I'm guessing nothing stays stock in your garage huh ?..It's all good tho..You got the need for speed,hahaha 👍
@Black66
3 жыл бұрын
Yes, we have the need for speed. We had this Coleman bike for about 12 hours before we tore off the stock carburetor lol
@yardsticksteve
Жыл бұрын
This guy doesn't even use stock in his chicken noodle soup
@malikmazyck9683
Жыл бұрын
For those who are like me that’s not trying to spend money all you have to do is zip tie the spring that’s on the governor under the gas tank and that will stop it from engaging. Zip tie it tight and I promise u will see a big difference mines go 41 mph and all it cost me was 3 dollars for the pack of 100 zip ties lol
@Black66
Жыл бұрын
Check out the Ct200U-EX playlist and other playlists for zip-tied governor and many other combos with this bike. Thanks for watching! kzitem.info/news/bejne/uWaJ03WQg2iiim0
@stonesbouldersbones
8 ай бұрын
Actually that mod doesn't work man, it just turns the spring into a linkage. To gain any rpm you have to move the spring outward. Stop spreading misinformation
@Ksvgfuifjs
7 ай бұрын
@@stonesbouldersbonesit got mines up to 43mph with no other mods 🤷♂️🤷♂️ Edit: 45**
@xavieralt2498
6 ай бұрын
@@stonesbouldersbones Ur the same type of person that says u dont need an aluminum flywheel when u rev past 4800rpm
@giovannihenry2343
3 ай бұрын
Thank you gonna try it out
@mikesbarn1858
2 жыл бұрын
I got my ct200uex used for $100 because it had problems. The head was never toqued down. Barely finger tight. The cylinder was full of water and the intake valve was open and rusted. Modded it out and now it’s a blast.
@Black66
2 жыл бұрын
That's the way to get them ! The cheaper the better
@ontheflipsideedc
2 жыл бұрын
I’m about to buy one of these, but I’m a noob. I’ve rode mini bikes my whole life and I know simple stuff, but a governor removal like that is like rocket science to me.
@Black66
2 жыл бұрын
You can do it. It’s not to bad .
@ontheflipsideedc
2 жыл бұрын
@@Black66 just got it today. I’m still nervous about totally removing the governor, but I’m pretty sure I found a way to bypass it with a zip tie. Do you know of the method I’m talking about?
@Black66
2 жыл бұрын
@@ontheflipsideedc Congratulations! Yes, the zip tie basically turns the spring into a straight rod so the governor mechanism cant pull back the throttle.
@ontheflipsideedc
2 жыл бұрын
@@Black66 I’ve heard a few people say that doing that mod can potentially cause valve float and I’m not trying to get that deep into the bike, but I did do a couple other little mods, I cut the throttle stop screw off and shortened the spring on the throttle cable stop thing, and I moved the spring that we were talking about previously to the farthest hole on the governor arm. Went from 19 mph to 25 mph. But I am trying to get to about 30-35 mph. So there’s more work to be done, just not exactly sure what yet. Might go with a torque converter, might just downsize the rear sprocket and upsize the clutch sprocket. Haven’t quite decided yet. I love the torque on this thing though and I know changing the sprockets can mess with the torque. Thanks for your help though and my apologies for my long rant lol
@Black66
2 жыл бұрын
@@ontheflipsideedc With a 40 rear sprocket and a torque converter. The bike will be quicker and faster than stock. The torque converter makes up the difference in torque loss and then some, from the 40 tooth sprocket.
@user-ot3wg5lq3p
2 ай бұрын
I am boring lol I kept mine stock for years now and I use it a LOT . Going for years now. Really enjoy seeing people doing mods.
@Downtown.TonyBrown
2 жыл бұрын
I can not express enough how fustrating it is to see you make it easy, I broke my throttle cable and this probably the best route for me to fix it, now to only figure out how to put this modification on. working on mechanical stuff should be pratice for monk training.
@julian5443
Жыл бұрын
i’m honestly about to tear my whole house apart in a fit of rage because of this same stupid problem.
@Downtown.TonyBrown
Жыл бұрын
@@julian5443 what's going on?
@user-ru7he6qj2w
Жыл бұрын
It’s really easy once you do a full tear down once or twice.
@eddiesheeran5791
8 ай бұрын
He's been doing things like this for decades brother, don't get discouraged! Keep at it!
@Downtown.TonyBrown
8 ай бұрын
@@eddiesheeran5791well that was a year ago, I had to sell it lol I'm broke now. Appreciate it though
@fatbuddycat
3 жыл бұрын
I'm digging this build! I'm considering a small tire ultralight but where I live the terrain is a serious drawback for small displacement and sprockets.
@Black66
3 жыл бұрын
Now that would be a cool build if you could get an area to run it. I would like to see that
@smallengines4us922
3 жыл бұрын
Mine went 35 with the stock carburetor and governor removed. You should remove the muffler and put a header. It will up the speed to about 38 with the mikuni. These are very fun bikes and you should consider buying a torque converter, specially with the weight of these bikes. I otherwise do love this build
@Black66
3 жыл бұрын
Oh ya for sure !! I really want to add that torque converter .
