If only the supplied instructions were this clear.
@danyf3116
2 жыл бұрын
The address of this video should be added in the reference part of the badly translated manual. I'm keeping this link for future reference. Kudos man. ☺
@IngridsVanlife
2 жыл бұрын
thanks for the great advice, hope I can have my diesel heater back up and running soon!
@crozzy28
7 ай бұрын
I have had a intermittent fault with my heater since I bought the van! The guys who built the van fitted a off/on switch so the heater controller wasn’t lit up all the time the odd time the heater would run ( just cold air) without turning the heater on I just pulled the plug apart (the controller board to loom) just because it was easy to get to. The heater as always worked fine when needed I just push the connectors together on use the heater as normal. But just been away this weekend and every time I connected the cable together the fan ran blowing cold air thee we n turned the control panel on but couldn’t get the heater to run and error code E-o7 is showing have you any thoughts thanks in advance
@kr3392
Жыл бұрын
Thank you for a really good video👍, i have a fault code E17 and i cannot find anything on internet do you know what this code means??👍
@codprawn
2 жыл бұрын
I keep getting Error code 01 - low voltage. Using a mains 30 amp supply. This is my 3rd heater - first one ran over 4000 hours on kero no problems. Then it stopped working. Bought another as they are so cheap. Turned out to be just the controller! Anyway the new one is on the same setup. Could it be this one is a bit more sensitive and needs a bit more than 12v? Happened 4 times today. Turn it off - back on again - fine for a while then it trips out again. Very annoying.
@vanlifesurvivorsguide
2 жыл бұрын
Are you sure the transformer is set to 12v? how far is it from the heater and what size cable did you use to connect the heater to the transformer? did you bridge 2 of the channels on the transformer or just go through one?
@codprawn
2 жыл бұрын
@@vanlifesurvivorsguide Thanks for the reply. It worked fine with the last one same setup. Bridged 2 channels. I can understand it on startup when current draw is highest but not during normal running. I will test the voltage tomorrow. Perhaps the pot needs a tweak for this one.
@vanlifesurvivorsguide
2 жыл бұрын
@@codprawn have you checked the controller is set to 12v and not 24v? This sounds most likely if it is the same set up as before.
@codprawn
2 жыл бұрын
@@vanlifesurvivorsguide Same controller as before. Will check but unlikely to have changed?
@vanlifesurvivorsguide
2 жыл бұрын
@@codprawn where are you based?
@Roger_Gustafsson
Жыл бұрын
E02 if power is low too it seem. Edit. No, it's not related to high voltage. It's something else.
@karenjackson5733
3 жыл бұрын
I may need to save this for future reference!
@user936
Жыл бұрын
I'm currently playing a game to see if I can get the whole set 🙄
@johndavis8655
2 жыл бұрын
A concise and well presented video giving valuable information without the poor sound quality, blurb and waffle often found in similar video's I've seen.
@scottjones9602
3 жыл бұрын
Excellent and comprehensive video, definitely one to keep for future reference. 👍
@vanlifesurvivorsguide
3 жыл бұрын
thanks scott
@WarthogARJ
2 жыл бұрын
Thanks, well made video. Especially listing where the codes are in the video. Makes it very easy to get info from.
@reacohn751
2 жыл бұрын
Cracking video with great no bull explanations and demos of appropriate areas. Nice one.
@xingchao9125
2 жыл бұрын
Now thats how you make a youtube video. You're a bloody legend mate.
@vanlifesurvivorsguide
2 жыл бұрын
Thanks mate
@raykeogh1972
2 жыл бұрын
Brilliant very informative video. Oh I have had overheating sensor on a few times and after watching this this now think it’s the bend in the airflow to distribute the heat around the van. Bad planning on my behalf. Thanks again Ray K UK YNWA
@cassandrasheridan7346
2 жыл бұрын
really helpful in time of need. Thank you for a genuine public service video 👍
@vanlifesurvivorsguide
2 жыл бұрын
No problem, glad you like it
@paulbrown521
2 жыл бұрын
Brilliant explanation , no messing , blurb ,or crap ,Thank you .
@vanlifesurvivorsguide
2 жыл бұрын
Thanks mate and no problem you are welcome
@johnpowell5433
10 ай бұрын
I saw that Kerosene is non-lubricating on another channel and they suggested adding a few drops of 2-stroke oil to your tank. Whaddya think?
