap on an 2013 Traverse AWD. I don't wanna figure out how to get vehicle 4 feet up in the air to remove engine/tranny/sub-frame from bottom. Thanks for any input. God bless.
@scottl546
5 ай бұрын
After watching this video, I feel very confident that pushing my 09 chevytraverse off the nearest cliff is the best route for me! Great video though 👍
@sharpcarco
5 ай бұрын
Well, I totally feel you, Scott.. It’s really not bad taking that out though.
@R2RMINISTRIES
4 жыл бұрын
Nice! I’m doing an 08 Traverse from the top now & I’d rather do it from top than dropping bottom!
@Market_time799
3 жыл бұрын
Great video! It helped me a ton. I’m in the process of reinstalling the “new” engine right now. The hardest part is getting the engine and transmission to mate up. After a couple of frustrating days I loosened up the transfer case and it lined right up. A reinstall video would be an awesome help if you could find the time.
@sharpcarco
3 жыл бұрын
I really do wish I could find a time for reinstall video David and I wish I could also do a nut and bolt video on this but like I said in this video unfortunately these guys don’t get paid by the hour they get paid by the job so me adding a couple of days to their procedure would not help them at all sorry about that
@randallkemp573
20 күн бұрын
Man, this video is just what I needed!!! I got it out pretty quick. The install is going to be super fun especially getting that power steering pump back on and lined up
@mikeb2836
3 жыл бұрын
Just a heads up for anyone curious. If you do not have a refrigerant collection system you do not need to remove the ac condenser or pump. You can leave them both connected to the vehicle even with the rear ac system. It is easier to remove them but not necessary. Also Ive seen it asked more than once, With an awd you have to take the transfer case bolts out.
@sharpcarco
3 жыл бұрын
The bolts don’t necessarily have to come out they just need to be loosened so you can move it back about an inch . Valid point on the AC compressor it does make it easier though especially if you’re removing the complete front end assembly.
@mikeb2836
3 жыл бұрын
@@sharpcarco I wasn't sure if they had to come out or just lose so I removed them to be sure. Btw great video, one of the only ones and definitely the best for pulling it out the top. Did mine and a junkyard removal using it as a guide. It really looks alot worse than it is stripping the front end.
@sharpcarco
3 жыл бұрын
I definitely definitely agree with you there I’ve personally found the job to be very straightforward and simple the first time I did it. Personally the last time I did when I made a complete video of it but I did not edit it yet it’s going to be much more comprehensive obviously longer but going to Highlight the different problems with getting them out but I did not mind doing it at all
@troywhite76
Жыл бұрын
Glad I found this. I'm in Lansing and trying to find someone to do an engine swap in a 2011 Traverse. Ill be calling you guys next week.
@sharpcarco
Жыл бұрын
Wish I would’ve seen this before nine days after you posted it I would’ve told you not to do that…. Hope you didn’t take it there.
@DodgemanSlease
2 жыл бұрын
I just pulled the entire cradle with engine and trans at work. Why didn’t I find this video sooner!! Also here because the one vac line I can’t remember where it went. But this helped non the less. Thank you!!
@techsir8866
Жыл бұрын
Have been working on these vehicle for years. If you have a lift like they did in the video, just put the powertrain on jacksrands and seperate the engine/transmission. This looks just as painful as the official way.
@sharpcarco
Жыл бұрын
Personally, I haven’t done a BILLION of these, but I’ve done probably 10 on the lift and probably can offer the lift. I kind of like doing them off the lift. It just seems to be simpler to me anyways.
@bearsfan2085
3 ай бұрын
I’ve replaced a Ford 3.5 in an Edge and Fusion this way. I don’t have a lift so have to figure out these ways. Also did this with an Escape too. Can be done.
@elmarko9051
Жыл бұрын
I was thinking no way for a 3.6 to come out the top. I've done 3.5, 3.4 pushrods in Rendezvous and the old GM minivans out the top. You have a removable core support, that makes all the difference!