@smallengines4us922
3 жыл бұрын
@@Black66 i have a stage 1 kit and a torque converter. It goes 43 without the governor. Also lowers the cruising rpm. Really good investment
@Black66
3 жыл бұрын
@@smallengines4us922 A torque converter would really make this bike fly. . We have a few more videos on this bike . But no torque converter yet.
@smallengines4us922
3 жыл бұрын
@@Black66 can’t wait to see em’
@goadmerle
2 жыл бұрын
I have 2 of these the ct200u-ex and the bt200x. Both stock clocked at 15-16mph stock. Cut governor screws off now 25-27mph. So interested in what the stage 2 kit will really bring it to. But im thrown off by them saying stock is 25. Because both mine came governed at 15mph. I purchased 1 in Missouri and 1 in California.
@paulcondie2520
Жыл бұрын
Cars n camera who? Lol. Black 66 is my new mini bike channel! Subbed cause I like what I've seen so far. 💯💪🇺🇲
@Black66
Жыл бұрын
Thanks! Thanks for watching the videos!
@brianclark740
Жыл бұрын
I have one of these. I can't wait to tear into it
@eyehearther111
3 жыл бұрын
Its such a fun ride, can't wait to make it faster!
@anthonygendron5648
3 жыл бұрын
A way to make this minibike faster for free (if you have the means necessary to add/remove links from the chains) is to remove the two middle sprockets and drive the rear wheel directly from the clutch on the engine. If your chain has a little bit of stretch in it it works better. Your acceleration will be worse, but I gps tested top speed to 44 mph (23 mph before)
@Black66
3 жыл бұрын
Oh ya, I hear ya. We could do that but we like doing things the hard way lol. We got this bike to 45 MPH in our later videos with the jackshaft. We added a header pipe, 40 tooth sprocket, and a 7-degree keyway. Check em out.
@CreatureOfTheWheel
Жыл бұрын
I do the same thing and it indeed is way better! I went to a larger rear sprocket to compensate for the loss of bottom end and I use a skateboard wheel as a tensioner/guide. I agree you gotta run a little bit of slack🤙👊
@keithcola9104
3 жыл бұрын
I knew it was coming been looking for it!!😁 I wish u were my neighbor lol
@Black66
3 жыл бұрын
That is awesome!! I wish you were too. We did more after this video. It gets faster lol
@nb5316
3 жыл бұрын
Man bro you are one smart man you're like MacGyver you can modify anything and that Colman is sharp looking bike keep wrenching love to see your work !!!!!
@Black66
3 жыл бұрын
Thanks! Appreciate that
@rustybeatty6567
2 жыл бұрын
Hey Black66 you should have bought a Trailmaster MB200 or hurricane 200x in stead and and swapped the factory 196cc engine for a tillotson 212 and then installed a 12 front sprocket and done a full stage 1 performance upgrade and that is a high performance intake bigger main jet high performance exhaust and governor removal.
@Black66
2 жыл бұрын
That's one I can still do later on.
@lilbeviltwin
3 жыл бұрын
Hell yeah can't wait to see more upgrades.
@Black66
3 жыл бұрын
Thanks!! Ya, we have quite a bit more stuff we're gonna do to it.
@lilbeviltwin
3 жыл бұрын
@@Black66 sweet 🤙
@bradcarpenter2396
2 жыл бұрын
Black66 thank you for your input about main jets, I ordered a set but haven't arrived yet.
@apexlucas
2 жыл бұрын
I had a torque converter and a stage 1 kit on my ct200u ex and I hit 50 mph with the governor
@stanlucas665
3 жыл бұрын
When building a throttle cable for a Mikuni from an old throttle cable, use an axle spacer from a slot car. Safety tip, when starting your minibike or go kart, always put the front against a wall or something solid just in case you have a run away throttle.
@bankrollalmighty40
3 жыл бұрын
I have the ct200u-ex and whenever I turn it on the bike just starts going full throttle any suggestions on how to fix that?
@stanlucas665
3 жыл бұрын
@@bankrollalmighty40 Did this start after repairs or modifications?
@bankrollalmighty40
3 жыл бұрын
Yea it started after I did the modifications
@stanlucas665
3 жыл бұрын
@@bankrollalmighty40 What modifications did you make?
@bankrollalmighty40
3 жыл бұрын
I took off the governor and I also installed a vm22 mikuni carburetor on it
@Deucealive75
3 жыл бұрын
That worked better than most. They usually get 31-32 at valve float with the stock gearing. You were turning around 5900 RPM.
@Black66
3 жыл бұрын
Yes, this bike runs really well. We have some more videos coming up. We got it to run faster yet.
@valentinsoto4146
Жыл бұрын
My mini bike is the rt200 stock straight chain stock just govenor removed and tops out at 55
@MrLordfizee
2 жыл бұрын
Nice learning new tricks
@troy22nd
2 жыл бұрын
Nice, the black one wasn't available I had to go with the red one.
@Black66
2 жыл бұрын
Nice color! I have had the Coleman bike to 63 MPH, check out the video kzitem.info/news/bejne/tqZsuqSAoqGheKQ
@ViperX260
Ай бұрын
would of been nice to see how to hook the throttle up to the stock carb for the govern removal
@Black66
Ай бұрын
Check out he B200 playlist. Shows stock carb hook up without the governor
@GenZBiker
Жыл бұрын
I have the same bike & also removed the external gov assembly. Just to be clear, did you guys ever remove the internal gov parts? If not, did you blow up the engine over time? Id love to be able to continue to run this engine with the mikuni carb but worry itll blow up w no gov.
