Hello, everything is very clear and well explained. I like your CALM VOICE !!! Many thanks! Sorin.
@IvoireTube
4 жыл бұрын
Very good and simple to understand lesson you are a good trainer this is what we need a simplifier . Great thanks .
@jomirife
4 жыл бұрын
thanks
@chips1237
3 жыл бұрын
🙄
@Wintergatan_2
2 жыл бұрын
Very helpful and to the point, thank you!
@user-ef4df7nz5r
7 ай бұрын
Thanks , out of many videos i've watched , this one is the one that worked
@jomirife
6 ай бұрын
at least with this transistor it works
@wilhelmkahn2267
4 жыл бұрын
Very good demonstration - thank you - you are an excellent teacher!
@jomirife
4 жыл бұрын
Thanks. If you are interested in Arduino projects and electronics components, I will publish several videos soon.
@chips1237
3 жыл бұрын
🙄
@Ghostman539
2 жыл бұрын
Thank you for this, it is very useful. I’m a complete newbie to electronics and arduino, but am working on a project that needs to operate a solenoid by a remote control. Is that possible? Many thanks. Mark
@petergesselvan9252
2 жыл бұрын
Very nice. This is what I am needed for my project. Thanks 👍
@jomirife
Жыл бұрын
share the project with me, I would like to see it
@anandsmilesath
2 жыл бұрын
Very useful. Thanks for this video. Getting aspiration to learn Arduino. From where u ordered these products. 1 Arduino, 1 Breadboard, 1 Solenoid (or 1 motor), 6 cables, 1 transistor IRF520, 1 diode 1N4007, 1 resistor of 330 ohm, 1 resistor of 2.2k ohm.
@jomirife
2 жыл бұрын
I have been acquiring the components over the years as I need them for my projects, sometimes I buy other times I recover stuff from electronic waste
@jomirife
2 жыл бұрын
But you can search for kits on amazon or ebay that include all of that
@rizkitrimukti3827
Жыл бұрын
Is that a 5 v solenoid or 12 v selonoid ?
@ibrahimshameed9577
Жыл бұрын
Thanks. Fan from Kerala
@jamespatrickreyes7522
2 жыл бұрын
Hello!! May I know where you bought the solenoid? Thank you and great video
@amireghbal9892
Жыл бұрын
Will this circuit work if you want the opposite effect? I want the solenoid to be in the back position always and pull forwards when needed
@donitamika7018
3 жыл бұрын
I love your projects!!!
@jomirife
3 жыл бұрын
thanks, there are more to come
@TangodownNZ
Жыл бұрын
Please. What diode should I use for a 24 volt 2 amp solenoid? Thank you
@sennabullet
3 жыл бұрын
really nice tutorial. Thank you!!!
@jomirife
3 жыл бұрын
You're very welcome!
@GroovyGamerYT
Жыл бұрын
Does it matter what type of resistor, transistor, and diode you use?
@ibrahimmolero2096
2 жыл бұрын
Excellent tutorial! Is it possible to connect six 5v solenoid with an arduino working all together at the same time? I'm working on a Braille project for donate to blind kids. I hope you can help me. Thanks!
@YouLostTheGame1015
Жыл бұрын
Hey, have you completed this project? I am doing something similar and would appreciate guidance
@bernardomelo169
6 ай бұрын
it helped a lot for my project, thanks
@jomirife
6 ай бұрын
Glad to hear that!
@jeneeflagg8598
6 ай бұрын
well explained
@jomirife
6 ай бұрын
thanks
@jomirife
4 жыл бұрын
Versão em português deste projeto: Circuito para controlar com segurança um Solenoide com um Arduino kzitem.info/news/bejne/uYKCz5-tnWOXiYI
@jomirife
4 жыл бұрын
.
@chips1237
3 жыл бұрын
🙄
@_SHALAKANAGRE
2 жыл бұрын
Thank you, This video was very helpful to me
@lskanon863
3 жыл бұрын
Thank you. Very detailed and well explained.
@chips1237
3 жыл бұрын
🙄
@jomirife
3 жыл бұрын
thanks
@jomirife
3 жыл бұрын
I'm going to publish the complete project where I use this system, so subscribe so you don't miss it 😀
@abuahmedalduhbi9552
4 жыл бұрын
could you do the triggering solenoid for this project with IR sensor?
@jomirife
4 жыл бұрын
It would be easy, but I don't have an IR sensor to do it. But you would have to indicate that when it receives the IR signal, it makes the digital pin HIGH. Soon I will publish a project where I do something similar, but with a PIR sensor. Subscribe to the channel to not miss it.
@chips1237
3 жыл бұрын
🙄
@Orchardman53
3 жыл бұрын
I note you are powering the solenoid via the Arduino power supply (USB). Does the solenoid draw too many Watts on the inrush current for the capability of the USB power? Would a separate power feed to the breadboard and the IRF520 be a more cautious approach? Otherwise a nice clear explanation with good diagrams. Thank you.