@1kory883
4 жыл бұрын
Thanks for making this video. Done more of these then I want to remember, out the bottom of course . Don't have a lift anymore and need to replace a engine. Was going this route anyways but it's nice to see other guys doing it. Just stumped why you would not drop it out the bottom, you have it sitting on a lift already lol. Anyways thanks
@sharpcarco
4 жыл бұрын
Because these guys never had lifts before... A year ago and Al (The guy doing it in the video) never removes anything from the bottom because it all has to be tore apart anyways to be rebuilt. But that’s a very good question now that you mention it so thank you
@1kory883
4 жыл бұрын
@@sharpcarco once Al does it 2 times out the bottom he'll have it down in under 45 minutes guaranteed. Just set the cradle on 4 Jack stands, nothing moves and bring that lift straight up.
@edoubletwice
2 жыл бұрын
I learned alot from watching AL you rock
@wraprock-itroll-francisfra9370
2 жыл бұрын
im working on a 2012 chevy traverse 3.6l , thanks yall much needed information. Jackson MI
@sharpcarco
2 жыл бұрын
You're very welcome! Always glad to help another Michigander (If I can, I don't know everything but I know a lot!)
@assignedname9602
10 ай бұрын
This is a awesome video very accurate for this whole job. However, I don't see where the transfer case needs to be disconnected.
@sharpcarco
10 ай бұрын
It doesn’t and this particular vehicle was Front wheel drive only however You only have to separate the transfer case you do not have to move it out so all you have to do is remove the bolts and move it an inch .
@assignedname9602
10 ай бұрын
@@sharpcarco thanks for the reply and posting the information 👍
@shadoww-px1wl
3 жыл бұрын
very nicely done..,thanks so much!btw about how much the labor cost would be?..idk if its stupid to ask but if i would only to replace piston rings, i would still go o thru these tedious process??? thanks Godbless
@sharpcarco
3 жыл бұрын
Sorry don’t get prices out over my KZitem I would assume if somebody charged you less than $1500 at a license to repair facility you’re doing OK…..
@jdubsteachings
2 жыл бұрын
It bills about 13 hours, so it depends on the Rate. If you have to rebuild it then it bills nearly 30 hours. UT used engines for these are really pricey
@claudebeauchemin2134
2 жыл бұрын
Now that's what I call excellent work, love the guy with the cigarette :) very talented
@sharpcarco
2 жыл бұрын
Yeah Al is a bad ass I just wish Accurate Engine was a lot better at what they do
@muwahh98
Жыл бұрын
Going to be putting a LFX in my traverse instead of the same crappy LLT. This video is a great help
@banditsbc75
2 жыл бұрын
He is a freaking Machine! Great video!
@Earl52000
3 жыл бұрын
About to do 1 at the shop dad always wants to frame it but this is how I like to do them thanks for video
@LSXperts72
3 жыл бұрын
Lol that’s completely the opposite with my dad I always wanted to drop the frame and he wants to take it from the top
@codycargill4521
Жыл бұрын
Thank you, pulling the same motor from my Camaro and this really helped👍
@sharpcarco
Жыл бұрын
Wow, I didn’t know they put that piece of crap in the Camaro…. I guess that makes sense now that I think about it.
@ROSSCO2250
2 жыл бұрын
Do you have details on how the oil flow system is on these engines. Trying to better understand the lubrication failures that kill these engines. Thanks love your vids
@sharpcarco
2 жыл бұрын
Well the biggest problem with these engines is cam clearances, as the engines get older the cam bearings were down the oil pressure decreases inside the engine not actuating the VVT solenoids correctly hence the reason they’re such a junk….
@ROSSCO2250
2 жыл бұрын
@@sharpcarco 👍 thanks I wondered about them cam "bushings" lol they are quite a joke. Is this one of the normal procedures they would do( resize/line hone) when reconditioning these heads?