@Black66
Жыл бұрын
Check out the Coleman CT200U-EX playlist. We used this engine for many different part combs over the last couple of years. kzitem.info/news/bejne/uWaJ03WQg2iiim0
@GenZBiker
Жыл бұрын
@@Black66 Just finished watching all the vids in the playlist. Great selection of content man. Can you confirm you never built the internals on the 196 or removed the internal gov? I have a built engine on the way in the next month but wanna enjoy the stock engine till then.
@rockets4833
9 ай бұрын
Was there any issues only removing the governor arm and not the actual governor inside the engine?
@Black66
9 ай бұрын
No issues while the 196 was on the bike. Check out the CT200U-EX playlist for many engine and part combos with this bike.kzitem.info/news/bejne/y36cn62AppOLf3Y
@natebessette273
2 жыл бұрын
Hey i put a new carb on and took the governor off and replaced the throttle now when i start my bike it just runs wide open and takes off by itself?
@dunamon
2 жыл бұрын
My baja had the same problem. I put it up on a wooden box to free up the rear wheel. There are three holes on the governor arm where the spring from your throttle connect. I removed that spring & brought it to hardware store. Bought a bunch of similar springs that are the same length. Some tigher some looser, all the same length. You can also go on amazon and order kits of springs for you ride real cheap.. Use the new springs and try fitting it into 3 different holes of that gov swing arm. You will get the right fit sooner or later. Got mine to stop running wild at idle. Also GAINED 6 MPH!!
@michaelanderson6215
11 ай бұрын
What happens if that clip falls off that round deal you took the arm off under the gas tank? Serious question will something catastrophic happen or no?
@filipinokidd0655
7 ай бұрын
It won’t fall in there cause it’s has a clip stoping it from dropping
@tonypolaroid3405
2 жыл бұрын
I Need help I need to find a dirt bike carb for my Coleman bt200x mini bike Someone help!
@meanmansur
Жыл бұрын
Quick question my minibike turned off while riding now when I turn it on it only goes 10 mph or less and doesn’t get any faster
@jeffreygordon2864
9 ай бұрын
Have the same problem
@brianmcnamee2240
2 жыл бұрын
If you hadn’t put in the mikuni carb where would you have attached the throttle cable to?
@Black66
2 жыл бұрын
Check out this playlist on my cc200u. Same set up with the re-jetted stock carb kzitem.info/news/bejne/u3yCuZakqHpmbJw
@ant-lr5iv
2 жыл бұрын
Black 66, I need help again lol. I have a torque converter kit for a coleman hisun and now im switching it over to a tilly 212. The 4 bolts that hold the torque converter to the block are not threading in fully and im afraid im going to strip the threads in the block. Are these bolts the same size for both the hisun and the tilly or are they different? The bolts thread in a couple of threads but then stop. I appreciate all the help you offer.
@johnwick-ii6il
2 жыл бұрын
WARNING : Do not leave the governor mechanism inside the motor. It can, and will, come apart or move around where it will break the oil slinger off of the connecting rod.. Even the smallest broken pieces will jam the compression release from working.....or worse. If you must leave the inner workings in place, then re-install the lever and tie it into the far forward position. This will keep the inner assembly from coming apart.
@Black66
2 жыл бұрын
Please read my channel description and disclaimers in the video's. I tell people not to do what I do. if you do, you do it at your own risk. This is what this channel is about. Testing different combinations and doing things most say I shouldn't. By the way, I have had this bike on the channel for over a year with many different combos on the stock internal 196cc without ever opening the case. This is a durability test. It has passed so far. Check out the playlist. Thanks for watching the videos. kzitem.info/news/bejne/uWaJ03WQg2iiim0
@MRGreen79
Жыл бұрын
@@Black66 how did you keep the governor arm from spinning?
@GenZBiker
Жыл бұрын
i wish i could see a picture of what you mean by tying it into the far forward position. I put a mikuni carb on & naturally the gov assembly no longer functions but quite frankly I wish i could’ve just kept the gov funtioning. Im getting a built race engine next month so for now i just wanna ride it with it governed.
@DavidZamora-jl3vb
Жыл бұрын
@@GenZBiker what kind of motor fully built are you getting? And where can I get one? I have a Coleman CT 200 U.
@GenZBiker
Жыл бұрын
@@DavidZamora-jl3vb It will be a Ducar 212 that Im having a local Wisconsin builder make for me!
@GliblyUnited8billion8
2 жыл бұрын
An another thing when you were plugging up the whole you said you can use the sealer of your choice what is the name of sealer that you used an were can I get it at? My apologies for all the questions I'm new at this but can't wait to get this show on the road 😂
@Black66
2 жыл бұрын
loctite will work
@GliblyUnited8billion8
2 жыл бұрын
You got back to me quick lolz thank you👍
@mikepence7847
Жыл бұрын
What did you do with your throttle cable? I did exactly what you did and now my cable sticks in WOT after taking the springs off. I don’t understand
@Cal3b587
3 ай бұрын
I just got a arco bushwacker with a lifan 196 on it im excited to throw a mikuni clone on it
@hevid79
2 жыл бұрын
So did you use the original cable and just modify it or did you actually use the cable that came in the kit and did you have to modify that cable ?? Any details would help us out, thanks for a awesome video !!!