@vanlifesurvivorsguide
10 ай бұрын
Hi mate, it is actually not necessary. The best thing to do is mount the pump at a 90 degree angle unlike mentioned most places. Then you should be fine. Mine has been going 4 years strong on Kero. We made a full video on it please check it out. It won't let me post the link here but it is called diesel heater fuel angle or something very obvious.
@johnpowell5433
10 ай бұрын
@vanlifesurvivorsguide: Cheers for that, I'll watch the video. I bought a TriClicks "8kw" heater back in March but haven't installed it yet. It has the filter/moisture trap that you recommend in the Buyers' Guide video but I'm not sure which controller is the crap one. I've got the one you did a video on, the three-bladed with spanner type.
@Myhealth-ce2se
10 ай бұрын
replacing motherboard and lcd is about 20 quid. how is that more expensive than buying a new heater?
@Warren007
8 ай бұрын
Just another thing worth mentioning for E01 that I've just fixed - I accidentally plugged the heater into 240v(the plug was identical to the one that goes into the unit and the transformer) and I fried the unit. After replacing the circuit board I was now getting E01 error despite there being enough voltage & amps for the unit. In my case, I had to replace the display/control which removed the E01 error. Goes without saying, don't plug 240v into a 12v unit!
@carpetsrugsandupholstery
Жыл бұрын
Hi , I'm getting an 0 2 error code but my display shows that its receiving 11v any ideas please
@vanlifesurvivorsguide
Жыл бұрын
The battery is too low it should't be discharged lower than 11.9v. So it will be a phantom over volt error code and really an 01 error code. You battery might need replacing too it might be permanently damaged too
@pstoneking3418
8 ай бұрын
I've recently purchased a Chinese diesel hearer. I've found one thing that can cause an E10 error is using too small Guage wire. I connected it to my 12 volt batter that was approximately 30 feet away using 18 awg wire. Everything appeared to be normal until I realized that the fuel pump wouldn't run with the voltage drop caused by too small of wire. After I ran 12 awg wire Everything was fine until my battery got too low and caused a E8 error. For best results, If possible connect the battery using the supplied short cable else use 12 awg wire and keep the distance as short as possible. Don't use a power supply or ac to dc converter. You can use a battery with a trickle charger without any errors.
@RobBob555
2 жыл бұрын
Error code E-01 *tip* ..if I try to start the heater above 15 degrees c I get the error E-01 BUT 15 degrees or below, it starts fine..once heater is running I can turn the heat up no problem..
@austinhembree8197
Жыл бұрын
I am getting error code 2 but I have my heater hooked to a 12 volt battery. Was working fine, shut it off and then kept getting error code 2 on next use. Any suggestions?
@jacobernst3753
8 ай бұрын
Regarding to much heat at lowest level- I have mounted a fuelpump from a 2kW on my 5kW heater, and it works fine, gets more economical too 👍
@Ralphs-House
10 ай бұрын
E-01 error code on a Chinese diesel heater will also come up if the octane rating of the fuel is too low (ie if you have veg oil in the mix) and it will refuse to fire up from cold as a result, shutting down and throwing the code along with a fuel icon. Its important if you do run mixed fuel, that you always run straight diesel or kerosene at full pelt shortly before shutting it down (and when starting) to purge the fuel line of any oil and to clean the glow plug. These heaters are less fussy when hot and will happily burn a mixture. When cold its a different story. If you do end up with a mixed tank and unable to start it, you have to syphon the tank contents as much as you can, replenish with a measure of neat diesel or kerosene, attempt to start it a few times and once it does, get it up to temperature quickly and then put back what you drained out. Restarting will create a cloud of smoke until all the oil is burnt off through heater and exhaust but should soon settle down. A solution is to have a switch-over tap so you can switch between mixed and straight fuel sources to avoid this. E-01 error is nearly always low power from battery or transformer - EXCEPT when it also displays the fuel icon. In this case its telling you its unable to ignite the rough fuel rather than having power issues, but will still throw an E-01 code. Hope it helps someone!
@PunctualMrSmith
8 ай бұрын
Hey I am getting e01 but it is from my boats diesel tank. It’s been working fine but it’s currently extra cold. I am getting a small voltage drop of about 0.4 v once started. On the remote it shows a fuel symbol so I am wondering is it because the system is too cold and the small voltage drop is not able to get it going? Thanks in advance
@paulscussel140
2 жыл бұрын
Best explanation of error codes I've seen, thanks for sharing!😃
@SuperXs1100
2 жыл бұрын
Decided to by one, and keeps throwing p-01 code on 12v, 24v, new batteries, with charger on them and is reaching required power levels per the manual. Even added some juice to see if it would throw a high voltage code but never did. What controller and board would you suggest to get for this just so I have a piece of mind?
