3:05 white powder? for a minute I thought we were about to discover the source of Hambini’s weird erratic personality. A bit of Charlie
@reginaldscot165
4 ай бұрын
If he’s sniffing aluminium oxide it would definitely have some effect on his mental stability. 😂
@AQWorldsLPC3675
Ай бұрын
Jesus, that is literally the worst mechanicing (if that's a word) I have ever seen!!! I have always been a bit suspicious of Hambini but this train wreck means I cannot ever take him seriously again!! I would honestly sack any mechanic working for me for practices like this! Thanks for highlighting this.
@reginaldscot165
Ай бұрын
You are welcome, he is not what he seems. 😳
@simonalexandercritchley439
7 ай бұрын
Another Hambini roast. Standard engineering practise is to grease any metal/ composite interface/threads. He may be an aerodynamicist or whatever as well as a plumber but not a mechanic I would trust.
@reginaldscot165
7 ай бұрын
Not sure what he is but I also don’t trust his work.
@jimbo9030
9 ай бұрын
Also, why did the compression plug have to come out, especially if your going to bash on the steerer? Leaving the compression plug installed at least means you're hitting metal and not raw unsuppored carbon. Also how he just keeps bashing it risking the compression ring to gouge into the steerer 🤦 Just a little tap to get some play and then push the steerer back up to release the compression ring from the bearing and the ring just slides off and the steerer drops. Also just clamp the seat post and tilt the bike down and that way nothing can fall anyways. I've never seen an "expert" litteraly get every step of the most basic maintenance task wrong 🤦
@reginaldscot165
9 ай бұрын
It’s totally insane, to think people consider him the “expert” on everything now. 🤔
@scooterchannelanddoityoursel
10 күн бұрын
January 1986, space engineer Hambini speaks to he masses, he emphasizes his masterfully work on the Challenger Spaceship, a few hours before the launch 😂
@reginaldscot165
10 күн бұрын
🤣🤣🤣
@cd0u50c9
4 күн бұрын
Oooooof that joke burned up on ascent....
@MrBirdshell666
9 ай бұрын
maybe the message of the video was "how to do it wrong"?😢
@reginaldscot165
9 ай бұрын
Then I approve this message. 👍🏻😁
@stfu6397
2 ай бұрын
his bike is an absolute mess, wouldn't want to own that bike even if you gave it to me for free
@reginaldscot165
2 ай бұрын
Agreed. 👍🏻
@rfons07
8 ай бұрын
Thanks for the informative video on what not to do on a headset service!
@reginaldscot165
8 ай бұрын
Well, you can thank Hambini for that. 😅😉
@johne1956
3 ай бұрын
Wow, I like watching Hambini but this was painful. How can he do so many things wrong in what is a very simple job.
@reginaldscot165
3 ай бұрын
Good question, maybe he isn’t very good at mechanical things? I also used to watch his channel, until he decided to completely lie about me and my tools. 🤷🏻♂️
@hankschrader2353
9 ай бұрын
Crazy state of the bike….
@reginaldscot165
9 ай бұрын
I’ve seen worse… unfortunately. 🤣
@Nivacromcolumbus
Ай бұрын
So bad for an engineer, unbelievably crap. That is the work of a 5yr old
@reginaldscot165
Ай бұрын
I agree and yet he has a massive following of loyal fans who think the sun shines out his bum?
@Nivacromcolumbus
Ай бұрын
@@reginaldscot165 the video was bad, but I must admit he is brilliant in certain areas. Def a BB specialist, and he does point out how crap QC is with carbon crap.
@Emtbtoday
8 ай бұрын
Hes not even using a Torque wrench on a carbon head tube waw! 31.38 the top cap the back is higher than the front like he's stripping threads not putting it back in straight!.be why it's screaming!
@reginaldscot165
8 ай бұрын
Agreed 👍🏻
@alvaroduarte6597
9 ай бұрын
He is not the neatest mechanic/engineer but this service deserves a badge of dishonor; Sewage headset service by a 5 yrs old!
@reginaldscot165
9 ай бұрын
Agreed 👍🏻
@Monkey_slapping_keys
9 ай бұрын
You seem to like taking shots at him but as a point so does he to others. He puts his work out so it’s open to criticism, all is fair.
@reginaldscot165
9 ай бұрын
True. Agreed 👍🏻
@FL-ym6hm
9 ай бұрын
Disagree! It’s the manner in which Hanbini takes his shots. Doesn’t need to use profanity all time. Shows his lack of maturity.
@baldyslapnut.
9 ай бұрын
@@FL-ym6hmHe doesn't claim to be mature.
@mike_f
8 ай бұрын
@@FL-ym6hm Which part of "by hambini aged 5" part did you miss?