@sharpcarco
2 жыл бұрын
Some places will but places like shit ass Accurate Engines don’t have the equipment to do it and if you do have a line hone like that which will fix the clearance problem indefinitely it is very expensive I would imagine right around six to $800 per cylinder head but probably worth every penny of it. Since the bottom ends of them don’t have that many issues
@scottbrinkley3079
2 жыл бұрын
I'm doing an 10 Buick enclave. Same thing you got there I was wondering which way was better.
@sharpcarco
2 жыл бұрын
Personally I love doing them through the top I think they’re simpler. But some guys are used to pulling the sub frame out and I just found it easier to work by myself with it coming out through the top
@barkoband4477
2 жыл бұрын
ALL HAIL THE KING!!! Thank you guys
@brianosbment2343
2 жыл бұрын
I need a motor replacement here in Colorado. My motor just gave out Friday, in my Traverse. I have paint jobs to get to and now I can't. I can't afford to fix it or buy a new vehicle. It sucks cuz I just started my painting business 5 months ago and was building momentum.
@newme6382
2 жыл бұрын
Where are you located? I just spent my life savings on a 2011 traverse and it broke down two days later. Mechanic says it'll cost 8500 to fix. I fell lost and don't know what to do.
@sharpcarco
2 жыл бұрын
Yeah people know that these are pieces of crap and yet they still sell them to other people that are not aware of it. Anyways I’m in Grand Rapids Muskegon Michigan I don’t know if I can help you but you can reach out to me on my clays AC and auto page like I say at the beginning of the video and send me a DM
@timeandmaterialsdanforth5511
6 күн бұрын
The employee at the shop I just started at tried to do a swap on a traverse and failed. My next car on the hoist is that traverse.. It's a mess. Lol
@curtisyoung4028
14 күн бұрын
That was awesome!!!!!
@Mouser74
Жыл бұрын
If you dont have a lift yea you have to from top. Its way faster to drop engine and trans from the bottom. The traverse was designed to drop from bottom you guys have a lift makes no sense to take out from top. Believe it or not at my shop its a competition to drop the fastest and 45 mins is the record right now.
@sharpcarco
Жыл бұрын
Because we rebuild the engines
@Mouser74
Жыл бұрын
@@sharpcarco yea its still easier from the bottom you guys have a lift and the traverses is designed to drop from bottom doesn't make sense to do extra work and time from top dropping from the bottom is so easy and clean
@sharpcarco
Жыл бұрын
It may very well be, but You Tube is catered towards people at home they watch more videos than guys at shops…. So when I make videos, are they sit around people doing things in your driveway not doing things at the shop where they have the ability to use every single tool on the planet … another words good for you guys… I’m glad it’s easier for you that way
@timothyschaefer4237
9 ай бұрын
What if you can't crank the engine over to get the bolts out of the between the transmission
@EH-cn4rs
Жыл бұрын
Hi Clay..Al your a genius. Everyone says can't be done from top ..pretty much there. My question is if engine is seized it came apart when transfer case losend..if crank shaft not spinning how do we deal with torque converter if not budging? Can it be pulled if torque converter won't budge? The idea was to take oil pan off since everything is screwed and manually turn crank..I feel like it's a big shit show but thinking can be done. Thoughts???
@EH-cn4rs
Жыл бұрын
2010 Chevy Traverse 3.6 crap engine
@leesanta8807
3 жыл бұрын
Thanks for video very helpful ; on 3'6 2011 do you have to replace main bolts and rod bolts when putting crank back in engine block?
@sharpcarco
3 жыл бұрын
Well I know Accurate Engines never do..... then again you could just read their reviews, personally because I am able to do this work myself I probably wouldn’t. Waste of the money but I’m not gonna recommend that to everyone sorry wish I could answer your question
@leesanta8807
3 жыл бұрын
Thank you Clay just wanted you expert advice on these engines it sounds like i will be ok reusing them
@sharpcarco
3 жыл бұрын
Yeah it probably won’t hurt anything
@WisdomInExperience
Жыл бұрын
Thank you. Nice video and detailed explanation!
