Is the racking arm set in the up/down position? Is there enough suction to actually pull liquid through or is it all just going out the bottom dump valve?
@michaelparker4998
4 жыл бұрын
Hi I’m using exactly as you have shown. Works well BUT I am getting entrapment between tank and tri lamp fittings. Run hot caustic 30 minutes then hot rinse. How do you overcome this.
@craftbeertraders7560
4 жыл бұрын
Its always best practice after using a CIP to take all fittings off and spray them down.
@jacksonyandell8825
4 жыл бұрын
I would like to find a barbed “T” exactly like shown in this video, but all I can find are little three-way splices... not heavy-duty at all and ID doesn’t seem big enough. What exactly is the part used in the video for the T? Thanks and cheers!
@jacksonyandell8825
4 жыл бұрын
It seems like a threaded tee fitting (304) with 1/2” mpt to 1/2” barbs inserted at all three ports. Is that correct?
@craftbeertraders7560
4 жыл бұрын
I used one of these www.brewershardware.com/1-2-FPT-TEE.html and 3 of these www.brewershardware.com/1-2-Threaded-Hose-Barb-TFM12B58.html
@jameschappo4202
6 жыл бұрын
Can you please post a complete parts list for this setup?
@MirkoPloch
5 жыл бұрын
I found this PDF with instructions and a parts list from SSBT. This document does not use the racking port and tee though. ssbrewtech.zendesk.com/hc/en-us/article_attachments/115016965366/CIP_MICROsprayBALL.pdf
@zurdzela
6 жыл бұрын
How much liquid do you put in the unitank/fermenter?
@craftbeertraders7560
6 жыл бұрын
We had around 3 gallons in it
@craftbeertraders7560
5 жыл бұрын
I put around 3-4 gallons. Enough for transfer port to pick up liquid while the pump is running. For a 7gal unit it would be less id say probably 2 gallons
@ajoyce
5 жыл бұрын
Does the Micro Spray ball really get the job done? I tried the regular version on my Unitank with a 1/5 hp or chugger pump and it was pretty much worthless. Looking at the micro ball.
@mojonojo3
5 жыл бұрын
Your going to need a bigger pump - i use a 1.5hp job so 7.5x power of the chugger
@craftbeertraders7560
5 жыл бұрын
you need the micro ball when using a standard brewing pump. The regular size ball is for sump pumps and higher volume pumps
@smitty7592
4 жыл бұрын
It will work fine if you do it right. They didn’t explain well on what else you should do.
@smitty7592
4 жыл бұрын
The key is pbw between 130-180 and run it for at least 30 minutes. Make sure the CIP ball doesn’t get clogged. You will hear when it does. Also don’t use too much water. 1-3 gallons is all you need.
@louiscastellanos2691
6 жыл бұрын
so would you do a PBW cycle and then a Star San cycle? Or are you using something else and then rinsing?
@noneyabusinessjack
5 жыл бұрын
Louis Castellanos PBW, fresh water rinse, Acid Cleaner #5, fresh water rinse. Then Saniclean before use. Starsan creates too much foam for use with CIP sprayers in conical.
@craftbeertraders7560
5 жыл бұрын
We do PBW then a hot water rinse. Then well run the no foam starsan. No foam is key
@kevingoetz3158
6 жыл бұрын
Is it possible to CIP the blow off cane?
@craftbeertraders7560
6 жыл бұрын
Yeah you can put the CIP in the blow off cane port
@dennismcwhite3490
5 жыл бұрын
Trying to do this setup. What parts did you use for the Tee?
@craftbeertraders7560
5 жыл бұрын
Its just a NPT T fitting with 3 NPT to 1/2" Barbs
@kaffenons
6 жыл бұрын
What pump are you using?
@craftbeertraders7560
5 жыл бұрын
Its a chugger pump www.stainlessbrewing.com/Chugger-Pump-Center-with-SS-head_p_170.html
@davidbunge9445
5 жыл бұрын
How powerful of a pump are you using for this set up?
@craftbeertraders7560
5 жыл бұрын
Its a standard chugger pump. www.stainlessbrewing.com/Chugger-Pump-Center-with-SS-head_p_170.html
@ajoyce
5 жыл бұрын
@@craftbeertraders7560 The chugger puts out enough PSI for that spray ball? The spay ball says recommended 29 psi I think.
@craftbeertraders7560
5 жыл бұрын
I use the micro spray ball. That one is designed for standard brewing pumps
Пікірлер: 29