Thank you for the video. Im impressed. you were right. We had cleaned the battery terminals recently but tonight -all of a sudden the car just clicked -it wouldn't start.Everybody said my starter was going out. I wasn't convinced then I watched this video and so I cleaned and cut and stripped down to clean wire on the positive wire and it fixed. Ive started it 5 times and drove and started it again.
@doxland
8 жыл бұрын
Your stuff is a pleasure to watch. No BS or excessive Hubris. Not afraid to stick to your engineering principles. Just speak the truth. Thanks
@dhyde9207
9 жыл бұрын
Just wanted to say how very much I appreciate the effort and skills you put into these videos. I found the channel a couple of weeks ago and have been amazed at how much I've learned even well into my 7th decade on this old earth. Thank you Brian.
@DEATHPALOOZA
6 жыл бұрын
My negative wire is smokeing when i jump it
@dmsfour
10 жыл бұрын
Hi Brian. I really enjoy your videos. I was going to leave a comment on how you really should do what I do with my own vehicles - (Replace wires, Solder Terminals, Shrink Wrap, Silicon Dialectric Grease, Etc.....). But then I changed my mind on that comment for two reasons: First, What you showed is about what any person could do themselves to get the job done - no fancy tools, parts, or special skills needed! Second, If someone who just uses their older car as basic transportation was paying you to get it going - you probably saved them 1/2 hour of labor cost, etc.. by not doing (likely) unnecessary stuff. Again, thanks for putting these videos up.
@DJScopeSOFM
8 жыл бұрын
Quickest 16 minute tip I've seen!
@damianmcdowell5550
Жыл бұрын
I bought a new starter motor. 400 bucks almost in U.K. money. Fitted myself (not difficult even for a rank amateur). Still got the same rapid sequence of clicks - arghhhhhhhhhh !!! Found your video, cleaned the terminals…… bingo!! Nice one Brian. Cheers pal. Damian England
@wdlnds08
6 жыл бұрын
Hey Brian, I just spent past 3.5 hours getting my car to the house from work. AAA battery guy then tow trucks. first guy tested and said battery good alternator bad, second guy said bad starter and both spent a bit of time testing and diagnosing. Finally get it home and started pricing starters and alternators and estimates to fix. Came across your video and thought what the hell let me check for corrosion and connection. post terminals felt good but then I start checking the ground that is secured fixed to the post underclip and damn if its not loose. snugged it up tight and Bam it started right up!!! Thought I was dreaming! Thanks for leading me to it! Now what to do with all this extra money since no repair!!! I was looking at potentially getting taken for $600+ as the starter is under the intake manifold middle of the block. Can't thank you enough!
@majorhealey3194
8 жыл бұрын
Intelligent & informative. You're the type of person I love talking with because you're smart. Great video dude.
@applepiebetty
8 жыл бұрын
Little more impressive to hear you show what it sounded like before you started, and that it did fix it. BUT... Love your full job on it. I just went out to my car and had this problem, and figured it was the cable, but din't know to look for the bulging and cleaner copper (which makes sense) so thank you so much!
@cassandrafendi5418
9 жыл бұрын
BRIAN thanks so much!!!! I kept telling the dealer at bmw that I noticed my car wouldn't turn on when it was a very hot day! They kept giving me my car back saying I had no codes/ no faults. But I insisted that something was wrong with my vehicle. Such a shame they didn't know this And this is why!!! The cooling sensor!!!! Great work Brian thankssssss! I'm gunna go buy the part in the morning 😛
@faithpaintandberries3120
4 жыл бұрын
As a lady I am impressed lol. I just had my car towed 182 miles. I wish I watched this before I sent it. I could have checked this first. But I’ll definitely check it once I get back
@markrivera4911
8 жыл бұрын
Hey Brother! I just impressed the Mrs!!! Getting some love tonight!!
@briansmobile1
6 жыл бұрын
Heck ya Mark!
@spencermccormick7781
9 жыл бұрын
Electrician's tip: when send two wires into onto contact take some pliers and twist the wire tips together for better contact.
@Glenn7719
5 жыл бұрын
My instant thought was starter motor so as i had one laying around spare i thought id change it, few days later it was doing it again. As ive got aftermarket battery terminals i took them apart, cleaned the wires and connections, there was no visible signs of corrosion or anything, maybe just loose in the connections, put them back on nice and snugly and it fired straight up. That was yesterday and had a few starts and no problems, so far so good. Cheers for the vid.