@jumbo_mumbo1441
4 ай бұрын
If he's this wrong, it doesn't matter at all how polite he is. He's politely showing people how to mess up their 5 thousand dollar bikes
@martinb9032
4 күн бұрын
I am a complete amateur bike mechanic but have successfully looked after my 4 bikes for years now. I would never count myself as an expert but this clown does ?? When he preloaded his top cap i nearly screamed out. U need to just take the play out the system then maybe an extra quarter of a turn for luck. Technically u can remove the top cap once the stem bolts have been tightened up but I wouldn't. I would never have done that even at the beginning of my maintenance journey. And the wooden mallet. Wtaf 😅. I've heard mapdec raving about hambini and this is the man himself ? No thank you won't be listening to his opinion about anything
@reginaldscot165
4 күн бұрын
Yes you are a much better mechanic. I can bet money on that! 😅
@blackcastle5140
9 ай бұрын
I appreciate the first video I saw of you debunking Hambini about striking a bearing vs using a puller but watching this video? Oh man, saltiness is in the video. You are just going overboard, to the point that I can also smell jelousy. Stop using Hambini on your videos, instead make videos that contradict him and other "wrong" mechanics without mentioning their name, make your own name without riding someone else's name. Disclaimer: I am not a Hambini fan, I am not an expert(that is I'm watching bike videos) and English is not my native language but this will be the last time I will watch your videos. I did not even finish watching this video because all I can feel is saltiness. Good luck.
@reginaldscot165
9 ай бұрын
Well I might not agree but I really respect your ability to make yourself well understood in a foreign language. 🙏🏻👍🏻🙂
@lukediamand1694
9 ай бұрын
This video needs some kind of content warning. Watching that bike getting that treatment has left me traumatized. And what's going on with that bar tape?
@reginaldscot165
9 ай бұрын
I’m sorry, I really should have considered that! 😅
@oldiegoldie-j4h
9 ай бұрын
Please, don't get too harsh with this 5 yrs old engineer and his beloved hairdryer. 🙏🏻
@reginaldscot165
9 ай бұрын
His hairdryer? 😁 that’s a fun fetish. 😉
@hugonotti9192
3 күн бұрын
was that hambini video a halloween video??? Arggg!
@reginaldscot165
3 күн бұрын
Maybe April 1st. 😂
@scooterchannelanddoityoursel
10 күн бұрын
Hambinis work is horrible, hammering the carbon fork is crazy, also his bike is so dirty and rusty, he doesnt care about his bike.His bike is in a horrible condition, absolutely disguisting.
@reginaldscot165
10 күн бұрын
Agreed. 🙁
@PixieDixie-r5v
10 күн бұрын
I can feel your frustration. Reginald, and mine , too! Holly Chromoly!
@reginaldscot165
10 күн бұрын
Indeed! Thanks! 🙂
@iansellers1251
9 ай бұрын
You sure this wasn't a joke video ?
@reginaldscot165
9 ай бұрын
No… I’m not sure at all. 🤷🏻♂️😆
@aybee69
8 ай бұрын
I'm wondering the very same thing. This was painful, yet hilarious, to watch.
@nayanpati7310
16 күн бұрын
30:27 my ears hurt listening to that squeaking sound. Damn that bike is screaming for help. He tightened that top cap way too tight.
@reginaldscot165
16 күн бұрын
Totally agree. What’s crazy is some of his fans try to pretend everything here is totally fine. Just like the meme of the dog in the burning house: “this is fine.” 😆
@thebikerepairshopformby
8 ай бұрын
I as a rule dont like people point scoring off each other, I would never criticise another persons video. However I was pretty shocked at the poor practice in this video. Its certainly not the way I work. I also cringed at the top cap being tightened, that was pretty much the worst thing on the video. This is after all a pretty simple job for a decent bike mechanic 👍
@reginaldscot165
8 ай бұрын
But is it a simple job for a aerospace engineer? 😂 Well normally I wouldn’t “point score” but he made the mistake of lying about me and my tools in his video so now the gloves are off! 😉
@tristano1998
6 ай бұрын
@@reginaldscot165“…the gloves are off“ - understandably.
@cd0u50c9
4 күн бұрын
I've not seen this video of his before, and I do admit I've followed him for some time. But it does go to show that just because someone works with stringent tolerances on components in a different field altogether, doesn't mean that he's a competent BIKE mechanic, or any good at dealing with bikes specifically... Surely his video is a skit?? There must be a disclaimer somewhere?
@reginaldscot165
4 күн бұрын
He certainly has not admitted it was a troll. In fact he defended the video by saying “I don’t care about my bike.”
@cd0u50c9
4 күн бұрын
@@reginaldscot165 You can certainly tell he doesn't care for his bike. Might be after a payout for new teeth....