@sharpcarco
Жыл бұрын
Thank you
@napoleon0521
10 ай бұрын
Great video! Thanks for the info! But the constant pointing gestures at the camera is a bit annoying.
@justinbearinger1989
3 жыл бұрын
My mother has a 2011 chevy traverse it ceased up thinking about getting another one to make it run agian
@sharpcarco
3 жыл бұрын
That will require you remove the transmission at the same time…. So that we’re all require it coming out through the bottom you will still remove the front end so you’re able to slide it out without having a Lift unless you Can use one. I’ve got one tore apart inside my shop right now. If you wanna message me on clays AC and auto repair on the Facebook messenger I can possibly make a little video description and send it to you that way or I just noticed there was a guy that had an hour and a half long video showing you how to do it . Although I wasn’t quite sure why he removed the transmission at the same time maybe his engine was locked up like yours I’m not sure
@C8Kid
3 жыл бұрын
Thanks Albert 👍🏾
@ronaldgann6844
2 жыл бұрын
We have a 2012 Traverse with a 3.6 that ran low on oil so the timing chain is bad, etc..Decent vehicle otherwise...Looking for options...Found a wrecked 2014 Traverse with same engine that runs good...Wondering if it is compatible?...We have a local mechanic who could swap them out if so...Considering other options and saw your video...If we bring the vehicle up to Grand Rapids from Northern Indiana, can you give us an idea how much you would need to either remanufacture it or replace it with a good engine...?...Please help...thank you
@superdave103harley
2 жыл бұрын
Epic victory boys!!!
@ChrisSmith-me4ow
2 жыл бұрын
Can you take out a transmission the same way as you did the engine
@sharpcarco
2 жыл бұрын
More than likely I would presume you cannot do it that way you could remove the engine then remove the transmission the same way but I don’t think you could remove both of them at the same time actually I’m fairly certain of it sorry to say.
@ChrisSmith-me4ow
2 жыл бұрын
@@sharpcarco I have too do it on the ground I don't have a building to do it I have to jack it up then
@yokasmith615
2 жыл бұрын
I have a 2011 buick lacrosse cxs fwd 3.6l. How much to replace the motor?
@sharpcarco
2 жыл бұрын
For the motor and labor probably right around 7000
@jdubsteachings
2 жыл бұрын
I'm doing one right now but he doesn't have that kind of money so as long as the block and heads are OK, you can go in and replace only what's bad. I've had alot of success with that
@sharpcarco
2 жыл бұрын
That’s good information, I know what the asshole over at Accurate Engines charges and that’s what I was quoting him I don’t personally even do retail repair for people so that’s not my personal number you are correct sometimes you have some luck with just replacing things the real problem is the cam journals weird down in these engines then they lose oil pressure. That’s been my experience
@urbanlumberjack
3 жыл бұрын
Awesome video!
@2eagle86
2 жыл бұрын
How would you do that if the motor is locked up?
@sharpcarco
2 жыл бұрын
You don’t…. It Hass to go out the bottom if that’s the case
@josedominguez2706
8 ай бұрын
Would this be similar on a 2012 buick enclave?
@sharpcarco
8 ай бұрын
Damn, near identical
@luiscasiquezuniga3054
2 жыл бұрын
I would like to know how much you charge for that job
@jmiol74
3 жыл бұрын
Nice video.. Good to know it can be done from the top... Do you know if the 2010 traverse engine and the 2015 traverse engine are the same engine? and if they are not, what changes they have, the pictures i have seen from both of them look the same.
