Thank you for posting this... My 2013 Australian delivered Nissan X-Trail with the Renault 6 Speed Gearbox has this setup also... It worked a treat.
@anarasii
Жыл бұрын
👌👌👍
@stevefournier1901
4 жыл бұрын
Thank you, I was trying to figure out how to use that bleed whole. Much appreciated.
@signummotors
2 жыл бұрын
Normally I'd say it'd be better to bleed it into an empty bottle and add fresh fluid - but for the ease of it and speed of bleeding the clutch - I'd say it's a good way to bleed, since the end of the pipe is in the reservoir, you don't get any air coming back, only fluid if anything. After it's done you can always just replace part of the fluid in the master cylinder tank anyway, so definitely useful stuff.
@niallcosgrove
Жыл бұрын
Thanks for posting this. Worked a treat on our Nissan Tiida 2007. Its not identical but works on the same principle
@maxwellkaan
3 жыл бұрын
Thanks for the great video and clear explanation, much appreciated
@anarasii
3 жыл бұрын
Any time 🙏
@ademirlima5788
4 жыл бұрын
Obrigado por compartilhar, tinha dúvidas sobre o procedimento.
@davedangerous
Жыл бұрын
The clip and connector likes to stick. I lubricated Nissan Tiida 2008 with spray lubricant and it loosed up. The clip pushes down while you pull the connector sideways. I did the same thing with my Nissan Almera 2013 clutch and the connector pulled completely out and dropped the entire master cylinder brake fluid on the ground. The clip does completely different things on different models. The almera clip is totally sheit to say the least.
@extasynord
2 жыл бұрын
tank you, very nice explained
@FASTU-mz3tm
Жыл бұрын
yeah thas about it, only thing i do diferent is not blead it into the brake reservoir, so it dont contaminate the brake fluid on the brake system......................................
@ruubguus4321
3 жыл бұрын
From 🇲🇽 gracias!!!!,👍
@leonardofelix4104
3 жыл бұрын
Muito obrigado salvou parabéns pra vvcs
@fucel91
Ай бұрын
Dziękuję za uratowanie życia!!! Pozdrawiam z Polski ❤❤❤
@laserr10000000
3 жыл бұрын
Thanks a lot
@AzizAllam
4 жыл бұрын
Thanks for the video Aziz
@anarasii
4 жыл бұрын
Mar7ba khoya
@AzizAllam
4 жыл бұрын
Shokran video help me fix my car
@jessezass
3 жыл бұрын
Cool, thank you very much. I was looking at the procedure on AllData and about to have an anurism.🤬
@anarasii
3 жыл бұрын
🙏
@MohamedAlnaas-zd1tg
8 ай бұрын
Thank You!
@arturdoko9011
5 жыл бұрын
Hi o my scenic2 is problem ,what to do??
@cultusgti
2 жыл бұрын
Thank you
@anarasii
2 жыл бұрын
🙏
@mirjunior9864
6 ай бұрын
Well explained, useful video. Especially the trick how to press the metal pin in order to open the bleeder. I knew how to do it but I couldn't open it. After watching this the cluch fluid is replaced in minutes. Many thanks!
@anarasii
6 ай бұрын
Any time 🙏
@MRTuning704
2 жыл бұрын
My cluch peddle went to the floor and I went to install a new master and bleed it and noticed I’m missing the clip 😭
@mistrybipinkumar5272
2 жыл бұрын
Meri duster m kabhi bhi clutch kaam krna bilkul bnd kr deta h to kya kre??
@bmwm5bmw610
Жыл бұрын
Why you bleed it did you just replace the slave cylinder that's why ??? My slave cylinder is leaking inside gearbox what should do is there any chance of stop this leak 🤔 thanks
@anarasii
Жыл бұрын
Hi no the only way is to replace it
@bmwm5bmw610
Жыл бұрын
@A&N Vlog ok ...thank you
@AmrikSingh-mm4cs
3 жыл бұрын
Esy chang kaisy kry
@anarasii
3 жыл бұрын
🤔
@simrankabli5023
3 жыл бұрын
When I put in the second position it doesn't lock, because after the bleeding there pressure on the clutch and when I press on the clutch pedal it unlocks and get on first position. Can you give me any advice to how to lock it properly so that it stays on first position
Пікірлер: 42