@MilosBalunovic
8 ай бұрын
sorry to brake your logic but your brake on pushing on the bolt straight.. you are wrong. if you have a rubber, tightened at the "entrance" of the friction force, as you brake harder, the tension on the brake pad will elongate it thin it out (reducing the thickness of the pad), and also start tearing it. the bolt of the brake pad is not meant to hold the braking force, but just the rubber insert not to fall out. if you have it as shown in Hambinies video, you will have compression in the direction of braking force, making the pad thicker and also it will be butting up against the insert holder. also you will have more pat material where your biggest braking force is generated... from most of the comments it seams that you are trying to find a way to make it look worse than maybe it is. 1st of, you assume the video is uncut and every part of the video, blt not being tight is as is... the wheel was supported by the tool drawer from underneeth... which you would see maybe... but to your credit you have a lot of good points and explanation
@reginaldscot165
8 ай бұрын
Sorry I found this comment impossible to understand. I’m guessing your first language is not English? If you can get a friend who speaks better English to help with making this comment clearer I will happily try to read it again. 👍🏻 Or maybe try Google translate, that seems to work well for me. All the best! 👍🏻
@cd0u50c9
4 күн бұрын
Milose, naopacke je stavio paknove...
@drivemenuts3011
9 ай бұрын
From viewing this video of his, he looks like an amateur bike mechanic. But many of your criticism of him in your video show that you are often wrong as well (from his response video), and yet you claim to be a trained bike mechanic. It seems weird that you have had to go back 5 years into Hambini's history to find something wrong. Greasing the bearing seating is optional. I apply a very small amount. The grease shown in the mountain bike video was excessive. That much grease is a great muck accumulator.
@reginaldscot165
9 ай бұрын
So you do use grease? So do I. So what’s your argument here? Hambini wasn’t wrong because? It’s only optional if you want the bearings to rust and you want to do a bad job. Everything he did during the video was completely wrong and every justification for doing it in his recent video was a bare faced lie. When you have been a bike mechanic as long as me and serviced as many bikes you would be able to see his lies more easily.
@drivemenuts3011
9 ай бұрын
@@reginaldscot165 I'm not making an argument. I am leaving a comment. That, with the exchange between the two of you, you both seem to make a lot of mistakes. With the mistakes that Hambini has pointed out about you, I wouldn't use you as a bike mechanic. On the flip side, the five year old video of Hambini's bodgey skills is unrepresentative of his current skills. I would also not use him as a bike mechanic as he doesn't look after his own bikes. However he is an expert at bottom Brackets. I would consider sending my frame to him, if it had a major BB problem. So, you seem to be the slightly better (or less bad) general bike mechanic, but he is far superior in the BB repair area.
@Ian-Saxon
20 күн бұрын
This is a parody or wind up from Hambini surely???
@reginaldscot165
20 күн бұрын
Ha ha if only! 😅
@yamyam60
5 ай бұрын
That ratchet head resting on the frame...................mmmmmmmmmmmmmmmnnnnnnnnnnngggggggggggghhhhhhhhh
@reginaldscot165
5 ай бұрын
😳
@Emtbtoday
8 ай бұрын
14.23 whats up with that tyre the rubber looks all deformed that bike Looks like a barn find but hes got the garmin on it so is this a daily driver? No i hope not its someone who doesn't appreciate what they have!
@reginaldscot165
8 ай бұрын
I didn’t notice the rubber. 😳
@Bonky-wonky
10 күн бұрын
An engineer designs stuff, a mechanic repairs it. Two different skill sets so I think it’s a bit of a cheap shot to slate him for being a bad mechanic.
@reginaldscot165
10 күн бұрын
I’m no good as a welder. I’m terrible at it. You don’t see me making videos on how to weld something. Do you understand?
@Bonky-wonky
10 күн бұрын
@@reginaldscot165 hambini’s channel is about engineering, the few bits of wrenching are purely illustrative and aren’t meant to be a guide on how to work on your bike or show his mechanical skills. In life we sometimes do stuff we’re not particularly good at. You are pretty bad at communication yet you still engage in it. Grow up and accept the fact that you’re clearly just bitter about him being critical of your work.
@user-cx2bk6pm2f
9 ай бұрын
The backwards brake pad is telling. As an engineer, I'm an electrical engineer, your job is ALL ABOUT DETAILS. Small details. Large details. All of them. The more critical the detail, the more attention you pay. If you're a good engineer, this mindset is ingrained into everything you do. If you're not a good engineer, well, you might mount brakes backwards.
@reginaldscot165
9 ай бұрын
Worrying isn’t it. 😳
@peterch4978
8 күн бұрын
Hambini failed here as bike mechanic
@reginaldscot165
8 күн бұрын
He did, totally. 🤭
@billyshakespeare17
4 ай бұрын
Ham could paraphrase Dr. McCoy's (Star Trek) favorite declaration: "Damn it Jim, I am an engineer, not a mechanic".