@chips1237
3 жыл бұрын
🙄
@jomirife
3 жыл бұрын
yes, you're right, but in my case as the circuit only serves to move one 5V solenoid, I preferred to use the current received by the USB.
@TheMudDragon
2 жыл бұрын
Would it be possible to make the solenoid "pulse" each time you press any keys on a keyboard?
@jomirife
2 жыл бұрын
Yes, you could have a Processing program that whenever it detects a pressed key, it sends a command to the arduino to do something, you could even program to do something different with each key
@pitapotale
Жыл бұрын
Sorry, what is the current and voltage used in the video on the selenoid?
@It.hassss
2 жыл бұрын
That's great demonstration, But if I want to use morethan 1 selenoid, how it could be? Am I just need to adds >1 selenoid, >1 R 330, >1 diode,? Thank you very much,
@jomirife
2 жыл бұрын
do you want to use more than 1 solenoid on the same circuito of that transistor? or control different solenoids with differente transistors?
@jomirife
2 жыл бұрын
note that the arduino only has 5v, you would need an additional power source to power different solenoids at the same time
@It.hassss
2 жыл бұрын
@@jomirife yes, something like that.. It would be not enough, I got that
@nickstamatiou9871
5 ай бұрын
Hi there! Why do you need a resistor with the diode?
@jomirife
5 ай бұрын
the diode can act as a resistor
@Sinasongway
3 жыл бұрын
I like the video. Definitely its wonderful but you could have shown the the components names on the screen when you explained those.
@jomirife
3 жыл бұрын
sure, but I wrote them during the demo and they are on the description of the video
@chips1237
3 жыл бұрын
🙄
@RC-so4ds
Жыл бұрын
Hi, I am trying to reproduce this project but am trying to use a BC517 transistor vs the IRF520, will that work?
@hardikadhyaru8582
3 жыл бұрын
Hi, I want to connect a motion sensor at input and when someone waves, I want the solenoid to operate. Can you help with this ?
@eliasstarr1122
3 жыл бұрын
just use motion sensor, and if input movement is detected set the solenoid to high
@chips1237
3 жыл бұрын
🙄
@jomirife
3 жыл бұрын
I could help, I did this project kzitem.info/news/bejne/r4J_rqJsfaeWoaA where the motion sensor turns on a light, for your project I just needed to put the solenoid pin in that output
@_SHALAKANAGRE
2 жыл бұрын
What is the use of 1N4007 diode in controlling solenoid?
@gigatentaction2356
2 жыл бұрын
Hi, what solenoid are you using? Is it 6v?
@Sunny-pz6zb
3 жыл бұрын
Thank you so much for the video, maybe my project is the different amp of solenoid, so how to calcalaue the resistor and transistor i need? thanks
@jomirife
3 жыл бұрын
you need to check the datasheet of your components to determine which resistors you need to use
@Agility345
2 жыл бұрын
Hello, I want to ask what resistors and transistor do I need, if I want to use 6V solenoid with 9V Jack Arduino connector. Thank you and great video btw =]
@jomirife
2 жыл бұрын
you can use this same circuit, the diode I use is only to prevent the current direction so as not to burn the arduino
@alisameh5085
2 жыл бұрын
I want to use 5v solenoid in a control circuit of an air mattress , should i connect the solenoid directly to the ardunio without a transistor? And does the 5v solenoid even work for such circuit?
@jomirife
2 жыл бұрын
the problem is if you are working with very high voltages
@chadlunders4898
Жыл бұрын
How would you connect 88 solenoids acting independently?
@hamedghaed19
Жыл бұрын
Thank u so much ❤
@abuahmedalduhbi9552
4 жыл бұрын
excellent u r creative
@jomirife
4 жыл бұрын
Thank you.
@chips1237
3 жыл бұрын
🙄
@deonklingbiel
4 жыл бұрын
Very nice. Can you connect 3 x outputs? I have to open en close 3 x motorized ball valved in a certain sequence to open and close water for a solar geyser. Is it possible to do with 3 x outputs?
@jomirife
4 жыл бұрын
Yes, just use a pin on the Arduino for each solenoid. But with this system I wouldn't have enough power por activate all the solenoids at the same time, but I could use them one at a time.
@chips1237
3 жыл бұрын
🙄
@magicianchannel1
3 жыл бұрын
Does it matter how much voltage is used for the solenoid? ; Can i use the same transitor and diode you used for a simular setup using a 9V solenoid? Also, how do you know which is the right mosfet and diode to use in a setup like this? Or are all mosfets and diodes simular enough for a setup like this? Thanks in advance anyone! :)
@jomirife
3 жыл бұрын
Yes, it matter. I tested with the 3V power, and it didn't have enought power to move the piston of the solenoid. So for this solenoid you need at least the 5V. I didn't try yet with voltage above 5V.
