So is the 398v that you getting is good or does it have to be the exact 400v
@jamesfiskwslsproductions5528
8 жыл бұрын
Awesome Video we are working on them tomorrow.. we will send you some vids and stills of what we find
@popeguitar
8 жыл бұрын
+James Fisk perfect! glad I could help!
@surby7400
6 жыл бұрын
Im having an issue with my sharpy. Another tech had tried to repair it and failed, so im left to clean up his mess. Volts are good across the boards. Only thing that happens when i power the fixuture is a slight click and then just faint beeping. No fans or anything. Only thing i noticed was the control cable had the blue pylled out of the plug.
@antoniohurtado6742
5 жыл бұрын
You could guide me on where the 5v go to activate the ballast outside the mobile head
@granjavis
4 жыл бұрын
I have a trouble with the 5R sharpy , works OK from the beggining , Also turns on the lamp by DMX command but when fixture returns from sleep by receiving DMX it's impossible strikes on the lamp without recconecting AC mains , everything else works just fine. Recomendations ?????
@veyselery6729
5 жыл бұрын
hello I have a question I would appreciate if you help I have a problem with sharpy jihad ballasttan doing all the voltages, but the bulb does not fire with a solid ignitor I try again with the same result what should I look for thanks
@sahoo738
6 жыл бұрын
Sir 10R yodn ball price
@justiceaguirre
Жыл бұрын
hey allain I have 2 beam 230 i only use them one time! now they don't turn on or anything I changed the fuse and every time I turn them on the fuse burn! what could it be? thank you in advance
@DjNissimNYC
3 жыл бұрын
Thanks ! I have an alpha spot 800 with an error saying comm ballast error and sometime ballast init error.. everything looks fine.. It fell off a chair nothing crazy and since it’s been giving me this error and not turning the lamp on
@DjNissimNYC
3 жыл бұрын
How do I fix it?!
@dersonsalles
8 ай бұрын
qual a voltagem para iniciar a lâmpada?
@deejaykarthikofficial1178
3 жыл бұрын
Same problem plz help me sir
@sahoo738
6 жыл бұрын
10R ingeneater yodn price
@shockedproductions1572
7 жыл бұрын
Should the power supply be outputting 400V continuously, or does it one output the 400v once you send the strike command? I've got one where I can't get a 400v reading anywhere on the power supply. I've swapped the PSU and the ballast from another working light, and still can't get any reading from the PSU. Could it be that the ballast isn't getting a strike command, therefore it's not telling the PSU to send it voltage? I am not getting any kind of errors on the fixture either. I've also tried swapping the control cable, and the cable from the PSU to the ballast, neither one of these did anything. Also checked continuity on the lamp on sensor, and it is working. Next step I am thinking is swapping the logic board, other than that I can't think of anything. Any ideas?
@popeguitar
7 жыл бұрын
Yes the PSU should be outputting 400V all the time... If you tried swapping it with a unit that you know is good from another fixture and you still don't have the 400V, try to disconnect the 28vdc output on the PSU to see if the 400V comes back.In a lot of cases if another pcb or motor driver is shorted somewhere in the fixture it can bring the PSU to ground and make it look like it is not working... If you unplug the 28vdc and the 400v comes back it means there is something wrong elsewhere in the fixture...Good luck
@Savagetechie
6 жыл бұрын
theres also a verticle fuse wrapped in heatshrink next to the 400Volt output.
@lightjockey0000
7 жыл бұрын
Could you help me sir for what is the meaning of "Mt board conection fail " apears on my beam 280 screen Which part is called mt board
@popeguitar
7 жыл бұрын
Jockey Light I'm guessing it's a Chinese fixture?...it's hard to tell without the user manual... I suggest you look for bad connections on the main control card and all the other cards in the fixture... And usually there is a control cable on the Lamp Driver (ballast), very small connector with tiny wires..maybe a bad connection there... My guess is that the main control card doesn't see another pcb or component in the fixture
@Toiladuy249
5 жыл бұрын
beam 230 does not receive DMX port. tested board dmx not damaged. Please show me how to fix it. thank you
@granjavis
4 жыл бұрын
did you follow the signal from dmx conector to the tranceiver chip ?
@dagrind69
3 жыл бұрын
Hey my head is restarting when it’s connected to controller and I move channel
@rosariotrovato4947
Жыл бұрын
ok tank s
@romariano71
5 жыл бұрын
if it has power but without light(not blown out) then it will be ballast.. 25-45dollar online..
@felixehrig3708
6 жыл бұрын
Hey, i've got. ohne question: my Beam 5r Head powers ob the lamp, but After about 30 minutes the lamp turns off again. If you then wait untill it has cooled down again, the lamp will turn on again if you egnite it. What could be the Problem here? Thanks for your help
@jaimeozuna5627
5 жыл бұрын
felix ehrig hey u need channge lamp replace
@brian-ikg217
5 жыл бұрын
The fan that cools the lamp doesnt work... the one that is on the side of it
@pedroborges5203
5 жыл бұрын
Good afternoon, I bought a new lamp for my moving head to think that it was from the lamp that did not light.With this lamp lights but the light that gives is weak.Can it be of ignitor or ballast ? Ignitor link imgur.com/a/3QmXcTZ ballast link imgur.com/a/zAjw20j Does anyone know how to test these components with the multimeter?
Пікірлер: 30