Thank you for taking the time to do this video! people like you are awesome. I just bought a 1998 zx6r and doing a lot of research . Thank you once again.
@joelitodiaz
5 ай бұрын
Nice video man! Question, I need to change the valve cover gasket on mine, do you know if I can get to it from the top by removing the tank and what below it, or will I need to drop the engine from the bike?
@Bikerrep
5 ай бұрын
It’s possible to do this with the engine mounted, best you look up the original service manual of your bike for the right handling.
@joelitodiaz
5 ай бұрын
@@Bikerrep awesome, thank you!! I'll do some more research too!
@AndyBop
6 ай бұрын
Hey man I'm not sure if you've still got this bike, but could you do any follow up videos on it? I've owned the exact same one for 6 months now as a project bike and had turned it around to be a mint bike. I just want to know what were your experiences were with it. thanks
@Bikerrep
6 ай бұрын
Unfortunately the oil pump gave up a couple months after due to overheating.
@AndyBop
5 ай бұрын
@@Bikerrep That's really unfortunate, did you lose all motivation to get it fixed or was it far too much labour than what it was worth?
@Bikerrep
5 ай бұрын
@@AndyBop The bike was no longer of value for this fix, too many unknown of what damage was done in the engine.
@odgeUK
6 ай бұрын
When you removed the calipers, did you let the brake fluid drain completely out, and have to replace and bleed an empty system?
@Bikerrep
6 ай бұрын
Yes for a rebuild you remove all fluids, afterwards you use new brake fluid to flush the system and remove any air. If you disconnect the callipers you always have to bleed the system again.
@chocolebumbiker
Жыл бұрын
What’s up brother how are you? Hey, I wanted to ask you a question, I still have a zx6r from 2002, but it’s been 2 times since I’ve changed the clutch bolt and the bar that pulls that bolt, and the bolt seizes and the bar that pulls that bolt cuts or breaks pero, you do not know what could be the problem? greetings
@Bikerrep
Жыл бұрын
Could be a wide range of problems, Have you followed the original service manual? Did you torque correctly and have you replaced any other parts that might need adjustment after?
@odgeUK
Жыл бұрын
08:43 - How important is it to get the right torque on the Caliper bolts? Just hand tight? They seemed to be done up pretty tight when you released them at the beginning.
@Bikerrep
Жыл бұрын
The original torque spec was probably good but the bolts had sealed up completely. I used the drill to get them in fast, after that just proper hand tight. All bolts had a new coating of blue locktite, and until now there were no issues with the calipers anymore
@odgeUK
Жыл бұрын
@@Bikerrep Thanks! This video is really helpful. I need to recondition my own, as the dust seals have perished and have caused the brakes to stick, so watching this very carefully! :)
@harveyfrisby7654
Жыл бұрын
Where did you get the calliper rebuild kit from ?
@akuma6465
2 жыл бұрын
Nice
@TrejoL
2 жыл бұрын
How many friction Plates are?
@7KingCobra7
Жыл бұрын
that's good and all but.. we need to get you some calories!!!
@Galerare
Жыл бұрын
Do you know the torque spec for the clutch springs and the cover? Thanks!
@Bikerrep
Жыл бұрын
Clutch cover bolts, 12 NM Clutch spring bolts 8.8 NM
@Galerare
Жыл бұрын
@@Bikerrep Thank you! I torqued my spring bolts to 12 nm, and they suddenly wasnt tightening anymore 😂 I learned now
@eduardoguedesbh
Жыл бұрын
Tenho uma dessa verde. Está molhando uma vela com óleo.
Пікірлер: 26