@sharpcarco
3 жыл бұрын
There are small little differences the biggest of which would be the fuel injection system the fuel and direction system on the older engines is not Direct fuel injection meaning the cylinder heads will be different. I’m not sure what year they started doing that it may have been 2011 or 2012 but it could possibly be 2010 as well
@jaredfee4834
Жыл бұрын
I have done the research on this very same issue as I am doing the same thing. The long block from 2009-2017 is the same in a traverse. Reman long block engines for them cover 2009-2017. You just have to swap all of your bits and pieces onto the newer engine from the older engine. They are all DI, VVT engines, idk why The Clay Way is saying they aren’t.
@saraflores9601
4 жыл бұрын
That guy definitely earns his paycheck.
@sharpcarco
4 жыл бұрын
He does he’s kind of a bad ass.... This guy makes things look simple that would be extremely difficult for me
@boulregaurdgibson9444
2 жыл бұрын
Help! I took your video and applied it to an 08 Pontiac Torrent GXP. We were all good till we found it's core support doesnt unbolt and heads are to wide to come out the top. Anyone have a miracle cure for my dilemma?
@sharpcarco
2 жыл бұрын
Oh shit I was wondering about the GXP
@RideaKawasaki77
2 жыл бұрын
Thank you so much fir the video. I was wondering if tranny can then be removed from same hole in the front. I need to do a tranny swap on an 2013 Traverse AWD. I don't wanna figure out how to get vehicle 4 feet up in the air to remove engine/tranny/sub-frame from bottom. Thanks for any input. God bless.
@YourAverageFNAF_Edits
2 жыл бұрын
Yes a can be done check this video at 1:14:00 kzitem.info/news/bejne/lo2VrHubk6CimoY
@kimmotley2534
5 ай бұрын
Wonderful event. Wow! I don't live there.
@williegillie5712
3 жыл бұрын
This guy must follow Eric from South Main Auto. He says the same thing after his videos. “If I can do it you can do it”
@sharpcarco
3 жыл бұрын
I will guarantee you that I said it well before they did my channels been around since 2010 and I’ve said it in every single video sense....... So more than likely they learned it from me ain’t nothing wrong with that imitation is the greatest form of flattery
@valeferto8239
3 жыл бұрын
That was f!$&/ awesome 👏 thanks for all the tips
@michaelneedham9124
3 жыл бұрын
Hey man how would I find ur prices I have a traverse that need needs engine I have it I just don’t know anything about engine an don’t wanna mess it up
@sharpcarco
3 жыл бұрын
Well you can always reach out to me on clays Ac and auto repair on the Facebook messenger you can direct message me there. And if we end up doing business I will give you my number to contact me etc. etc.
@adrianaiello3212
3 жыл бұрын
Great video. Definitely a good option when you don't have a hoist available. Does this procedure work on a 2011 captiva with the v6 in it?
@sharpcarco
3 жыл бұрын
This worked on a 2017 GMC Terrain with a V-6 in it so I would have to assume that it most definitely would in that situation. I didn’t know they made the Captiva in 2011. You learn something new every day
@adrianaiello3212
3 жыл бұрын
@@sharpcarco I'm in Australia where we have a Holden captiva since 06 but they are the same car with a different front frille. They later become what I believe is the equonix but over here they are still called captivas
@mypony7310
2 жыл бұрын
Free pickup, WOW! I didnt know people charged for that
@sharpcarco
2 жыл бұрын
Yeah I don’t know of anywhere that comes and picks up your vehicle for ….. well I guess the dealership can do that since they’re charging like $185 an hour…. And I’m pretty sure it means pick up your engine not your vehicle. Although I have known Accurate Engines to do that in the past just depends on where it’s at
@jimthompson7035
Жыл бұрын
Great video, Al is a beast, buy him a beer for me :} . Can i also remove both the engine and transmission at the same time to keep them connected? I bought a damaged (side) 2020 Traverse and cannot repair it, so I want to keep all the front end parts for another project but remove the engine and trans to sell Lost a lot of money on the car so I want to sell it as a unit to get more (only 19K miles on it) . Thank you
@geraldito7777
4 жыл бұрын
Nice! How many hours will be that job sr? Thanks!
