Thanks for watching. If you enjoyed the content please give a thumbs up 👍🏻 And if you want to see more, hit that notification bell 🔔 Godbless 🌳🚐
@danfall8233
11 ай бұрын
Mines just gone too at 150k miles, very grateful for the video! Workshop manual is OK, but much more helpful being able to see the job done =)
@MrRanDomUk
11 ай бұрын
Great to hear!
@UP_YRS_NWO
8 ай бұрын
Just been under mine to do the hand brake cables, drop links, lower control arms, front and rear discs pads and full engine service, right as I finished I noticed a drip of brake fluid from this slave cylinder, time to get the tools out again 😂
@paulhughes8724
9 ай бұрын
Same just happened to my van thanks for the video
@mrdynamic7887
9 ай бұрын
My slave cylinder has the same nipple just wide open but one clip for a Citroen nemo is the bleeding still the same mate😎
@NevilleHayfield
Жыл бұрын
Wicked video. I followed easily. Top vid 👏🔥 Only trouble with my car is. Where you sit the new part mine sits in with the pump. Bit open. The plate that it sits in that you said pushes it in. Is already out. Hope I've explained it enough. When I put my part in where you close the pump mine goes in open. Any idea what to look at next?
@clivephillips6758
Ай бұрын
Nice one! 👍
@MrRanDomUk
17 күн бұрын
Thanks! 👍
@tajwalikhan5082
9 ай бұрын
Great Video thank you
@leechafer8855
2 ай бұрын
Just picked up a 2008 and got clutch issues, peddle all the way to the floor and cannot pull it back up and the slave cylinder is all the way out fully extended, any ideas. Great video by the way
@pauldavis7743
2 ай бұрын
Very helpful 👍
@Peter-fckyt
2 ай бұрын
Hi mate. Today on the way to work, after 10 miles, the clutch pedal became soft half way through and it started slipping badly. Clutch was replaced 2y ago and not slipped until today. I have noticed that the slave is not compressed fully when the clutch is not pressed. I can still shift gears but feels like the pedal was not fully reversed and there is a delay in reaction after pressing it. Do you think it will be slave that's at fault?
@jasonhorseman3041
8 күн бұрын
hi mate, just watched this video and found it good, I have a berlingo 1.6hdi 08 plate on 154km my pedal is staying down but I can lift it up with my foot and keep driving, few days ago my brake light came on then this happened, it was hard to get gears then I topped up fluid and it do seem better, is this likely to be slave or clutch
@MrRanDomUk
7 күн бұрын
Definitely the slave
@jasonhorseman3041
7 күн бұрын
yes definitely the slave and changed it last night for £20
@radovanpanic4897
3 ай бұрын
Thanks for the great video
@NevilleHayfield
Жыл бұрын
I've just watch your video again and where you said it sits in the plate so when you push the clutch it pushes it forward. My plate. The exits in is already forward. The clutch pedal was like yours was just loose ? Any help would be much appreciated 👍🙏
@MrRanDomUk
10 ай бұрын
sorry for the late reply , did you get it sorted
@shefflad6461
5 ай бұрын
Great video pal👍🏻 where abouts did you get your parts from?
@MrRanDomUk
5 ай бұрын
Gsf or euro car parts I think
@Muntahaalqdarneh
Ай бұрын
Can I ask you question about my car
@brunostajduhar7159
Жыл бұрын
I have a problem on a Citroen C4 II, the clutch squeals a lot, the sound comes from the cylinder, is it possible that the piston guide on the cylinder is broken or does the ball on the thrust bearing fork need to be lubricated
@MrRanDomUk
10 ай бұрын
sorry for the late reply, did you fix the problem?
@brappres
Ай бұрын
Followed the instructions but still no pressure how long was you pumping the clutch with your hand just not working
@MrRanDomUk
17 күн бұрын
Make sure you open the tap for the air to exit, once fluid starts coming through you should be ok
@andrewrobertson9845
12 күн бұрын
Put cover back on when fluid leaks from tap? Also do I push the 2nd clip in after bleeding?
Пікірлер: 28