@vanlifesurvivorsguide
2 жыл бұрын
Hi mate, there isa motherboard and controller and remote set in this post we recommend. you will need the 5kw motherboard and then we suggest the blue controller with the red remote as the best option for controllers www.vanlifeuksurvivorsguide.co.uk/post/chinese-diesel-heater-spare-parts-added-extras-upgrades-2-0
@brownbunny2513
2 жыл бұрын
December 7th 2021 One year & one month since I brought my chinese diesel heater, I went to turn it on , and heard "Click", with no heat, no sound, no light on the controller. I am saying all this to say "Thank You",for making this video.. After watching your video, and a few checks with a multimeter I figured out that the controler was gone. I did as you recommended and brought another diesel heater.( cause just the ECU, may cost more than the whole heater) With alot of praying and patience I got the plugs to fit into one another, installed the ECU, and changed the controller. The controller has to match the ECU, or you'll get the E-07, code. Thank you!
@lavaner-WeManufactureComfort
3 жыл бұрын
The most comprehensive and clear instructions video I have ever seen👍
@vanlifesurvivorsguide
3 жыл бұрын
Thanks mate, glad you liked it!
@alirezamoafi8321
2 жыл бұрын
Hi Ive just got a van with a car parking heater BSE - D5 was working but now giving error 7 and it keeps reating "fan failure^ . Please advise what can be done to fix or remove / to disconnect. Thank you
@vanlifesurvivorsguide
2 жыл бұрын
I think the D5 is an eberspacher heater and have different codes but if the fan is the problem please check out error code 6 in this video. Is it possible something has been sucked into the fan end of the heater and is obstructing the fan?
@LukesVanLife
2 жыл бұрын
Like the vid buddy! Nice one. I'll be referring people to this vid 👍👍
@vanlifesurvivorsguide
2 жыл бұрын
Thanks mate :)
@jameskim62
5 ай бұрын
VERY GOOD INFORMATION AND EXPLANATION!!!!!!!!!!!!~~~~~~~~~~ 12 SUBSCRIPTION ON YOUR WAY.....
@johnhansen337
Жыл бұрын
Textbook video for folk who live with the machines and who fix them. Oration was perfect.
@vanlifesurvivorsguide
Жыл бұрын
Thanks mate :)
@johnhansen337
Жыл бұрын
@@vanlifesurvivorsguide I will be polite and say that the Chinese engineers have a sense of humour as they make sure we spend lots of time fixing their kit without manuals, and using a jungle telegraph system of teaching. I have just given up on a unit which failed on a fan error. It completely filled the boat with thick smoke which took weeks to clear of odours. After buying a replacement board and sensor, mating the controller to it by altering the voltage to 12v, swapping the sensor and fan plugs round, and moving the fan earth lead to the outer pin, the little bugger booted up and warmed up nicely. It soon began to speed up the fan then an almighty crunching sound occurred and the fan error code came up and the unit went dead in a cloud of smoke. It now starts at full fan speed and fails in 3 seconds. Time to give up and place the unit and its parts in the "suspect spares" bin. 😕
@8DHealth
2 жыл бұрын
So... If you over prime the heater ,what do you do ? Just wait?
@vanlifesurvivorsguide
2 жыл бұрын
Hi sorry only just seen this, the best thing to do if you have over primed it is take the fuel line off of the bottom of the heater put it into something (so you don't get diesel everywhere) and try and start
@bennym2893
Жыл бұрын
Thanks mate, great no nonsense video. I have just purchased one of these from Vevor. Got it all set up in my shed last night, running off a next to new motorcycle battery (temporary whilst I wait on my inverter) I'm getting an e 2 fault with this though which seems strange, and you say it's most unusual. Anyone able to chime in what this could be?
@heloisecockenpot
Жыл бұрын
got today after installation a e-2 with a vevor like you. anything to help me?
@bennym2893
Жыл бұрын
@@heloisecockenpot hello mate, once I put the power inverter in and ran it off of mains electricity It worked perfect after that. Seems the battery I was using wasn't up to the task, which I did find a little strange
@ryanhentschke9090
2 жыл бұрын
E10 means your diesel pump is on too much of an angle, twist it straighter.