@sharpcarco
4 жыл бұрын
Well I talked about that in the video, i’m assuming you missed it. It takes us about five hours to do one I have no idea about your competency or your skill level.
@randyusmc
3 жыл бұрын
@@sharpcarco so going out the top is about a 5hr R&R vs the 11hr book time out the bottom?
@sharpcarco
3 жыл бұрын
I’m not kidding when I say Al can do this in about 2 1/2 hours if not quicker removing it from the top but I’m definitely not Al I would think it would take me five hours to remove all of that stuff and remove the engine if not longer and I would never in 1 million years “anybody only five hours of labor time to remove the engine I would be out of my mind…….. I would “book time and then I would probably add a couple hours to it my rule of thumb is when the book says anything over five hours I add 15%, but I’m also talking about jobs that I don’t do every day so there’s that
@ricardomartir1906
Жыл бұрын
Where you guys located
@jorgesolis6589
4 жыл бұрын
Awd traverse 2010 its posible too remove the engine like that
@sharpcarco
4 жыл бұрын
Yes it is but you need to leave the transfer case loose when you go to reinstall the engine.
@shawnshurtz9147
Жыл бұрын
It's been converted to a Cadillac nice.
@gilbertauto6882
3 жыл бұрын
How about if it’s AWD
@Transient901
3 жыл бұрын
is this an AWD vehicle?
@mrvang8077
28 күн бұрын
This is why I hate engine that is cramped and super narrow. And why I stay away from vehicle with squish engine compartment.
@sharpcarco
28 күн бұрын
I find when I do this Engine or these types of engine and these types of vehicles they’re actually simpler than doing another ones. Just my opinion, especially when I do it this way.
@romaniac87
7 ай бұрын
Thanks!
@bobocaterpillar3697
4 жыл бұрын
good luck getting all that wiring back in place. out the bottom is MUCH cleaner.
@sharpcarco
4 жыл бұрын
We probably do it three times a week.... The point of the video was for people who do not have a LIFT! ... You probably missed it when you were skipping through my video for whatever reason
@luiscasiquezuniga3054
2 жыл бұрын
How much Will it be for that job
@sharpcarco
2 жыл бұрын
I’m guessing Accurate Engines probably charges about $1500 to do that job
@sharpcarco
4 жыл бұрын
Carpets looking pretty b ad in your Traverse? Check out this video where we show you how to make it look NEW again CHEAP! kzitem.info/news/bejne/t3uBq6GseqRllqw
@henamondol9675
Жыл бұрын
I need help with my vehicle please!🙏🙏😢
@NOOR5083
2 жыл бұрын
Where do you locate guys plz
@timmyrollins2994
3 жыл бұрын
Wish you guys could fix my 2010 Chevrolet traverse.
@sharpcarco
3 жыл бұрын
I don’t know if accurate can , but I could. I’m not over there working with them any longer my contract came up and I decided to not renew it
@seanflanery3324
4 жыл бұрын
Accurate engines is a shady place, had a motor rebuilt by them and it didn't even last 2500 miles following their break in procedure to a t. Went through a whole process only to find out the warranty I had didn't even cover it.
@sharpcarco
4 жыл бұрын
Well regretfully I’m sorry to hear that, I don’t work for accurate engines, all I can say is the things that I’ve seen is that Lanny seems to take care of people but I do not watch his every move so I have no idea. I know the people that work in the back where I repair my automobiles are really stand up guys and do very very good work as far as the engine building part I don’t know I don’t work with them guys every day. I’ve seen Lanny cover things that I would never have covered because they were the responsibility of the customer and nothing that they did wrong but you never know. But if you want to tell me the situation I can give you my unbiased opinion.... and since I work with them every day I may be able to help you if there’s something that they can do.