@jomirife
3 жыл бұрын
Subscribe for more projets, I will post a bigger project where I use the solenoid to lock and unlock a door using a NFC card.
@chips1237
3 жыл бұрын
🙄
@mitchshivers
2 жыл бұрын
Very helpful! can you show how to connect multiple solenoids using 1 Arduino with a rhythmic pattern?
@jomirife
2 жыл бұрын
i am working on a project with multiple motors, but they are controlled in the same way as a solenoid.
@jomirife
2 жыл бұрын
When it's done, I'll publish the video :)
@mitchshivers
2 жыл бұрын
@@jomirife Theat great! I can't wait to see it all work. I really appreciate what you do!
@gersonfer
4 жыл бұрын
Hello. Very well explained, thank you. In this example, is it a 12V solenoid ?
@jomirife
4 жыл бұрын
thanks
@jomirife
4 жыл бұрын
it's a 5v solenoid, this one kzitem.info/news/bejne/y4KX3Y1prnWQiqw
@jomirife
4 жыл бұрын
Soon I will publish the complete project where I use this part with the solenoid, so you should subscribe to the channel so you don't miss the video 👍👍👍
@chips1237
3 жыл бұрын
🙄
@dr.videos8502
2 жыл бұрын
cna we control the speed of opening though ?
@ashpikachu853
2 жыл бұрын
If i want to run a 24vdc solenoid valve then what are the components do u have to change
@jomirife
2 жыл бұрын
you can use the same, only have to use another power source for that, because the arduino only do 3v and 5v
@Lecandotnet
3 жыл бұрын
Please show component names or number, such as Resistor 1000 ofms, diode 1N4007, transitor Tip120. Thank you.
@jomirife
3 жыл бұрын
that is in the beggining when I have all the components on the table
@NeetipudiSubash
4 жыл бұрын
Sir can a powder like salt flow through this solenoid
@jomirife
4 жыл бұрын
ok
@chips1237
3 жыл бұрын
🙄
@itskay8291
3 жыл бұрын
Sir, i follow ur instruction but only the light on but the solenoid wont move at all. Can you explain why? Thank you sir for your tutorial
@jomirife
3 жыл бұрын
I would need to see your project better to identify the problem.
@jomirife
3 жыл бұрын
Subscribe for more projets, I will post a bigger project where I use the solenoid to lock and unlock a door using with a different setup and connections on the breadboard.
@chips1237
3 жыл бұрын
🙄
@davidlima3615
2 жыл бұрын
very good! How many amps is the solenoid?
@jomirife
2 жыл бұрын
about 1 amp
@jomirife
2 жыл бұрын
it's not a very strong solenoid, it's just for prototyping ideas
@bibil3526
2 жыл бұрын
how much did the project cost?
@jomirife
2 жыл бұрын
just a few dollars, minus the cost of Arduino
@calebjtaylor1
4 жыл бұрын
Hi. Would this work with a solenoid that draws more current, or would I need different resistors etc?
@jomirife
4 жыл бұрын
The arduino can't work with much more powerful solenoids, you would need other components to amplify the power
@jomirife
4 жыл бұрын
Soon I will publish the complete project where I use this part with the solenoid, so you should subscribe to the channel so you don't miss the project 👍👍👍
@chips1237
3 жыл бұрын
🙄
@xmanoel2184x
Жыл бұрын
is it a 12V 1A solenoid?
@stevegoodjob5902
3 жыл бұрын
Can I do this with another kick back suppression circuit where I don't use mosfet?
@jomirife
3 жыл бұрын
I'm going to think about how I can create the circuit without a MOSFET and then create a project like that
@stevegoodjob5902
3 жыл бұрын
@@jomirife thanks 😊 for the reply subbed
@carbon273
3 жыл бұрын
For some reason my solenoid doesnt respond to the low comand on the pin. It retracts due to the power supply but thats it.
@jomirife
3 жыл бұрын
What voltage is your solenoid?
@jomirife
3 жыл бұрын
If the solenoid needs more that 5 volts to work, the Arduino doen't have the power to do it
@carbon273
3 жыл бұрын
@@jomirife I have a solenoid rated for 4.5V minimum to operate. I am using an external DC power supply as well just to draw out the neccessary current. This is the solenoid I am using. www.amazon.com/gp/product/B013DR655A/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 Is this similar to yours?
@kalenmcallister4290
3 жыл бұрын
Does your MOSFET heat sink get really hot when in use?
@jomirife
3 жыл бұрын
In this system.. no, the energy required is very low and does not heat the transistor.
@jomirife
3 жыл бұрын
But this can happen in systems with larger components that require more power. Have you had that problem?