@jimholmes2555
Жыл бұрын
What are your views on installing a fuel filter prior to the pump? Nothing fancy, just a paper inline filter.
@vanlifesurvivorsguide
Жыл бұрын
Yeah we always do, there is normally one supplied in the kits
@pvidamour
2 жыл бұрын
I keep getting e10’and nothing I do will start it back up and tips please
@vanlifesurvivorsguide
2 жыл бұрын
Sorry only just seen this. Did you get it sorted?
@dB-uv7wp
4 күн бұрын
Used mine twice. Eo2 fail. I hate these things. Non of them are any good.
@terjehovde6818
6 ай бұрын
Exellent infos, thanks ! You are the best, werry good explainations, grettings from Norway
@alanhill2886
2 жыл бұрын
Thanks sorted out its problem in minutes, inlet screen half blocked with dust , code e 05. Trying to work With manual provided is hopeless
@davemartin2970
5 ай бұрын
Mine stopped working after I moved my caravan so I got a new controller and motherboard, now when I try turn it on its flashing red with 07.. nothing coming on even though I got new bord and controller??????????????????
@Canuck777
16 күн бұрын
I disconnected the power will it was running. It now seems dead. I see now I made a major fault. What should I do? Ty
@a1d3nh0
8 ай бұрын
I have a triclicks (Amazon) heater installed in my van. I’ve only used it 2 times, once when I installed it (for 15 mins) and once yesterday for 10 minutes. The engine temperature says 200 degrees C. No errors but that doesn’t sound right? Also, even after 10 mins it runs the CLEA function when I power it off. I read that it only does that after long use. Is there something wrong with mine?
@lukeangell8357
2 жыл бұрын
I'm getting an E-02 code from a 12v battery. Doesn't seem to go away
@vanlifesurvivorsguide
2 жыл бұрын
Thats weird, is it the same controller as the video? If not what does it look like?
@andrei87cod
2 жыл бұрын
I do have the same error e 2 on 12v battery and same controller
@jimnjele.bean-dayone3505
27 күн бұрын
Thank you. Straight to the point, very clearly explained.
@chrisbenton8842
Жыл бұрын
Just bought mine and am getting errors eo2 . Think the motherboard might be the issue .
@vanlifesurvivorsguide
Жыл бұрын
most likely a damaged battery if a battery is what you are running it off of. Most phantom 02 error codes means damaged cells in the battery. Get the battery load tested as your first move
@chrisbenton8842
Жыл бұрын
@@vanlifesurvivorsguide thank you . I tried a few different batteries but to no avail . I check too with a volt meter . I ca t clear the eo2 code and do anything
@PrisonersNoLongerAccepted
2 жыл бұрын
Excellent info. Thank you 👍
@dylanmartin9190
2 ай бұрын
I have the error 05 and yes my warm air is blowing towards a painted wooden wall about 5cm away. I put 4 individual tubes on the 4 outlets and there's a 90 degree bend as soon as the warm air exits. I will have to cut through the wooden wall soon. Hopefully it will fix it
@colinarner790
5 ай бұрын
Well, here I am standing at the heater at 3 am and keep getting error messages. 30 seconds into the vid I realized I was simply blocking part of the heat line. Thank you sir, owe you a pint
@vanlifesurvivorsguide
5 ай бұрын
No problem mate, glad you found it helpful
@directorstu
6 ай бұрын
Brilliant video. Subbed.
@vanlifesurvivorsguide
6 ай бұрын
Thanks mate :)
@lukeblackwell3740
Жыл бұрын
i have a 12V heater wired to cig fuse but it’ll start then die saying voltage fault check line. Error -02? discovery 1 300tdi
@robertjett5243
7 ай бұрын
I keep getting a e-10 error I can’t figure it out I’ve replaced the glow plug cuz I took it apart and noticed the tip of the plug was cracked and broke, I also replaced the mesh that goes around the glow plug. The burn chamber is clean as a whistle. I only run diesel through this, the fuel line total from tank to unit maybe 2 and half foot. Another issue I’m having is priming I have the red controller I ain’t been able to find others like mine but when I try to push ok and up or on and up or down I get nothing but it seems to be priming on the initial start up and there is fuel all through the line. Any ideas advise and help would be so appreciated thanks again.