@reginaldscot165
4 ай бұрын
He could indeed. But McCoy would never try to demonstrate how to fix a warp core. 😉
@nadsim154
3 ай бұрын
That video was gold dude... Looks like the aerospace oil imagineer got reamed !
@reginaldscot165
3 ай бұрын
Yes it was rather fun, pass it on for others to enjoy. 😁👍🏻
@simonalexandercritchley439
7 ай бұрын
Specific greases and weights are needed for each application. E.g ti prep for titanium etc. Where 2 different metals contact each other there is galvanic corrosion. Water and salt is the catalyst therfore cleaning and re-greasing is needed more in wet or dirty conditions. This maybe stating the obvious but it is often neglected.
@reginaldscot165
7 ай бұрын
I totally agree. He recently started that he had never herd of corrosion with aluminium and stainless steel… can you believe that coming from an aerospace engineer?
@kajkob
2 ай бұрын
@@reginaldscot165yikes, can you link where he says that? Find that pretty shocking
@Miraflores1990
8 ай бұрын
I see many efforts to destroy hambini's reputation, why so?
@reginaldscot165
8 ай бұрын
If telling the truth destroys your reputation then it’s not much of a reputation. The main reason for me personally is A) I’m the only person brave (or foolish) enough to speak against him. (I believe that there needs to be balance against his cult of personality that he has manufactured) B) he lied about me and my tools after all I did was prove he was wrong. And that was only after he mocked and suggested I didn’t understand something that actually I knew better then him. He is a liar, a charlatan and a hypocrite. And it’s my job to prove it. 🙂
@Miraflores1990
7 ай бұрын
@@reginaldscot165 Fair enough. I see him exposing crap about other brands. I guess is taking his own medicine. I agree with you about Brake pads, no grease everywhere, and poor methodology. I would also add that for the reaming bottom bracket should use the "Parktool 744 40.98mm Reamer" and not a sand machine. But I don´t agree with giving an opinion about how to treat his own bike or criticizing how rusty it is in a 2017 video. Also, remember this is not his job, So he is not receiving insights like you or me from the market. All in all, we all know how the persona hambini is, and brings lots of joy to listen how crap is the rest of the world. Maybe he can take advice from this video instead take criticism from it. Thanks Reginald
@kris8165
9 ай бұрын
For the life of me, I don't understand why he didn't remove the front wheel, before removing the fork... I'm not skillful in anything,and I can be a bit of...cluts😅 but I would definitely remove the wheel first, before removing the fork,to be serviced,greaced, cleaned, whatever... Why he didn't loosen the screws,when removing the stem... Again...idk😅 And that squeaking sound when installing the stem on the steerer, I mean...why making it harder than it has to be..And no lubricant of whatsoever????? Man.. And... just because someone is highly educated engineer, doesn't mean he's good with tools,or just plain old bike service! We learn..!😅😊 Greetings from Croatia from Kris 😎
@reginaldscot165
9 ай бұрын
My feelings exactly. 🙂
@waiakalulu7544
9 ай бұрын
His destructive approach to things is ridiculous to the point of being beyond belief.
@kris8165
9 ай бұрын
@@waiakalulu7544 I kinda like the dude! He can be very informative,and even funny 🤣 But watching that service video,idk... I thought engineers know better,or something 😅
@larrymcgoldrick3471
9 ай бұрын
A Master Class in how NOT to service your headset. Not all mechanics are engineers and not all engineers are mechanics.
@reginaldscot165
9 ай бұрын
True 👍🏻
@brianmcnelis2440
3 ай бұрын
This is a lame video.
@reginaldscot165
3 ай бұрын
If you think this is bad you should see the original! 😂
@paulbowerbank1900
9 ай бұрын
To be fair to Hambini, that video appears to be from 2017. His maintenance skills might have improved a bit since then.
@reginaldscot165
9 ай бұрын
That’s true… but he is trying to show people how to do it. 🫢
@garyfodden5034
9 ай бұрын
so why doesn't he remove that video and make one that shows the right way to fit new headset bearings?
@carl90210
9 ай бұрын
I hope so, for the sake of the aerospace industry 😁
@tomekborucki1120
9 ай бұрын
Because he believes he does the job righr.
@Frankrezzo24
9 ай бұрын
OMG what did I just watch? This is even worst then a novice diy!! The brake pads In reverse, no proper tools , the corrosion! Not removing the wheels , the bar tapes , clamping on the top frames , not putting grease etc etc . This is aerospace standard!