@robert5726
4 жыл бұрын
Thanks! I could not fix my dreaded clack, clack, clack. I kept trying to clean my clamp to battery connection until I watched your video, so I took apart the clamp to cable connection, cleaned it up, and she fired right up! Yahoo!
@14demonhunter
9 жыл бұрын
My '05 Accord had these issues about a year and a half after i got it. it got so bad that the car decided to shut down completely while I was going 70 on the highway.
@irishawn5856
6 жыл бұрын
Thank you x 1 million. You saved me a towing bill and service call. My Hyundai Tucson battery terminal had a metal cap with a stud that was rusty and under that metal cap had rusted a little bit. Clean them up and vrooom. Lol. All good now.
@BillSikes.
5 жыл бұрын
Good tutorial but would of been even better if you'd demonstrated the noise it was making before you repaired it, those clicks are caused by a variety of different reasons
@notafuckinpplperson8233
5 жыл бұрын
strake750 he did his machine gun sound effect lol
@mrobvious5892
3 жыл бұрын
@strake 750 What are some of the reasons for those clicks?
@dolssondko
10 жыл бұрын
Brian, once again - another awesome video. You and Eric The Car Guy have such a great way of delivering solid, helpful, and easy to understand material. Without an ego issue. Love it!
@thestrangeceleb
3 жыл бұрын
2021, and your video is still helping people. thanks man!
@leopsa
8 жыл бұрын
great video 1 P.S. never blow the dust off a battery you could blow dry acid dust back in your face please be careful keep the vids comming
@RangerCaptain11A
4 жыл бұрын
that corrosion is either lead or copper sulfate, and dried battery acid. same stuff on pennies.
@jarinwilson9539
10 жыл бұрын
Terminal voltage drop would have easily confirmed that those battery connections where garbage. Also, if you feel excessive amounts of heat(so hot you can't touch the cables or a non contacting pyrometer shows large amounts of heat) chances are the cables or/and their connects are faulty. The swelling of the cables, brilliant little tip their Brian and yet another awesome video.
@flywiththe7471
10 жыл бұрын
Old trick I learned in school about cleanly stripping copper wire, Is to use a lighter and just slightly melt the tip. Doesn't work too well on heavier gauge wire. But works awesome on smaller wires.
@briansmobile1
10 жыл бұрын
Great tip- I'll try it out!
@BrianBuehler
10 жыл бұрын
Nice to see you explain why the negative cable is removed first! Another mechanic on here did something battery related a while back and told people that this step was not necessary. Sadly, I was chastised for mentioning it :-(
@user-cz4jk4yz9q
Жыл бұрын
Thank you for posting this video! I absolutely love how you explained and showed with just the right amount of detail! Explaining the whys of things too is helpful. Please post more videos like this for us females that don’t like to get taken to the bank every time we have an issue that could be an easy enough fix if your willing to get your hands dirty 😉 So thank you again. I’ve never sent a message on any video I’ve watched but felt compelled to tell you it was very helpful. Maybe I’ll impress a man someday with these skills…. Or, you never know, I may end impressing the ladies as you stated 😋
@jondoe5482
8 жыл бұрын
Those little felt washers actually are relatively practical, because they prevent a corrosion trail across the terminals that results in slow discharge of the battery. And the red/black colors make it easy for anyone to identify the + and - terminals. Not a bad invesment for 50 cents.
@OCBircher
8 жыл бұрын
Great video,thanks for going step by step, and not just saying, "Now get the cables ready..." and having the video jum straight to the unscrewed and stripped cables like so many videos do. Get a GoPro on a head band, or somebody to be your second camera, for the few times you have to block the action and move in front of the camera, then it could be it's own show on tv.
@gabeskipper1574
10 жыл бұрын
Great Vid. Its amazing how often I find corrision on the positive cable or a loose ground to be the root problem. I think everyone should have one of those battery kits you put together.
@jra19741
9 жыл бұрын
Brian, I have a 91 miata that won't turn over no clicking no start. I replaced the battery, starter and still nothing. Any advise would be awsome. Hope to hear back from you soon. Thanks.
@SirAndrewII
4 жыл бұрын
Don't know if this will fix my car but you've certainly helped give me information and now I have something to do while my car sits dead in the driveway.