@mikeakerstrom1667
Жыл бұрын
Missed a very important cause for E-08. This can be caused by the heater being too dirty to light, meaning that the heater needs to be taken apart and cleaned (or just replaced)
@jamieism
Жыл бұрын
My heater is giving me the error AO3 (or could be R03). Is that the same as E-03? 😭 Help, it’s cold!
@haxor7364
11 ай бұрын
yep ,...code 9,....replaced the censor and it was fixed,.....it was broken after i let the heater running for 1 hour on his hardest( there was code 5 because of air) , to let it clean insite i run it for a bit more than a hour on 6 , after that it always run hot and gives error 9.......the machine was only 1 year old and runs about les than 1000 hours...
@garywatson3102
Жыл бұрын
Do you know what a red circle with a horizontal line means?
@vanlifesurvivorsguide
Жыл бұрын
yeah it just means that the heater isn't running, that is a different controller though you should check out this video. kzitem.info/news/bejne/wqp-u42wb4tehII
@garywatson3102
Жыл бұрын
@@vanlifesurvivorsguide Brilliant, thank you.
@SeeSi
3 жыл бұрын
Very informative. Cheers 👍🏻
@NomadMoto
Жыл бұрын
Mine give me u003 then the screen shuts off. These things are junk
@mcape441
Ай бұрын
Brilliant explanation, no waffling on, Thank You.👍
@lufwendosibuku7071
Жыл бұрын
How do you delete an error code
@vanlifesurvivorsguide
Жыл бұрын
You don't need to, once you fix the fault the code should clear automatically. What code do you have?
@donaldpetrey3064
7 ай бұрын
Are you saving your triclicks dh is better quality then are reg CDH
@joshchapman-s3s
3 ай бұрын
I’m getting error code E-02 Wired directly to a new 12v deep cycle battery?
@mihneaagopian7099
4 ай бұрын
hello, I have a webasto china that was working perfectly and suddenly it didn't start. it turns on and the screen says o n I think and the fan doesn't start. What is that "o n"? it's not an error number I think it says "o n" but it doesn't work
@Roger_Gustafsson
Жыл бұрын
I just got mine and started it up and: E09!!! And what means "a new controller"?
@MrGogogu
2 ай бұрын
Mine gave the 08 error because the fuel froze on a cold night. It tried several times to light , now the screen is dead. Nothing will get it going again
@twosurfersinavan
2 жыл бұрын
Cheers for the advice and saved for future reference
@michealgillman7418
Жыл бұрын
Thanks very much for explaining these error codes. I have now replaced the heat sensor TWICE as the fan just came on for no reason...just my luck, I carry 2 spares now! 🫰 when rectified do the error codes automatically disappear? Thanks again, regards Mick
@vanlifesurvivorsguide
Жыл бұрын
yeah it should just clear once the error is sorted. Do you still have error code 9?
@pstoneking3418
8 ай бұрын
I got an E8 which is a fuel error but was caused by my battery getting too low and wouldn't run the pump.
@claybornedyer7842
2 жыл бұрын
Is there a brand you feel comfortable recommending. Just bought new and won"t start. Fan sticks, E-06.
@vanlifesurvivorsguide
2 жыл бұрын
Yeah check this post out www.vanlifeuksurvivorsguide.co.uk/post/tried-and-tested-diesel-heaters-2-1-post
@paulball1767
13 күн бұрын
Fantastic video no bullshit no stupid music
@aaronmaloney8
10 күн бұрын
Mines say error 02 with glue plug light on
@LorraineJOHNSON-w6f
11 ай бұрын
E10 code I put in 1688 it works, but fan don't switch off
@leorutherford5456
2 жыл бұрын
Great video, very to the point, I had e-10, seems to run fine after the second start attempt
@mrjockey87
Жыл бұрын
Did you just start it again without the primingsequence? Ours starts and shuts off
@calilife805
8 ай бұрын
I wonder if this is happening to me. I have a eco Flo 2 and I ran a heater on it and it hit over 600 watts. Now the heater won’t start. Error 3. And I’ve never ran it !
@husksboat
3 жыл бұрын
Very informative! Great idea about leaving a quarter tank of fuel when connecting into the main fuel tank! Have you got a link for the nylon pipes?
@vanlifesurvivorsguide
3 жыл бұрын
thanks mate, yeah the link is in the description but here you go ebay.us/8gA1HU
@niclazzareschi
Жыл бұрын
Link is expired. Got a new one?