@Black66
2 жыл бұрын
Modified the stock cable. You can solder a new tip on the end. Or zap the cable with a welder to put a new end on it.
@Noprivacy666
2 жыл бұрын
So you can leave the governor in the engine like that
@Black66
2 жыл бұрын
It’s always recommended to take out the governor wheel in the crankcase . Just one less thing to come apart . But with that being said a haven’t taken this one out or even opened the case with no problems at all .
@flojotube
3 жыл бұрын
You’re not EXPLAINING anything you’re doing to the noob viewer… Youd probably find yourself with plenty more views & engagement if you’d actually share what you’re doing with the rest of us… Other than that, good stuff.
@IDontKnowLuis
3 жыл бұрын
Whats the governor?
@dallias347
3 жыл бұрын
@@IDontKnowLuis governor is like a stopper of how fast u can go on a mini bike, remove that and you can go so much faster, there’s 2 ways😂
@helenabasquette7222
2 жыл бұрын
whoa the black back ground is freaking me out KZitem MAKE IT STOP
@jrc-fabs1634
2 жыл бұрын
Hi, what are your thoughts about getting a bullet flywheel for this engine after getting a stage 1,2, or 3 performance kit. Do I need it?
@Black66
2 жыл бұрын
Yes, a billet flywheel is definitely a good idea. Or at least one of the cast flywheels that is rated to 8500 RPM . They are inexpensive good insurance. I use one in the budget 212 build on the channel .
@rexmontana3058
Жыл бұрын
Been watching a lot of your videos…lots of great info. I was just handed a Baja mb200…at least I’m pretty sure that’s what it is. Looks the same as your Coleman but the frame is different. Same 196cc engine that’s locked up. The bike was barely used and left sitting outside for a few years. So I got a new predator 212 non hemi for $150 and am getting ready to put it on there. It appears that it will bolt directly in place. I remember this bike being slow and I’d really like to have a bit more go…will the predator make it faster by doing nothing else? Or do I need to remove the governor? Mostly just want to ride some trails with my son, but occasionally I might wanna ride down to the store or just ride to the fishing hole…thanks!
@Black66
Жыл бұрын
Thanks! MB200 is a nice bike. The governor will definitely hold it back. If you don't want to do anything else throwing a zip tie in the governor spring will wake up the Predator like in the Predator free mods video. If you start spinning it faster it is recommended to upgrade the flywheel . kzitem.info/news/bejne/2mmm0muBooWFoI4
@rexmontana3058
Жыл бұрын
Watched that video and it was helpful. I’d like to see it go about 35 maybe….I think I’ll be happy with that for now, is the stock carb on the predator 212 good for that? It seems the Mikuni sticks out a bit and I’d be worried about taking a spill and breaking something.
@jackievanhelen
Ай бұрын
Gods I love you
@itwaswritten804
2 жыл бұрын
You did all of that masterful removal and installation for the bike to still be slow as hell. THANKS BUT NO THANKS
@Black66
2 жыл бұрын
This is one of many combos. Check out the playlist kzitem.info/news/bejne/uWaJ03WQg2iiim0
@205_AJJ
Ай бұрын
i have an issue on mine where when you crank it it full throttles and the throttle isnt engaged and then when you try to accelerate it slows down like the throttle needle is up when you start it and when you acelerate the needle goes down and it wont stop i have to hit the kill switch anyone know any solutions?
@SpAcEcruizer203
3 жыл бұрын
go over that coleman logo and put one that reads BLaCK66
@Black66
3 жыл бұрын
Good idea!!
@SpAcEcruizer203
3 жыл бұрын
@@Black66 of corse dude THANKS FOR KEEPIN THE DREAM ALiVE!!!!! pASS it on
@Black66
3 жыл бұрын
@@SpAcEcruizer203 yes!! Gotta keep it goin
@SpAcEcruizer203
3 жыл бұрын
@@Black66 idefinitly so on the contrary im trying to go viral so im gonna come out with this ticktock thing called the shadow dance if china catch on to it before me im screwed ill be under 100 subs forever basically u film your shadow dancing and be like oh shadow dance lmao wtf
@SpAcEcruizer203
3 жыл бұрын
@@Black66 wat ya think bud kinda fruity rite lol
@aronjones1821
2 жыл бұрын
i bought an aftermarket cable to do exact setup as you instead of modifying existing one, the one i bought was 50" long but seems to be about 2.5" too long. any suggestions?
@Black66
2 жыл бұрын
Guess you could always cut it and zap the end with a mig welder to create a new tip or solder a new tip on it . About 2 and 1/4 sticking out of the end is about right for the vm22
@Gh..o..s..t
2 жыл бұрын
7 plus mph gain thays awesome
@Black66
2 жыл бұрын
Thanks! Check out the other videos on this bike. We got it to run even faster
@tyeirvine3615
Ай бұрын
How do you reassemble with the stock carburetor? Wish you didn’t skip over that part.