@chips1237
3 жыл бұрын
🙄
@mruscfreddles80
4 жыл бұрын
What about controlling the solenoid speed with a potentiometer?
@jomirife
4 жыл бұрын
You cannot control the speed of this solenoid, you would need another type of motor
@chips1237
3 жыл бұрын
🙄
@LionKing-tx2ve
4 жыл бұрын
Sir,I need the 5v pin of the arduino for another component of the curcuit.... What shall I do in that case? Sir, this is very important for my project...
@jomirife
4 жыл бұрын
I'm not really sure if you can solve that problem, because the 5v to the solenoid is almost not enough to move the solenoide, and sharing that powersource could be a problem.
@jomirife
4 жыл бұрын
Soon I will publish a project where I use many components and sensors in the same system, powered only by the Arduino's 5V, and the power source is shared and distributed on the breadboard. So it can also work that way for you.
@jomirife
4 жыл бұрын
Subscribe for more videos like this 👍👍👍 I will publish more videos with Arduinos and electronics
@LionKing-tx2ve
4 жыл бұрын
Ok Thanks for your assurance Sir...I'll wait...🙂
@jomirife
4 жыл бұрын
@@LionKing-tx2ve I will also post fotos and diagrams of the projet on my instragram instagram.com/jomirife/
@hardcoreprogrammingwarrior7036
3 жыл бұрын
liked and subscribed, nice demo. is this possible if I use Lock-style Solenoid 12VDC ?
@jomirife
3 жыл бұрын
Yes, especially if it is for a door. I used this solenoid on a model for proof of concept because I didn't have a lock type at the time.
@jomirife
3 жыл бұрын
I will post the demonstration of my project maybe next month.
@hardcoreprogrammingwarrior7036
3 жыл бұрын
@@jomirife thanks!
@jomirife
3 жыл бұрын
@@hardcoreprogrammingwarrior7036 you're welcome
@chips1237
3 жыл бұрын
🙄
@elliot1784
4 жыл бұрын
what is the voltage rating of the solenoid/motor u used?.. thanks :)
@jomirife
4 жыл бұрын
5 volts
@jomirife
4 жыл бұрын
Check this post jomirife.blogspot.com/2020/03/solenoid-push-pull.html
@chips1237
3 жыл бұрын
🙄
@elliot1784
3 жыл бұрын
@@chips1237 something above you?
@shaneross9410
4 жыл бұрын
can you make the solenoid move slower and might delay it at open?
@jomirife
4 жыл бұрын
To control the velocity you sould use a stepper motor, mas to delay the action you just do it on the code.
@chips1237
3 жыл бұрын
🙄
@7frendzel
3 жыл бұрын
Can I use 1n4001 instead of 1n4007? Thanks :)
@jomirife
3 жыл бұрын
I'm not completely familiar with 1n4007, but it looks like it
@chips1237
3 жыл бұрын
🙄
@angelicab1136
3 жыл бұрын
how much power does that solenoid needs?
@jomirife
3 жыл бұрын
this is only a 5V solenoid
@nishantscorpio
4 жыл бұрын
Can we simply pull and wait untill I give further commands to push it back
@jomirife
4 жыл бұрын
yes, look at the code, the piston could be pulled while the pin is in "high"
@chips1237
3 жыл бұрын
🙄
@ttv3071
4 жыл бұрын
can we use a tip120 transistor instead of the irf 520
@jomirife
4 жыл бұрын
the tip120 is two NPN transistors, so i think there will be no problem, and will protect the arduino pins in the same way
@jomirife
4 жыл бұрын
Soon I will publish the complete project where I use this part with the solenoid, so you should subscribe to the channel so you don't miss the video 👍👍👍
@chips1237
3 жыл бұрын
🙄
@hugobreu508
3 жыл бұрын
thanks thanks and thanks
@jomirife
3 жыл бұрын
Most welcome
@marwaelries7306
2 жыл бұрын
Can you help me How can i make a solenoid?
@jomirife
2 жыл бұрын
it's possible but it's not easy
@chips1237
3 жыл бұрын
can you burn the arduino or the solenoid?
@jomirife
3 жыл бұрын
the Arduino is more sensitive to electricity
@islamckie9317
3 жыл бұрын
love it
@jomirife
3 жыл бұрын
i love it too
@HaidenMcGrath
Жыл бұрын
Why not use a relay?
@citratunealt1
11 ай бұрын
Relays are inferior to mosfets.
@aliagandara9366
2 жыл бұрын
i need to do that
@jomirife
2 жыл бұрын
have fun
@casssimpeer9118
3 жыл бұрын
Can you control Six Solenoids with one Arduino
@jomirife
3 жыл бұрын
as long as you have anough pins for that, you can. But sendind power for all of then at the same time, can be a problem.
@jomirife
3 жыл бұрын
thanks for the idea, i will try that, and give you credit
Пікірлер: 198