@peglor
9 ай бұрын
There's one subtle issue glossed over in this video that is worth mentioning - the clamp bolts on the stem should be tightened and loosened incrementally, alternating between the 2 bolts, in order to ensure the loading on the clamp is reasonably even from top to bottom at all times. A quick thought experiment to explain why - If both bolts are initially evenly tightened and one is loosened completely, then the remaining tension (Which is more than the tension either bolt was carrying while both were tight) is carried entirely by the remaining bolt, leaving the bolt and more importantly the clamp loaded significantly more than they were when both bolts were tight. Similarly, when tightening the bolts, if you tighten one bolt up to the recommended torque and then tighten the second one, also to the recommended torque, the first bolt will now be loose. This is not mentioned even in the official instructions for installing a lot of parts with paired bolts on the same clamp, so you can follow the official installation procedure to the letter, using a torque wrench and still have a dangerously installed stem with a loose stem bolt afterwards. A scenario where this is even more important is on Hollowtech II crank pinch bolts, where the bolts are even closer together and in the much stiffer clamp at the end of the crank. It takes a little longer to tighten and loosen paired bolts like this (Especially on cranks where you usually have to spin the cranks 180 degrees for access each time you switch bolt), but at least you can be sure they are sharing the load evenly and the part is firstly clamping firmly enough to stay in place and secondly that the stress on the part is carried evenly across the clamp as per the part's design. Speaking as both a very well qualified mechanical engineer and someone who worked on and off for over a decade as a bike mechanic, that Hambini video is absolutely shocking from both sides of the fence. One trick I have seen, and even occasionally used, with GT85/WD40 is when MTBing in extremely muddy conditions is that spraying the downtube and chainstays with WD40 just before going out riding in thick mud does stop mud sticking to the frame, for a while at least.
@reginaldscot165
9 ай бұрын
Excellent comment and a very interesting point about the bolt tightening process. I must admit that I do know that you should follow that protocol, but sometimes I don’t… for the cranks I almost always do, it’s become second nature by this point. Thank you for the detailed explanation. Always good to hear from an expert. 🙏🏻🙂
@82vitt
9 ай бұрын
Shimano manual for their 105/Ultegra/DA groupsets does say the tightening of those crank arm pinch bolts must be done incrementally. I always initially use just an allen key for the first coupe turns until the second bolt stops getting loose when I turn the other one, then switch to a torque spanner and do them up alternately to 3/6/9 and finally 12Nm. For stem face plates where there are mostly 4 bolts the tightening is done incrementally in a diagonal pattern too.
@skogling
Ай бұрын
Shajt.
@reginaldscot165
Ай бұрын
Yup
@SamSung-ej3qr
9 ай бұрын
trying to go head to head with Hambini is a bad idea
@reginaldscot165
9 ай бұрын
I disagree, it’s amusing and very successful. 😉
@gatopirao
6 ай бұрын
So it's OK to spray your frame with GT85 (with all its rough aditivites) all over but not good to put a small amount of grease between the bearing and the frame... blimey!
@reginaldscot165
6 ай бұрын
Logical reasoning. 👍🏻🙂
@tristano1998
6 ай бұрын
Yes, this is a really strange thing what Hambini is doing here. Especially when you know how much precision and meticulousness he puts into his bottom brackets (of which i got a PF30, that works very well). Besides - i am a very thorough „greaser“ myself. I grease literally almost ANY screw on my bikes. Most important: The pedal axis screws! I had a case some time ago with a so-called bike „designer“ who sold me a bike where he had installed the pedals without any grease. It was almost impossible to loosen them later on. Never forget to put LOTS of grease on those threads…
@reginaldscot165
6 ай бұрын
Grease is almost always a good idea, certainly in bike terms. I think the precision of his BBs is over complemented, especially when you consider it’s the very expensive CNC machines at his workplace that he uses for free to make his BBs. When you have industrial grade programmable equipment you didn’t pay for it’s very easy to make precise products. I know this from personal experience: I used to work with industrial welding robots. Now personally I’m terrible at hand welding, I can do it, but I’m just awful. However, when I plug a few numbers into a welding program for a robot that robots makes some beautiful welds that out class the work of a professional hand welder with 20 years experience! Hambini is the same, we see in this video that he is just awful with his hands, not even capable of the most basic maintenance tasks. But, he puts some numbers into a programmable industrial machine and then all of a sudden everyone is complementing him on his work. 😂
@robertoduranos5196
9 ай бұрын
The front wheel was not removed for obvious reasons, it was seized in..
@reginaldscot165
9 ай бұрын
Ha ha ha 😅
@martinjfabbro
9 ай бұрын
What a complet bodge job. The kind of repair you do at the side of the road in an emergency. All in a hurry, no grease, brute force. Apparently the top cap has an integrated bolt. Hambini got himself a bit cocky. You known you're going to be watched by thousands of people. He should've informed himself a bit better and tried to do a more professional job if his intention was to educate people. I can't understand it unless he was asking to get rimmed 😅😂
@reginaldscot165
9 ай бұрын
That bit about the “threaded bolt” is total BS 😂 He’s just lying again. 🤷🏻♂️
@benhaywood2510
2 ай бұрын
Just stumbled on this video, Reginald. Never seen the Hambini video before. I’d just like to say that the jury isn’t out! 😂 This is a genuine “how not to”.