@Black66
Ай бұрын
Check out the playlist on the channel for stock carb videos.
@NBProductions2023
2 жыл бұрын
Hey black 66 I got a mikuni but I put it on and the engine sounds like it’s going to blow up do you have any tips? I was thinking re jet Btw it’s on a brand new no mods at all predator 212
@Black66
2 жыл бұрын
Maybe try the procedure in this video kzitem.info/news/bejne/rqSH3H2if4ppm4I
@BrickzSTM
2 жыл бұрын
Is there an alternative bike with similar specs and frame etc? I've been looking for one for several months. I can't buy this in Europe/Germany over the normal sites because they don't offer international shipping and I can't find it on Ebay or Amazon etc...
@johnk6346
3 жыл бұрын
Just wait till I get done building my mini bike. I am going to pass you like you were standing still.
@Black66
3 жыл бұрын
Yes! because you have that secret engine. The one you used in the time machine.
@ryanilano2869
2 жыл бұрын
Hey man I've got basically the same ct200u-ex setup and I'm having trouble with it stalling would you have any idea why?
@biffwhippster6184
2 жыл бұрын
awesome build but would’ve been better without the stock exhaust :/
@Black66
2 жыл бұрын
Thanks! Check out the playlist for the CT200U-EX The bike has had many combos without the air box . The channel is mainly about testing different combos. kzitem.info/news/bejne/uWaJ03WQg2iiim0
@fallingalloy1389
5 ай бұрын
I have the same exact kind and I was hoping if u can upgrade mine
@jv.lyfestyle1010
Жыл бұрын
Great video, What size fuel hose did you use for the tank going to the carb...
@Black66
Жыл бұрын
Thanks, the fuel line is linked in the description of the video. Check out the CT200U-EX playlist for many more engine and part combos with this bike. kzitem.info/news/bejne/uWaJ03WQg2iiim0
@dylanpetrin9584
2 жыл бұрын
I bought a go kart off Facebook market place and the guy I bought it off of him and his kids pulled the governor out and the go kart top out at 50mph the scariest part about me owning it was the fact the right front tire was missing the cotter pin so the wheel would wiggle when you drove it when I got it I drove it in the drive way A little and noticed it but I was determined to see how fast it went so I drove it on to the road and just hit the gas and just risked it (Note) I did not have a helmet on at the time lmao
@josephhasbrouck4795
2 жыл бұрын
Just removed mine completely and put the 18lb springs in . When putting the throttle plate back on with the stock carburetor, where do I put the spring so the throttle doesn’t stay wide open? Thanks ahead of time
@Black66
2 жыл бұрын
Check out this video. You can see where I put the springs. kzitem.info/news/bejne/znqVu6qagqNipWU
@deejaysheltonjr8574
Ай бұрын
Hey I did this and put it back together because i needed to by the mod. But when I put it back together and everything is where it's supposed to be.... When I start it it's runs but when I hit the throttle it doesn't do anything... But when I turn the choke off the wheel starts spinning... How do I make it normal
@426superbee4
2 жыл бұрын
idk where they get it as 196 cc? lts a 50 cc engine ~ might be even a 90 cc > Make the glove box a functional fuel tank on top make the bottom a tool box or make a tool box on back of the seat
@Black66
2 жыл бұрын
I did that with the fuel.tank . Check out the playlist
@426superbee4
2 жыл бұрын
@@Black66 Very cool
@ChristopherJones16
3 жыл бұрын
I heard some guys using fishing line weights on the end of their throttle cable which they then solder shut after they pinch them on.
@Black66
3 жыл бұрын
There are a lot of different ways to do it. I like taking all of the governor hardware off. It makes the engine more clean-looking that way.
@chadsenters00
Жыл бұрын
How did you get the original throttle cable to work I swear I did the exact thing and it binds and I get so much free play and half throttle
@Black66
Жыл бұрын
Maybe there is to much cable sticking out for the slide...
@chadsenters00
Жыл бұрын
Any adjustments that would fix my issue or just replace with new throttle cable all together?
@peniaji_yt5762
2 жыл бұрын
Guess what just happened, the same coleman mini bike you have right now, when I left the black fuel choke on while the motorcycle was off, gas was leaking and as soon was I ride the mini bike, the motorcycle was caught on fire and now its ruined, is there any way you can send me some link options on Amazon I can buy to get the new engine. It can be the 212 predator.
@peniaji_yt5762
2 жыл бұрын
@@Black66 I should show you the video on my tiktok what it looks like it's damaged
@fourthwheel8787
3 жыл бұрын
I don’t know if you already answered this question but, what size did the carburetor’s jet come in?
@Black66
3 жыл бұрын
It had a 98 in it when I got it .
@Carey802
Жыл бұрын
Can you please tell me what the two pink tubes connect to? It seems you have them just dangling below the carb. Also, what about the tubing that connected to the exhaust?
@607rocket
Жыл бұрын
If that has a variator trans setup, like a scooter, you can get a few more mph buy taking to spacer out of it.
@Black66
Жыл бұрын
Check out the CT200U-EX playlist. We got this bike over 60 MPH so far. Thanks for watching! kzitem.info/news/bejne/y36cn62AppOLf3Y
@Farmtractor
3 жыл бұрын
I would love to do your modifications. Is the flywheel going to explode at your rpms? I’m worried about that.
