Well done. You explained everything at the perfect speed and detail. I have Vetric that came with my CNC Shark and am building a plasma table now. Can't wait to try what I learned here!
@regpugh9021
3 жыл бұрын
Greg, Thanks for your e-mail, just subscribed to your channel. I have learned more about vectric/plasma control in your 20 or so minutes that i have all day. Thanks for that, clear, concise video. Regards Reg retired 75 UK Wales
@spidey4fun
3 жыл бұрын
I have cut 2D!!!! Thanks for this!!
@victortresvik573
10 сағат бұрын
i am using Vcarve pro for my plasma / router table.. where and how did you set up the tool for plasma Thanks
@Oséascachoeiro
3 жыл бұрын
Excelent !!!
@riverbottomband
9 ай бұрын
I'm trying to setup my PP from Aspire for my home built CNC plasma. Do I need a different PP for every different thickness metal I cut? The reason I ask is because or pierce height and delay will be different according to thickness cut? Thank you for all your help in the CNC community around the world. I have watched many of your videos and read many of your forum post. I have been using a cnc router for a long time but getting into Plasma.
@cortegrabados3279
3 жыл бұрын
add plasma post processor ????
@ramonplanell3927
3 жыл бұрын
Muy interesante y muy didáctico
@rafaellopezmartinez2548
3 жыл бұрын
Hola te enseña a hacer el postprocesador? Es lo que no entiendo no se inglés
@sintoniaarteeserigrafia8786
4 ай бұрын
Olá tudo bem, e como adicionar uma pausa de 0,5 segundo antes do corte ?
@fryscountrylifechannel4437
3 жыл бұрын
Could I talk you into doing a video on your plasma cutter table?
@fryscountrylifechannel4437
3 жыл бұрын
Thanks for sharing this I have VCarve desktop and a router cnc, and a plasma torch and now a new project. I hope you don’t mind if I pick your brain or ask you for some already created gcode?
@cahnekad7129
3 жыл бұрын
How to add plasma post processor. Help me
@carroceriasnicar
3 жыл бұрын
If you get it, let me know why I need the same thing
@dandelikakhiladi8452
3 жыл бұрын
Hi ,sir nice video... Which controller did u use (Hard wear)
@Greolt
3 жыл бұрын
If you watch the video you will see that I use UCCNC. It utilises its own hardware. AXBB-E ethernet controller in this case.
@jorgeluispalafoxgarcia3243
2 жыл бұрын
Hola, soy de mexico y me gustaria que me pudieras asesorar de como hacer mi posprocesador, manejo Drufel CNC
@Greolt
2 жыл бұрын
I am Australian. Only English. Sorry.
@marvinpagaran8092
2 жыл бұрын
hope you can share the post processor
@Greolt
2 жыл бұрын
I could do that but it WON'T BE ANY GOOD to you. It is specific to my plasm, control software, THC, even to my personal edits of the control software. Macros are written in the language required by the software used. You need to understand what YOUR setup needs in the way of gcode. THC requirements. Macro language Etc. Watch my video showing writing a generic Post Processor for a guide. kzitem.info/news/bejne/opWKxWGcq6ieY6A
Пікірлер: 23