@reginaldscot165
2 ай бұрын
Yes just do the opposite of what he recommends and it would be a better service. 😅
@Emtbtoday
8 ай бұрын
That rust in that steering is exactly what GT 85 leaves for you in winter months! Don't do it!
@reginaldscot165
8 ай бұрын
Yes it’s not the best idea.
@roddas26
9 ай бұрын
He went in dry 😂 My days.
@reginaldscot165
9 ай бұрын
That’s what she said…
@jamesf8864
20 күн бұрын
Wow, this video has just blown my mind! I had never seen that Hambini vid, but yikes 😳 I swear about 50% of steerer bearings out there are under-preloaded (loose), and about 40% are over-preloaded, leaving a sliver of bearings out there actually operating as they should be. That was painful watching Hambini cranking his up so tightly, and crazy to think that that same person actually designs and sells bearing systems (bottom brackets). Not only that, but he has taken on the mission of producing remedial bottom brackets to fix everyone else's flawed designs. That was an eye-opener!
@reginaldscot165
20 күн бұрын
If you think that was bad you should see my other videos on him… 😳 But only if you want to get more shocked. 😅
@jamesf8864
20 күн бұрын
@@reginaldscot165 This was the third Hambini-bashing video of yours that I watched. One comment said that this headset vid of his might be from 7 years ago, so it's feasible that he's learnt a lot in those 7 years, but it's still surprising to see an engineer treating bearings and an assembly in this way. His unsympathetic use of hand tools is also concerning, but then I see a lot of engineers operating tools in this way! My experience is that it's rare for modern engineers to be good at the theoretical AND practical aspects of engineering, which seriously needs addressing. I can't blame you for meeting fire with fire after he tried to call you out. I hope you manage to continue keeping these vids more technically critical than personal and retalliatory 🙂
@johnnybravo0
9 ай бұрын
As a bike mechanic i'm crying as his bike is. That is painfull to watch 😢😢😢
@reginaldscot165
9 ай бұрын
I also felt pain watching it…
@theillegalimmigrant9314
9 ай бұрын
Serious question, Can you explain why you hold your Titanium bike in high acclaim when it has a defective bottom bracket? According to the SRAM specifications, your frame hole is too small. Do you feel that you ignore manufacturer data because you know better?
@reginaldscot165
9 ай бұрын
Not really a serious question is it old boy. 😉 It’s a PF30, in it is a PF30 BB with a 30mm spindle. It spins fine. 👍🏻 Stop trusting people who are dishonest. 😘
@theillegalimmigrant9314
9 ай бұрын
@@reginaldscot165 So you know better than the manufacturer?
@thedronescene7474
9 ай бұрын
@@reginaldscot165So, SRAM is dishonest? I mean the BB specs are on Sram website and on your video it shows your BB be undersized. So who is dishonest, you, Sram or hambini for pointing that out?
@theillegalimmigrant9314
9 ай бұрын
@@thedronescene7474 Reginald is too hurt to admit he has made a mistake. For all Hambini's failings, he readily admits his headset video was rubbish.
@thedronescene7474
9 ай бұрын
@@theillegalimmigrant9314 Exactly! Which is why Reginald should not be trusted. If he cant accept when he is wrong then no one should trust him.
@DaveCM
9 ай бұрын
I have never had to bang out my fork. Maybe a soft tap from my hand, but never had to bang on it like like that. I have a friend who owns a bike shop. She has a "wall of shame". His headset would go onto that wall. And who works on the fork and doesn't remove the wheel?
@reginaldscot165
9 ай бұрын
Sounds like your headset is in good condition. 😁👍🏻
@bruceharris6596
9 ай бұрын
I'm an Aerospace Engineer with vast experience with the big players. I've always been suspicious of your Hambini, Peak Torque experts. It is extremely rare to work and gain working knowledge in a wide range of speciality areas, typically Manufacturing, Composites, Design, Stress, Aerodynamics, Fluid Mechanics etc. They are distinct roles in themselves and you don't move between them and definately not expert in all of them.....
@reginaldscot165
9 ай бұрын
I was also considering that, seems very odd to me to be the one stop shop for all things engineering?
@lovenottheworld5723
9 ай бұрын
They know everything because they read it in a book. Crossing the bridge between the abstract and the practical reality becomes an impossible challenge when the mind is stuck in the knowledge trap. The placebo of mental ascent has deceived the soul. They 'say', but they 'do not'. Woe unto them.
@moshet842
9 ай бұрын
"Composites, Design, Stress, Aerodynamics, Fluid Mechanics etc." - You just listed an array of topics a single aerospace engineer is expected to have, at the very least, working proficiency in. Some specialize, but implying that an aerospace engineer worth his salt, especially one with experience investigating incidents shouldn't be expected to have knowledge in these areas makes me doubt your claim to be an Engineer. If we assume you are right that he can't know all these things, what the hell makes aerospace engineers different from Mechanical engineers then? Hambi/Peak Torque have only made basic engineering assertions that any engineer should know including you if you are one.