@Black66
3 жыл бұрын
I have never had a problem with one at the level this engine is at . If I was to add a cam and billet rod and other parts to increase the RPM potential, then I would start thinking of adding a billet flywheel .
@Farmtractor
3 жыл бұрын
@@Black66 thanks for your quick response! Another question I had is the reliability of the engine. How reliable would it be with these mods? Would it harm the engine?
@Black66
3 жыл бұрын
@@Farmtractor This is one of the bikes we actually ride around a lot . It has been rock solid with months of riding so far. . The 196 cc seems really durable . The only problem we had to fix so far was the chain on the jack shaft .
@Farmtractor
3 жыл бұрын
@@Black66 that makes me feel very confident. Thank you so much! I’ll have to try this out!
@jaydenstewart2847
2 жыл бұрын
I put a mikuni carb on my bike (exact model in vid) and it takes off even when I am not on the accelerator. How can I fix this?
@Black66
2 жыл бұрын
Check out these two videos. They might answer your question. Thanks for watching! kzitem.info/news/bejne/w2uYv2FnoHuIiqA kzitem.info/news/bejne/rqSH3H2if4ppm4I
@emoya319
3 жыл бұрын
Hey man I have a question for you. Would you say this carburetor mod is fairly simple to install? You made it look easy but Im sure That comes from experience lol, long story short I tried to change my Jet on my Stock carb, but the old Jet got stripped somehow and it became a shit show, so now I have to upgrade it fortunately.
@Black66
3 жыл бұрын
Super easy! My next video on Saturday is doing another carb. It's not on this bike, but it's the same process. Check it out.
@emoya319
3 жыл бұрын
@@Black66 forsure man i look forward to it. I need to get my little baby On the road i just installed my torque converter and it’s night and day difference so I can imagine am upgraded carb haha good stuff thanks bro! 👍🏻
@KOOLPOP01
Жыл бұрын
Ik it’s from a while ago but can you explain in more depth?
@daveecklund3369
8 ай бұрын
Don’t you have to remove the governor internally for it to not engage?
@Black66
8 ай бұрын
Check out the CT200U-EX playlist for part tests and engine swaps along with governor removals on the CT200U-EX kzitem.info/news/bejne/y36cn62AppOLf3Y
@jimmoss4148
2 жыл бұрын
Question… I’m on the Mikuni website, what size carb should I buy for my 196cc Coleman? There are so many different carbs to choose from! I don’t want one that’s going to be to much or not enough for the motor. What size/model carb did you guys use?
@Black66
2 жыл бұрын
I used a VM22 on this build Because it is easy to tune, the low cost and it supports future upgrades better than the stock carb. There are others I have used on the channel that have better performance but cost a little more. Check out the CT200U-EX playlist kzitem.info/news/bejne/uWaJ03WQg2iiim0
@1koolblue
Жыл бұрын
Thank you for the video, I did this mod but I left the governor arm connected. Does that make a difference?
@bankrollalmighty40
3 жыл бұрын
I have the ct200u-ex and whenever I turn it on the bike just starts going full throttle any suggestions on how to fix that?
@Black66
3 жыл бұрын
If the twist grip itself isn't stuck back then Look where the cable goes into the linkage. There is a screw there that holds the cable housing onto the linkage. Also, make sure the cable itself didn't slip out of its fastener where it connects to the linkage. Makes sure all the springs are connected.
@bankrollalmighty40
3 жыл бұрын
Ok thank you
@roypatterson9910
3 жыл бұрын
Only 33 mph with a Mikuni carb and the governor removed??? I just bought the exact same one a week ago and all I did was cut off the throttle stop screw and zip tied the governor and mine goes 30 mph, 31 mph downhill. I was thinking about getting a KX-80 2-stroke engine or an engine off a KX-100, which would make it fast as hell! Shit, I might put a 1000 cc street rocket engine in it! Lmao
@Black66
3 жыл бұрын
You are right, the stock carb can definitely get you into the thirties. The real reason for the Mikuni that a lot of people don't realize is if you are planning to do future modifications, The Mikuni will support the future mods with ease. It is super easy to tune. We have had this bike into the fifties in future videos.
@shawn1472
3 жыл бұрын
Hello. For the mikuni was it the 22mm or the 26mm? I have the same bike.
@Black66
3 жыл бұрын
It's a VM22 Mikuni but the actual venturi size is 26mm
@SpAcEcruizer203
3 жыл бұрын
how can i tell if my gov is removed do i have to take apart the engine its the stock motovox one that comes with the Motovox
@Black66
3 жыл бұрын
If you see that little rod that sticks out of the crankcase that connects to the throttle linkage then it's still in there.
@SpAcEcruizer203
3 жыл бұрын
@@Black66 hey i think its not there because when i pull the throttle only the cable to the carb moves they have the throttle where your talking about bypassed or somethingdam i wish u can see it are u on messenger or facebook
@SpAcEcruizer203
3 жыл бұрын
@@Black66 would the mikunni vm22 fit on my motor or are they just for the preds n tillys
@Black66
3 жыл бұрын
@@SpAcEcruizer203 It sounds like it is bypassed because normally when the governor is connected the linkage will move along with the carb. I'm not on Facebook. I need to sign in again.