@HeroSosh
6 жыл бұрын
gotta say, thx a lot for putting this out there. its a wonderful thing about the internet, to be able to diagnose and potentially troubleshoot and correct an issue before having to shell out hundreds of $$$ to fix something. Im thinking that this is directly more of the issue w/ my car now.. before I was seeing videos directing me towards either a bad fuel-pump relay or this. and again, really thankful for honest, helpful people like urself taking the time to put honest, helpful info out
@seeya205
10 жыл бұрын
I am always amazed when I see people's batteries! It just takes ten minutes every fall to clean them and put some "red junk" on it and you will never have a problem!
@trecker59
8 жыл бұрын
HI BRIAN. RE VICE GRIPS~ MANY YEARS AGO I HAD AN OLD MORRIS OXFORD, THE HAND BRAKE HAD TO BE ADJUSTED NEAR THE DIFF UNDER THE CAR. AFTER DOING THIS I COULD NOT FIND MY VICE GRIPS ANYWHERE, ONE YEAR LATER I WENT UNDER MY CAR TO ADJUST THE HAND BRAKE AND THERE WHERE THE GRIPS A LITTLE RUSTY BUT STILL CLINGING ON. THANKS FOR THE VIDS PETE.
@maryperkins202
8 жыл бұрын
thank you, great video and just the diagnosis I was looking for.
@briansmobile1
8 жыл бұрын
You're welcome Mary! Thanks for clicking like and subscribe!
@maryperkins202
8 жыл бұрын
Hey thank you again. This actually wasn't my problem but after changing them there was little else to do. I recently "reconditioned" (poured out the battery acid and inserted a epson salt water mixture) into my battery, I trickled charged (2amps for 12 volts) it for about a week while driving. It ran great after that then about a month later it would just click. My battery was still fully charged trickle cell style but completely dead at (6amps for 12 volts). I put it on the charger for that and it started up. Not sure what any of this means, just wanted to share because I couldn't find any types of remedies or problems like this on the internet.
@tylergross2672
7 жыл бұрын
Mary Perkin
@abear2302
7 жыл бұрын
excellent video , thank you , saved me a fortune in garage bills . down to earth advice. cheers
@ReclusiveMountainMan
10 жыл бұрын
It's nice to see people doing the job right. Thanks for the instructional video. Keep doing what you do. I appreciate it.
@SuperPetrolhead87
10 жыл бұрын
very good info brian!ive had issues where people lube the battery terminals so much that the lube creates a circuit....and shorted!keep em coming!
@kirawilson7054
7 жыл бұрын
It would be helpful if you could provide a list of everything in this toolbox!
@LoveClassicMusic0205
7 жыл бұрын
The one thing I wish you had done differently was to color code the terminal so the positive terminal could be identified at a glance. I'm actually surprised that the cables themselves weren't already red. Other than that, great job.
@alcyr5655
7 жыл бұрын
Great video, and a good reminder, most electrical problems are caused by poor battery supply, or corroded grounds. I really like those crimp on connectors, I'll have to see what auto parts store carries them. That is a much better way then trying to stuff all three wires into the clamp of the battery terminal. They always tend to compress, and then make poor contact. Where do you get your crimped on connectors.
@ivanbgct
10 жыл бұрын
Where do you buy the solder-less connectors from?
@jamesvannihj9099
6 жыл бұрын
Very informational. Introduced more information than I was looking for to solve the issue I am currently having with my 2007 Honda (Jan'18). Love the sexy comment and sound bit.
@raoulduke6464
8 жыл бұрын
03 sentra. Fixed. Thanks for saving me some $ dude!
@sandraevans6905
8 жыл бұрын
So glad I found your video..One cable was corroded put wd40 on it. Still nothing but will take the terminal off next. Keeping my fingers crossed.
@CodyJv
10 жыл бұрын
I'd use solder on tips or at least tin the wire after crimping then put some black liquid electrical tape dapped in the areas of corrosion. Will be the best method to never have to deal with this again.
@MrKingNica
9 жыл бұрын
Great video dude. Ain't nobody got time for that was too funny, lol.
@JonBurnsArt
9 жыл бұрын
I thought I needed a new alternator. I saw the posts on the battery were so corroded that the negative copper was snapped on the lower band. After cleaning it with baking soda, the car did the rapid clicking. I had to jump it and after 10 minutes the car died. I think I need to replace the post attachments. Thanks for this video. I just happened to see it on a follow up vid. :-D I was ready to replace the battery and alternator. Save me $$
@stevejones8486
8 жыл бұрын
Ron Paul poster in the background...
@joekerr1763
8 жыл бұрын
TRUTH
@michaelheise6294
6 жыл бұрын
End The Fed!