@lovenottheworld5723
9 ай бұрын
@@moshet842 Unfortunately modern education has produced a generation of 'knowers' and 'sayers', just don't let them 'do' anything because they'll mess it right up.
@endtimeslips4660
9 ай бұрын
i did cycling years. and i never seen bike look like that. why so dirty. i doubt mechanic bike look like that.
@reginaldscot165
9 ай бұрын
True 👍🏻
@MartinE63
9 ай бұрын
It’s not just road salt, Hambini lives close to the sea, in the well known aerospace capital of the UK, Grimsby😀 That regular ride to ‘the oil refinery’ exposes the bike to wind blown salty sand from the Humber estuary. A few weeks commuting in those conditions and any bike will experience corrosion. Grease would indeed help, GT85, a more expensive version of WD40 aka kerosine with added teflon doesn’t.
@reginaldscot165
9 ай бұрын
I also live by the sea in a very humid climate, my bikes don’t look like that… 😐 😉
@DaveCM
9 ай бұрын
I don't think so. I lived on the coast for several years and routinely rode parallel with the coast with the wind blowing from the water. I've never had anything nearly as bad as that.
@zeez4178
9 ай бұрын
Obviously your just a part timer@@reginaldscot165
@vihuelamig
9 ай бұрын
It's not quite the same as WD40. GT85 contains PTFE which acts as a lubricant. In fact it's often advertised as a 'bike lubricant' although I doubt they intend it for bearings which are more appropriate with grease. For a general frame protector (steel) I use furniture polish, in other words wax. It's not long lasting so it does need to be done on a regular basis.
@donpalmera
9 ай бұрын
@@vihuelamig I guess you shouldn't be spraying anything like WD40 or GT85 all over bearings as it'll dissolve the grease and you'll be left with whatever light lubrication it provides (i.e. not enough for bearings long term). If GT85 is sold as a bike lubricant I guess they would mean for the chain, cassette and so on.
@andrewwarcup684
9 ай бұрын
He was pretty quick to post a reply video, slamming your titanium bottom bracket description.
@reginaldscot165
9 ай бұрын
Must have touched a nerve 😅
@beno9966
9 ай бұрын
The fact Reginald was so wrong about the top cap makes him look a bit stupid though, you have to admit no?
@reginaldscot165
9 ай бұрын
@@beno9966only if he was wrong. And he wasn’t, Hambini is just lying like normal. 😂
@Bonky-wonky
8 ай бұрын
@@reginaldscot165the same could be said about you….
@reginaldscot165
7 ай бұрын
@@Bonky-wonkyonly I back my statements up with evidence and I actually prove Hambini to have lied on several occasions. You might like hambini but “facts don’t care about your feelings.”
@bigredcardigan
8 ай бұрын
Spraying your whole bike with GT85 makes it faster when braking!
@reginaldscot165
8 ай бұрын
So true 😅
@mtbboy1993
8 ай бұрын
7:51 After sending a clarification I did not get any answer from ITM, so I tried to send more info trying to explain what I'm asking, I referenced this video, and shared a link to it, a screen shot. But still no answer. It's simple, thing to answer, is the stem cap threaded? only two options Yes, No. Strange they can't answer a simple question.
@reginaldscot165
8 ай бұрын
I’d bet money it’s not, I found some photos online of the cap and it looks like every other design out there. The only thread one I’ve seen is the FSA one designed for cannondale about 6 years ago. It looks very different.
@mtbboy1993
6 ай бұрын
@@reginaldscot165Update: I sent them a new request, still no answer. Maybe they are ignoring me this time. I don't know. Maybe they are busy who knows. It would be best for them to give a clear answer or even response to Hambini's video if Hambini is wrong. But yes I saw the pictures of it it looks like any compression plug top cap. Or post more pictures.
@Emtbtoday
8 ай бұрын
You'd think for an engineer he'd have the correct tools For working on a bike! Like the headset remover tools ive seen enough 😂
@reginaldscot165
8 ай бұрын
He has the tools, just doesn’t use them… and when he does he uses them wrong. 😢
@alinprema
9 ай бұрын
I laughed so hard when i saw that big hammer in his hand 😂 And the sound of those hits...hahahahaha 🤣 Hammerini making a foul of himself again. I bet anybody will do that job better after watching a youtube video with how it should be done properly.