@Black66
3 жыл бұрын
@@SpAcEcruizer203 It will but that is a small engine for a VM22. I have a video that isn't out yet where I install a 19mm Mikuni on a Coleman three horse. It makes a big difference on that little engine.
@nicolec7290
2 жыл бұрын
You unhooked the governor but didn’t take it out. Did you just leave it set
@Black66
2 жыл бұрын
This is a test bike on the channel. I wanted to see what the long term effects would be without taking out the nylon wheel.
@Partnerthedog
3 жыл бұрын
So where you removed the governor arm, has it ever moved and died all the sudden? Or is it that simple. You made it look so easy and way simpler than factory..
@Black66
3 жыл бұрын
Ya, it is that easy . The Mikuni makes it so easy . Basically pull all the factory stuff off , install the carb , good to go . I really like the Mikuni . No messing with all that linkage , brackets , arms none of it .
@BradFFA
2 жыл бұрын
@@Black66 does this apply with my c100 212?! Just picked it up tonight and it’s a torque monster completely stock!
@elcuh7939
2 жыл бұрын
Can you please give me advice I installed a mikuni carb on a 200cc stock Coleman motor with a governor delete and swapped a 125 jet the throttle response is amazing but the idle is too high and I already adjusted the idle speed screw all the way out i don’t know what it may be
@Black66
2 жыл бұрын
If there are no leaks anywhere, this video might help , here is the link kzitem.info/news/bejne/rqSH3H2if4ppm4I
@curtisbrown5254
2 жыл бұрын
I really appreciate your videos and viewer engagement. I tried that soldering trick on my cable and can't get it to stick well. I get it on there, let it cool and when I pull the throttle it comes off. Do you have any suggestions?
@Black66
2 жыл бұрын
Thanks! Ya, you definitely want to get that thing to stick really good. Don't need that coming off while the engine is running. Use some paste flux on it and then let the iron sit on the cable tip until it gets really hot. That way some of the heat is in the cable and then apply the solder. That way it penetrates into cable as your applying the solder. . If you have a MIG welder or a flux core wire feed welder you can simply clamp the ground on the metal cable and then just tap the electrode on the cable really quick. It will leave an end on it. If you don't have that you can use a handheld propane torch to solder it on there too. just be careful not to overheat the cable. Sometimes it will get too hot for the solder. You could always just grab a proper length cable with an end already on it .
@curtisbrown5254
2 жыл бұрын
@@Black66 Thanks. I ordered a proper length cable with the end on it. Out of curiosity, would a ball of epoxy work too?
@Black66
2 жыл бұрын
@@curtisbrown5254 Im not sure. I have never tried that. It has to be something that wont come off while the the engine is running or the engine might not be to happy.LOL
@sjvieaux8312
27 күн бұрын
Why tear it apart when all you have to do is remove the governor linkage? Way easier with same results lol
@Black66
27 күн бұрын
The channel is about having fun with minibikes and testing minibike parts . Check out the over 400 videos on the channel. Thanks for watching!
@emjester48
2 жыл бұрын
I’m not sure if you answered this question or not but I’m going to order this carburetor for mine tomorrow do you happen to know the fuel size needed? And Did you have to use any adapters to connect it to the gas tank, only reason I ask is I know on the Honda gas tanks the nipple on the tank is smaller than the carb and I haven’t pulled this one apart yet . Thanks in advance
@Black66
2 жыл бұрын
No, I didn't use adapters. The jetting might be different than mine because of my elevation, engine mods etc. Check out this video on VM22 tuning. kzitem.info/news/bejne/rqSH3H2if4ppm4I
@emjester48
2 жыл бұрын
@@Black66 Alright I’ll check it out, do you know the fuel line size by chance you used?
@Black66
2 жыл бұрын
@@emjester48 The links for the parts used is in the description
@SpAcEcruizer203
3 жыл бұрын
what did u put voodoo on this vid man i cant stop watchin it
@Black66
3 жыл бұрын
Yes! lol It's😂 going to make you watch it over and over lol
@SpAcEcruizer203
3 жыл бұрын
@@Black66 thats messed up man hay when u gonna get a motovox frame like mine it has good front suspension ..ur bke is cool tho too that green one is crazy fast now huh i bet u scared to drive it
@Black66
3 жыл бұрын
@@SpAcEcruizer203 ya, I want one like your math at frame is sweet . I’ll try and get one . I tried that ten tooth on the little bike . It made it quick quick , but it tops out quick too so I put the 12 tooth back on until I can get a different rear sprocket so I can balance it with a little more top speed
@jacksonclar9130
2 жыл бұрын
So yeah I installed my mikuni I see their is a pin where the governer is my thing is pushed all the way down my question is I start riding my bike which is the same one you have and I go 3/4 throttle and the bike goes back and forth and slows down same carb thanks if you can answer back
@Bigredboyd70
2 жыл бұрын
So when you say you removed the governor, you just removed the all the hardware on the outside of the engine… you didn’t remove the internal governor gear… correct
@Black66
2 жыл бұрын
No, I have never opened the case on this engine . It still has the nylon wheel inside
@SIpMadeRj55
2 жыл бұрын
Quick question i did all the stuff you did and mine just wont start i checked the spark plug and every thing what do i need to do
@timwalters5736
Жыл бұрын
Hey what app are this guying to keep track of speed?????