@samjohnson466
10 жыл бұрын
I left the engine to chassis cable off on a rebuild once, slow crank, no start, and a small wire from the engine to cabin would smoke. That jumper is important because motor mounts are made of non-conductive materials.
@dwayneshields7995
8 жыл бұрын
my first car doing the same thing. i got a 98 mustang for a first car and begore it worked but now it made that noise when it started. thanks to u i can fix it no problem. thought my engine was jammed or somethin.
@LJRossPhoto
10 жыл бұрын
I always rub a thin layer of dielectric grease over all the metal to metal connections. I've NEVER even had a hint of corrosion, nor have I ever had an electrical issue/failure.
@annapinky361gorgo9
8 жыл бұрын
Brian! I need you to start the vehicle please! I was ready to take on a rescue and then said to myself, ummm what if it doesn't work? Great video though. Thanks! 😊
@1983ufgator
9 жыл бұрын
Hey Brian, My memory sucks! The other stuff recommended by one of the people who commented here was 'New Skin' not liquid hands and their name is binnsh not binner. Wasn't even close on the name of the product. Sorry about that.
@AnagramForCraig
10 жыл бұрын
Always educational. Always entertaining.
@1983ufgator
9 жыл бұрын
Hey Brian, Just discovered you and this video. Great stuff. I live in an old house with cast iron radiators and my hands get so dry they feel like they're going to fall off. I renovate houses and work with my hands a lot too, so it's vital not to let them get that way. Somebody named 'binner' recommended 'liquid hands' for when your skin has already cracked. I have to try that too. But the stuff I really like... so they don't get to that point (though sometimes they do if I forget to put it on) is called 'Working Hands' by O'Keefe's, I get it at Home Depot where it seems like I live 24/7. It's great stuff, not greasy and if I use it a lot, my hands don't crack. Hope this helps and thanks for the great video. I'm going to subscribe to your channel this very minute.
@Finnigan9
10 жыл бұрын
Did you ever destroy a battery post? U can do that with channel locks if the terminal is too tight. I'm sure you know that but it would be good to warn people that such a thing can be done. THANK YOU for posting the great vids. You are great at filming and explaining everything you do!
@briansmobile1
10 жыл бұрын
Way back in the day I was working at Autozone and swapped a customer battery that was so badly sulfated internally and corroded externally that the post came up out of the battery. There was no fire, but ya, it happens.
@tsr7198
10 жыл бұрын
Nice tip. Whackety Shmackety! Cracks on dry hands equals Super Glue don't you know? Love this channel.
@FireEater
10 жыл бұрын
Good stuff.you scotty and Eric,best auto repair videos on KZitem.Tks
@JBSmoothShaft
7 жыл бұрын
No start? I WATCHED THIS WHOLE THING FOR NO START!!!! I'm a millineal got damn it!!!! I'm titled for fuckin pleasure at the end of everything I do. Got damn you maaan!!!
@lasdiLP
5 жыл бұрын
Not trying to be rude, but it would be helpful if you would actually test the car after you've "fixed" the problem. Also, please stop putting so many ads in your video.
@Oberyn_Martell
9 жыл бұрын
You saved me soo much time. Thanks for the upload. Thumbs up.
@Tacticalcatninja
8 жыл бұрын
you save my life i bought my first car used drove it home and it wouldt start knew it had something to do with the cables but wasnt quite sure
@briansmobile1
8 жыл бұрын
+Omar Reyna You're welcome! Thanks for subscribing and hitting the like button!
@binnsh
10 жыл бұрын
Try "New Skin" from the drugstore for cracks on hands, a paint on bandage in a little bottle.
@TheHaydn14
9 жыл бұрын
briansmobile1 Could an alternator be causing the rapid clicking also? Or would it more commonly be a faulty battery or bad connection at the terminals? Cheers mate
@katzkatcher
8 жыл бұрын
Couple of tips for ya . When you change your oil drizzle a little left over oil on your battery terminals .Corrosion doesn't grow well in an oily environment As for the cracks in your fingers, I use super glue on mine .
@322doug
6 жыл бұрын
as battery gets weaker does the clicking slow down..... second , is it a relay clicking
@rickievadas6131
4 жыл бұрын
Thank you so much for your time to post this video...im running out to try this right now...my Z24 has been broken 2 months..this maybe a stupid question ...would anything be different if the battery was side post. Again thank you so much...ill let you know.. God Bless
@manwiles
Жыл бұрын
Great job and video. Learned something to help save me money.
@prestochange0
6 жыл бұрын
Yo you saved my trip to the garage bro thanks! Very well done homie ! Cheers!