@kendallsangchan3559
Ай бұрын
How about putting it back in? Lmao cuz I’m having a hell of a time getting mine back in
@sharpcarco
Ай бұрын
Easier than taking it out . Did you have A AWD?
@kendallsangchan3559
Ай бұрын
@@sharpcarco yeah all wheel drive and part of the block hits on the transfer case lol so im thinking imma have to just drop the subframe to get it in it’s a pain lmao rebuilding the whole engine was easier then getting this back in and with the flywheel barley fitting in the bell housing it really makes shit difficult
@kendallsangchan3559
Ай бұрын
@@sharpcarco oh yeah it’s a Buick enclave too lol but I got it figured out lol undid the transfer case moved it about half a inch and was able to get them together
@sharpcarco
Ай бұрын
@@kendallsangchan3559 I really thought we said that in the video. I’m almost certain of it because it’s a critical part but it doesn’t have to come up. It just has to move back as you already know.
@kendallsangchan3559
Ай бұрын
@@sharpcarco yeah it was like like 5 bolts 2 on the bottom and 3 on top I just loosed them up (not take them out) and scooted it over and that’s all she wrote I’m shocked that even got it out without loosing them lol anyways that’s the way u can do it without dropping the sub frame
@nandoontiveros4872
2 жыл бұрын
I love you
@sharpcarco
2 жыл бұрын
☺️
@luiscasiquezuniga3054
2 жыл бұрын
Quisiera saber cuanto se cobra por ese trabajo
@pollolealgracia5158
Жыл бұрын
1800 te cobro yo y no tengo que hacer todo eso que hizo el si tienes el gato que sube los carros… mucho trabajo de embalse hizo ese man la neta no bueno 🤦🏻♂️🤦🏻♂️🤦🏻♂️
@williammendoza5358
Жыл бұрын
Very hard
@sharpcarco
Жыл бұрын
Well it depends on your perspective but yeah I can see how it would seem difficult I personally enjoy doing it this way.
@mrvang8077
3 ай бұрын
This look like it's from the 1st gen traverse.
@sharpcarco
3 ай бұрын
Doesn’t really matter still pretty much the same procedure
@davidjones7372
2 жыл бұрын
How
@timbowers1
3 жыл бұрын
Im working on swapping a ls4 into a 2010 traverse now the 3.6 are junk
@sharpcarco
3 жыл бұрын
That’s pretty cool Tim let me know how that goes if you send me pictures to my clays ac and auto repair Facebook I will post them on my site
@alexanderalexander6169
3 жыл бұрын
Id like to see this.
@justinstatham6378
Жыл бұрын
Did you ever make it happen?
@rolex4130
13 күн бұрын
I got one engine going not working bring $700 and take car
@sharpcarco
13 күн бұрын
Where is this car at? I have a good engine for one of them. What year is it?
@frankie.b.s9133
11 ай бұрын
HOW SWAY😮 HOW
@chipdibble1264
Жыл бұрын
Als getting ripped off.only paying him flatrate.should be paid by labor guide
@sharpcarco
Жыл бұрын
Most definitely… but he makes about $1000 a week and he’s always got a job to go to so I guess it depends on how you look at it. But yeah, Lanny is a real POS….
@melissaboyer7428
2 жыл бұрын
Putting a little too much trust in those aluminum threads by chaining up to the intake.
@sharpcarco
2 жыл бұрын
Well if you look up the depth of the bolts versus the thread pitch….. Well anyways the guys been doing that for 18 years so I don’t know
@kurtbottcher9811
4 ай бұрын
How not to do it video.
@sharpcarco
4 ай бұрын
Oh, I love the haters….. You know you mad’er
@sonny2435
Жыл бұрын
THAT, is removing it out the front; `out the top means leaving the front clip on ! what an over engineered plastic spaghetti factory ! This is why DETROIT is a slum-ghost town and Kia, Hyundai, VW are killing it
Пікірлер: 158