@Black66
Жыл бұрын
I use digiHUD on the phone along with the camera GPS for top speed and a Dragy performance meter for 0 to 30
@seanh6134
11 ай бұрын
So you dont need to remove the internals like you would on a like a honda engine, when removing the governor???
@Black66
11 ай бұрын
The channel is about testing different parts and engine combos. Check out the CT200U-EX playlist for many engine combos with this bike and others! Thanks for watching. kzitem.info/news/bejne/uWaJ03WQg2iiim0
@seanh6134
11 ай бұрын
@Black66 I mean that's a generic automated sounding response, I'm looking for a yes or no lol
@randyramsay8469
Жыл бұрын
I have a Massimo Motors 200cc(196cc) minibike with centrifugal clutch and jackshaft, 19in wheels and the bike weighs 164lbs, I weigh 135lbs and current sprocket setup is a 10t to 20t-10t to 50t and I have a GPS top speed of 31mph. Used GR calculator and the math isn't right..Says my top speed should be 20mph. Everything is stock. I want more torque with minimal loss of top speed.. Please help!!
@terryhenry275
2 жыл бұрын
Where can I get replacement emissions tube for vm 22
@Black66
2 жыл бұрын
Here is a link. Thanks for watching! www.ebay.com/itm/124839200549
@troy22nd
Жыл бұрын
How safe is it to ride without the governor?
@paulortega2550
2 жыл бұрын
When you take off the braket on the governor gear you just leave the gear in there and remove later? Could that effect anything in the future?
@Black66
2 жыл бұрын
It's best to take out the gear. Less stuff to go wrong. I did leave the gear in this engine just to see how it would hold up over the last year. There are a few videos on the channel of me taking out the gear. Here is one of them on a Predator 212 kzitem.info/news/bejne/zm6XtYCjrqydeG0
@NeenertinsBBQ
2 жыл бұрын
What happens if you don’t take out the gears?!
@samsonmartinez9773
Жыл бұрын
Did you have to take the side casing apart and take the governor gear out ?
@Black66
Жыл бұрын
This is one bike in the fleet that I havent taken out the governor gear. Definitely a good idea to take it out.
@samsonmartinez9773
Жыл бұрын
Thank you so much I appreciate you taking time to reply
@handymanmeraz
Жыл бұрын
How many inches on the throttle cable in to the carburetor do I need?
@chadlinkhart755
2 жыл бұрын
When you took the governor off how fast did it go after that because I'm looking into getting one of these we have a lot of Bio trails and this would be great for me to be able to get my daughter one also while she's on for college and we can go trail ride ing may 3 so really looking for a good price especially since I'll be purchasing two or three
@Black66
2 жыл бұрын
Check out the playlist on this bike. It takes you through the mods we did...kzitem.info/news/bejne/uWaJ03WQg2iiim0
@s10w_b0i8
2 жыл бұрын
So I had taken off the throttle screw and now I can only control the speed by adjusting the choke on the engine itself. Any ideas?
@Black66
2 жыл бұрын
Did you accidentally unhook the throttle spring ? The one that runs from the linkage to the governor arm?
@s10w_b0i8
2 жыл бұрын
@@Black66I know that the tinier spring had come loose and fell off, I reconnected it to the small hole on the carb and to the linkage arm, when I try to use the throttle on the handlebars it only moves the throttle spring and wire but not the governor or linkage
@s10w_b0i8
2 жыл бұрын
I’m using the stock carb for now until I get my mikuni in
@Black66
2 жыл бұрын
@@s10w_b0i8 The Mikuni makes things a lot cleaner and easy to work on
@fatbuddycat
3 жыл бұрын
Take off the stock choke lever and stick that cylindrical end in the fuel line, that's what it's for but nobody knows it!!Why else would it be shaped like that?? It's so when you are servicing the motor you can plug the supply line.
@Black66
3 жыл бұрын
Good tip!
@heavybass7825
Жыл бұрын
Hey I wanted to know will this mod work on a predator 212? And also do you think I could just leave the governor arm on and tie it off so it doesn’t engage and then add my Mikuni carb?
@VictorGomez-tt3fs
Жыл бұрын
When u add the mikuni carb does the mini bike start going and u don't touch the throttle?
@kevinholland4156
2 жыл бұрын
Do you know what Mikuni carburetor I should get for my 79cc Predator?
@Black66
2 жыл бұрын
Yes, check out the Micro bike playlist. Links for the carb is in the description of the videos. Thanks for watching ! kzitem.info/news/bejne/pX93tm2knIl2eKA
@kevinholland4156
2 жыл бұрын
@@Black66 Thank you
@bradygainey8043
2 жыл бұрын
I remember back when I was a kid my father told me that taking the gov off of my go cart would explode/destroy the engine is that true and is it true for go carts and dirt bikes alike
@bradygainey8043
2 жыл бұрын
@Dave N thanks
@bradygainey8043
Жыл бұрын
@Danang Alta do you know how I could do this with no risk like adding parts to it
Пікірлер: 456