@josephsotelo8032
9 жыл бұрын
Hey brian i have a question i have a 1997 eclipse 420a engine it wont start just make a click sound my starter relay its located behind my radio that's where i hera the clicking noise then i leave the car alone for a couple minutes and the car will start again, do you know what it would be. Thanks
@antons2975
Жыл бұрын
You saved my girlfriend and I 250$ 70 for parking ticket, 100 for labor , and 70 for a starter. I took her nail file and filed the terminals and connectors. Tomorrow we’re going to get new terminals. Tomorrow is street cleaning and we would have gotten a ticket.I thought clicking was the starter so we were planning to get a starter.
@marleyrobertson6417
6 жыл бұрын
Thanks Man.. Kinda Wondered why my connector wasnt hittin.. WOW Im Amazed
@aokay7
10 жыл бұрын
My negative battery terminal doesn't seem to tighten so sometimes when I go to start it the negative terminal has popped off from driving and hitting bumps in the road. I'll probably end up doing something like this, thanks for the great video
@yoancarlove7383
10 жыл бұрын
''Vice grips: you can open a hood with them...'' lol True story
@MyStonerMind420
10 жыл бұрын
After market or higher performance audio batteries often have terminals that are in different positions, how would one go about extending the existing power cables?!
@zane7105
8 жыл бұрын
hi i have a 87 bronco 2 it has 40 psi fuel pressure and spark it starts then quickly dies ive replaced the spark plugs,sparkplug wires distribitor cap,fuel filter but still nothing. in warm weather it will run if i pump the throttle constenley but very badly. what should i do? thanks
@SushiPac
10 жыл бұрын
Great video Brian. I'm going to send this to my Automotive teacher. We are doing no start concerns at the moment at school
@seadog19591
9 жыл бұрын
good video, good thing the customers aren't looking for anestetics, they'ed have to go to the hospital for that
@iamshe_destiny996
5 жыл бұрын
Hi Brian my car is making that loud clicking noise but it’s starting just can’t drive. Also the oil light and battery light comes up on the dashboard. It just shut off while I was driving and clicking started when I would try to drive.
@bifftannen8505
8 жыл бұрын
Thank you foe the comprehensive video. I have a 2000 jeep laredo with the electrical problem no one can solve (guages go crazy, sentry light stays on). I found that if I take the negative cable off for 15 minutes, it keeps the problem away for several weeks. So I take the negative cable on and off a lot over the last few years. But now the negative cable is worn and I've got the fast clicking until I move the negative cable around, then it will stop clicking and start. My negative terminal I'm sure needs replacing. when you did the cable, does it matter which cables go on the right or left end of the new terminal? I'm assuming it doesn't matter, but just want to make sure beforehand.
@BLAZE5417
9 жыл бұрын
Thanks Brian for your video on how to replace the ends on the battery cables. None of my vehicles cables ever needed to be replaced, "until now"! My dads had me working on cars and with power tools since I was 11 so this isn't nothing thanks so much again for your video. Hey I like the red beard, as a redhead I can't help but not to. I know you originally posted this at the beginning of the year and now we're back into December of 2014 so you and yours have a nice & Blessed Merry Christmas and Happy New Year Always, LadyRed
@deserteagle1039
6 жыл бұрын
Thanks bro got my car running again thanks to the video
@shueher1
10 жыл бұрын
Have a no start problem with my 1998 v6 Honda accord. The terminal on the + and - was pretty corroded due to battery leak. But before that the car would crank but would not turn over. So I try switching the gear to neutral to start and it didn't work either. Then I put it back in Park and now the car doesnt crank but would click. Tried a new battery and it would click only. The light on D4 would light up too when trying to start it. Thinking it might be a neutral safety switch? Had a P0706 code too.
@pegriz4126
9 жыл бұрын
Awesome! Thanks so much. I posted to FB with the follow message: 02 Toyota Sequoia would not start- clicking sound. Lights and power worked fine-so battery fine- in terms of charge. Thinking starter issue, and planned to get towed into shop. I found this, and sure enough just a little corrosion was the issue. Did not snip wires or replace connectors yet. This video saved me time and $. So in case you have similar issue take a look. I Cleaned terminals/ connections and bam problem solved, need to change + wire as you showed, but appears my wires are too short. Need to figure out how to put new wire in to fuse box. Got a video on that? THANK YOU!
@thaliasoma
9 жыл бұрын
Same here, thought I'd have to change the spark plug, but I'm sure it's a battery issue now. So much easier to deal with. Phew!