@beccafairclough4617
3 жыл бұрын
Nice one 👍🏻
@colindyer6107
7 ай бұрын
Great video can you help with a problem fairly new heater but now when turning on it runs at very high speed straight away then shuts down
@Evilslayer73
9 ай бұрын
Hi i have a Likaci diesel heater i got an error 03 so i replaced the glow plug and im still having the same damn code what it can be ? the mainboard unit?
@kennethbundy7513
9 ай бұрын
I just watched your error code video. I wish I had seen this much earlier. Very well done, I have immediately subscribed. I do have a voltage question. My controller reads much lower voltage than a direct metered voltage check of the battery. Any suggestions?
@vanlifesurvivorsguide
9 ай бұрын
Hi mate, that sounds like volt drop. So the cable between the battery and the heater isn't thick enough and should be thicker. we recommend 6mm2 (10awg). We also recommend going directly to the battery via the inline fused attached to the wiring loom and not through any other fuse box as this can cause volt drop too :) Thanks for the sub
@rubyred794
Жыл бұрын
Thank you so much for this information. I'm ready to go away but my heater programmer was flashing the little battery in upper right hand corner. It has a separate desel tank. It did come on but only blew cold air for 10mins or so. Now it won't even turn on.. I'm flummoxed. If anyone has any suggestions, please can you let me know. Thank you 😢
@vanlifesurvivorsguide
Жыл бұрын
it sounds like the fuel hasn't made it from the tank to the heater yet. Have you primed it? Also a low battery could be the cause how many volts is is it?
@angelosdovletoglou6911
2 жыл бұрын
It has been working well for 2 years but few days ago started showing E10. The lithium house battery voltage is 13V and fully charged and the display of the diesel heater shows 13V. So that's good. When I start the diesel heater the fan is starting first and slowly the display of the diesel heater shows the voltage to drop from 13V to 9V and then shows the error E10 and shuts down. The Li ion battery display continues to show 13V during all this time and the LED lights are working fine, the fridge also working fine, so no issue with the power coming from the Li ion battery. The heater needs 12V to start so something is happening and does not get the minimum 12V needed from the battery or the heater "believes" does not have 12V. Any suggestions would be greatly appreciated.
@vanlifesurvivorsguide
2 жыл бұрын
What you are describing sounds like either volt drop or damaged battery. Well this happens when the cells are damaged in a lead acid battery but i'm not sure if it happens with lithium though but you could get it oad tested and see if anything is wrong with it. And this is also what happens with volt drop but as you said it has been working fine for 2 years so the cable is obviously thick enough to work without problem. Another thing that can cause volt drop is if you have gone to a fuse box instead of directly to a battery and the cables going to the fuse box are not thick enough to carry the load for everything attached. so if you have added something new to the fuse box or are using stuff at the same time than normal. Do you have a split charge system? have you tried starting it with the van running?
@angelosdovletoglou6911
2 жыл бұрын
@@vanlifesurvivorsguide Thank you for the reply. I use a fuse box and has been working fine. I have not added something new to the fuse box. I have a split charge system, so the 2 Li ion batteries (170Ah each) are charged when I run the engine of the van. I also tried to start the diesel heater with the engine running, but I got the same error and low voltage issue. Also, per your suggestion, how do I load test the Li ion batteries to see if anything is wrong with it? During this process of starting the heater as the display of the heater drops from 13V slowly down to 9V, the display of the Li ion battery stays at 13V and with all the LED lights on, I do not see any flickering of the lights to suggest that the batteries are not working properly. I am wondering if the electronic controller inside the diesel heater is not working properly and when I start the heater it malfunctions and "reads" low voltage and then it shuts down. I am thinking to replace the diesel heater with a new one. Your suggestions would be greatly appreciated. Cheers.
@lawnmowernation2320
7 ай бұрын
How to convert this thing to run off a 18 v drill battery withoutvthe e1 error code
@Lionel-alfredaPlett-edwards
24 күн бұрын
The green soft I s fine from the tank to the pump but not after the pump
@davidloftus1949
2 жыл бұрын
Where can you get the correct white tube to replace the green?
what is wrong with my heater. the fan is always running it dose not try to start or anything.. i have unplug it and this in the past would reset it but now it just runs the fan none stop for days. help please....... the display just blinks.. i have switch the display to my other one and still nothing. help please
@vanlifesurvivorsguide
Жыл бұрын
sounds like the heat sensor, error code 9 in this video. but we have a whole video on our channel about it kzitem.info/news/bejne/12qI3nebrp2FeYo
@williamwilson1816
2 жыл бұрын
very helpful fixed problem , error code 9
@sumwonyustano
11 ай бұрын
Need to update your links, all the ones I've tried go no where.
@austinwhite6645
Жыл бұрын
We’re getting the e-10 error code and the fuel pump won’t even kick on. We’ve gone through three fuel pumps so far - any idea?
@vanlifesurvivorsguide
Жыл бұрын
it might be flooded, have you primed it quite a lot?
@StephPNE
Жыл бұрын
I haven’t got an error code iv got nothing just won’t start up only used it once
@janainamacari2524
Жыл бұрын
Help me. I have a Air heater KM 2.0 and the error is A-5. What is this?
@mythrail
Жыл бұрын
My heater won't start and is displaying a red circle with a dash in it, no other error code. It did have an 08 error the time before last it ran, any ideas?
@vanlifesurvivorsguide
Жыл бұрын
The error code 8 will still be the same as in the video, the red circle is always there when the heater isn't running when it starts it goes. You have a different controller from the one in the video though
@maxthecherryman
Жыл бұрын
Thank you. The clearest explanation yet of error codes. Yes E8 was my daemon and removing the supplied fuel filter made an immediate improvement with a slightly smoky start ( first time )no E8 error after 2 minutes so far and running ok so far been going for a couple of hours no issues. Closed down correctly.
@malachieven446
3 ай бұрын
Thanks!
@vanlifesurvivorsguide
3 ай бұрын
Thanks mate thats our first ever super thanks
@michelthibodeau8550
5 ай бұрын
Useful video, thanks 🙏
@DGCSPEEDSPRAY
2 жыл бұрын
Great video very helpful. I suspect I have flooded the burn chamber and getting e10 as when I prime the diesel alway runs to the bottom of the hose leaving air trapped at the top. How do you solve a flooded burn chamber?
@McKaylaRuesch
2 жыл бұрын
I’m having the same issue, would love to hear if you were able to solve it and how?
@Brad_hodge_photography
2 жыл бұрын
Mine won't work now after I run it dry been a month now can't get it to work 😩 error 8 code keeps coming up
@vanlifesurvivorsguide
2 жыл бұрын
Hi mate, have you tried priming the heater as it takes a few primes to get the fuel all the way from the tank to the heater sometimes. If you haven't tried that will be the problem if you have then it could just be bubbles in the fuel line and need purging. take the fuel line off of the bottom of the heater and put it into a clean glass or similar and run a few full prime processes or until you can see no bubbles in the line then reattatch it and start it up. kzitem.info/news/bejne/1Kl8yoxoqICBaXo kzitem.info/news/bejne/mK2jt5p7oKhqiYY
@Brad_hodge_photography
2 жыл бұрын
@@vanlifesurvivorsguide thank you mate and I have tried that the only thing I have not tried is losing the nut on the actual fuel tank where the nipple is I took the line of at the heater and and primed it and the fuel was dripping out the end so I connected it back up and it just dropped again kinda just sits there in the line pulsing up and down I'm not sure what else to do feel so lost lol
@Brad_hodge_photography
2 жыл бұрын
@@vanlifesurvivorsguide my heater don't prime that way I hold up and down together on my one
@vanlifesurvivorsguide
2 жыл бұрын
@@Brad_hodge_photography where are you based? is the fuel line soft and green or rigid and translucent? it sounds like you are loosing pressure after the pump somewhere. So either wrong fuel line or a split or crack in the line or a loose connection to the heater or pump and air is getting in
@vanlifesurvivorsguide
2 жыл бұрын
@@Brad_hodge_photography where are you based?
@zummerzetwoodsman1067
2 жыл бұрын
Someone who actually knows what they are on about
@davidschlarp1606
6 ай бұрын
I've got an e-02 and I'm on a 12v battery 🤬🤬🤬
@sukhjinder138
2 жыл бұрын
hello my heater is showing E-3 and shut off after like 5 seconds when i turn it on. its E-3 not E-03 i dnt know if they same or not ..??? please help
@vanlifesurvivorsguide
2 жыл бұрын
Yeah it should be the same, sounds like your glow plug isn't igniting. It could be the glow plug or your battery isn't strong enough to heat it
Пікірлер: 426