@jeffbosio9318
8 жыл бұрын
What did the car sound like before you repaired it? My 2001 Nissan Maxima has a working battery and the starter seems to be working. I hear several loud clicks which sounds to me like the starter engine trying to work. I have turned the crank shaft and was able to turn it a few rotations, so I don't think it is my engine seized up. When I get home I'll take a closer look at the cables. The terminals aren't corroded, but I didn't look too closely at the wires.
@briansmobile1
8 жыл бұрын
+Jeff Bosio It just clicked rapidly and fast. Thanks for subscribing and clicking that thumbs up!
@340rps
2 жыл бұрын
Always, Always check the battery first. Chapter 1, page 1
@DJDevon3
10 жыл бұрын
20 minute quick tip :P I know editing can be a pain in the butt but you could improve your videos with it. Learned a lot as always. Keep em coming.
@joemilner2055
10 жыл бұрын
For an even better job, you need a good pair of crimpers. It would save you time and do a better job. I also use the self sealing heat shrink and heat gun. There is no way battery acid can get into those. I also replaced the terminal posts on my 2001 Dodge diesel with the Mil-spec posts found on eBay.
@barbwirepupp
9 жыл бұрын
Thanks, took your advice, had a low battery. Won't forget the light trick.
@Oldtimecarpenter
9 жыл бұрын
Thank you thank you!!!!! Great video and good sense of humor!! I've subscribed!!! 😜
@knunne1
10 жыл бұрын
Love those cable cutters, they cut cable like butter.
@theotherside7634
4 жыл бұрын
Super Glue for the cracks in your hands/fingers I have the same issue in the winter, a friend suggested it and it works perfect.
@neowulf
8 жыл бұрын
Great video- learned a lot. Just a suggestion- closer camera on crimping. Thanks.
@rafitarodriguez9781
7 жыл бұрын
I have a 3rd Gen Camaro and my car wouldn't start it's click fast so I went home (12:05 at night) the next morning I went to tow the truck I showed them that the car would only click but it didn't click or anything it stayed quiet could it still be the cables??
@jvaldez8649
8 жыл бұрын
Dude, you need to start it at the end.
@karelvanderwalt3625
4 жыл бұрын
crank for closure
@Archifx
10 жыл бұрын
Not a bad job. It's amazing how even the lightest corrosion can make electrical problems in any car.
@ricobangz8638
7 жыл бұрын
Hey man, I have a big problem. My father was driving his 99 Ford Taurus to work, it just lost power and wouldn't start. When we went to go pick him up and look at it we noticed the positive terminal was actually snapped. It was still on it, but it had broken and was loose. So we went and got new terminals, and when we went to jump it the firewall ground strap started smoming fairly bad. We thought we might have shorted out a wire or somewhere it got crossed. So we went ahead and changed the battery and ran new ground to the chasis and positive to the solenoid to no avail. It would click a couple of times then nothing. Checked relays but they were fine. I cleaned off all connections in from of the engine bay. Would the ground strap itself be a problem or do you think it is something else? Btw it is a 1999 Ford Taurus 24v DOHC.
@Uncleorangesoda
10 жыл бұрын
That negative battery cable is actually how it comes from the factory. From the battery straight to that bolt only one cable.
@fangorn1000
9 жыл бұрын
After spending more than $ 500 to have my car started. It was a fuse after all. So folks try the easy things first before you spend hundreds of dollars.
@jerryuuc
5 жыл бұрын
I HAD THIS SAME PROBLEM....TOOK IT IN THEY SAID IT WAS THE STARTER SOLINOID ....AND THEY HAD TO CHANGE THE WHOLE STARTER WITH THE NEW SOLINOID ON IT......STARTED FINE WITH THE NEW STARTER......BUT DID I REALLY NEED A NEW STARTER?....THE CAR WOULD START...JUST RAPID CLICKING SOMETIME......COST A LOT FOR NEW STARTER AND INSTALLATION MAYBE THEY JUST FIXED A WIRING PROBLEM....YA I'M GOING BACK THERE FOR MY STARTER WARANTEE!
@helenamcclary4079
6 жыл бұрын
Hey brains I have a 2012 Hyundai sonata and my positive battery post is loose I tried placing a battery post shim in between the battery post and the cable and my car still acts as it doesn't want to start I saw that you crafted a new on this car which is a Honda so my question is can I do the same to my Hyundai sonata if so can you make a video instructing how I can do this.
Пікірлер: 336