@reginaldscot165
9 ай бұрын
I hope so! 😅
@tfa8
8 ай бұрын
remember who Hambini or Sanjeev really is: a PhD in Aerodynamics, Lead engineer from a reputable company, 25+ years experience in the job of aerospace engineering, selling bicycle parts on his KZitem channel under as chosen synonom 'Hambini'. If anything above written sounds strange to you, especially the part with PhD and selling bicycle parts: congratulations! You passed the red flag test of how to spot a con artist. Well done. Nothing wrong about selling bicycle parts, but things Hambini claim he is and thing he does on YT doesn't match together.
@reginaldscot165
8 ай бұрын
Totally agree!
@KleineJoop
8 ай бұрын
And why doesn't it match? I don't see anything wrong with him, only you people hating lol
@Savrotir
8 ай бұрын
Lets assume he is in his 40s. Thats a reasonable assumption based on his appearance. 25 years of experience??😅😅😅😅
@theillegalimmigrant9314
9 ай бұрын
Thoughts on the Hambini Christmas Reaming? 😂
@reginaldscot165
9 ай бұрын
Not seen it, busy with family. ❤️🙂
@albertosantangelo6872
9 ай бұрын
Proper reaming
@nickburke5263
9 ай бұрын
Full ream.
@velobey7832
9 ай бұрын
He is like, he does not give a shit about bicycles :D, to me it is kinda shamefull to record "this"
@reginaldscot165
9 ай бұрын
Yes he has expressed that openly. 🤷🏻♂️
@Savrotir
8 ай бұрын
@@reginaldscot165 does he actually ride any bike? He completely ditched dtswiss hubs without even riding one. Of note is that he provided external measurement details on the dtswiss hub proving that is of lesser tolerance of the 9velo. And how about internal measurements? Does he own a dtswiss hub in the first place? Why didn't he show the actual measurements? I got to say Reg. At first i was thinking your beef with him was to take viewers. Now, its that he actually annoys you. Also the guy from zero friction called him out on bearings, he never replied.
@jaladars
8 ай бұрын
It is his own bike he can bodge it as he please I think, like many other home mechanics :D
@reginaldscot165
8 ай бұрын
Not really a valid argument when you are showing other people what to do.
@alankay9225
9 ай бұрын
“Yesterday I couldn’t spell engineer. Now I are one.” 😂
@reginaldscot165
9 ай бұрын
Well I’m a fellow dyslexic so spelling isn’t all it’s cracked up to be. 😅
@emmabird9745
9 ай бұрын
Love it. I've grown up with that joke.
@andrewcalladine2507
9 ай бұрын
I have to say this kind of negative tit for tat video is very childish. Why not just produce a video with advice and not mentioning other KZitemrs. Just because they disagreed on how you measured a bottom bracket!
@reginaldscot165
9 ай бұрын
But this is more fun! 😁
@thedronescene7474
9 ай бұрын
Because this is the only way he can get views. Btw go watch the latest Hambini video! He destroyed this “mechanic”
@sly7917
9 ай бұрын
This Reginold guy is also very disingenious that he's using a 6 year old video which was one of Hambini's earliest videos. The comment section from the original video already tore Hambini a new one which he never took down and has learned from. This guy is simply jealous of Hambini
@quincywalker4441
9 ай бұрын
He’s trying to take the Durianrider approach but it’s not sustainable as making genuine video with genuine ideas maybe harder but yields better retention.
@katerinazhu6268
9 ай бұрын
I wonder how many system and component failures on the F-35 can be attributed to Hambini....
@reginaldscot165
9 ай бұрын
I seem to recall a lot of expensive delays and issues with the project during development… 😳
@phenofinder9145
9 ай бұрын
Very funny but no way would they let him near an f35
@DR_1_1
7 ай бұрын
@@phenofinder9145 Then 737 MAX maybe?
@stevenaaus
9 ай бұрын
Haha.. fun video. He's a bit slack, but you're a bit hard too. Yeah - no grease is dodgy. Bring it on :)
@reginaldscot165
9 ай бұрын
Too hard? That’s what she said…
@petef15
9 ай бұрын
Genuinely can't work out if he's trolling or not
@reginaldscot165
9 ай бұрын
Ha ha I think not… but if he is it’s a massive troll. 😅
@cyclingSausage
8 ай бұрын
Wow, I wouldn't treat my hack bike with so much disrespect! It's obvious he hasn't got a clue.
@reginaldscot165
8 ай бұрын
Shocking isn’t it. 😱
@lucasg2895
9 ай бұрын
He does enjoy playing in the dirt it seems, I remember watching his video on how to service shimano hubs and almost throwing up.
@reginaldscot165
9 ай бұрын
I think I have seen that one. 🤔🙂
@tweed0929
9 ай бұрын
Hambini is right on many accounts and he has a courage for calling out the bike industry that went in deranged mode recently with its unnecessary tech nobody has asked for and insane prices... but then Hambini is absolutely shite bike wrench and I would not let him work on my trusty steel bikes let alone carbon fiber ones... My aluminum seatpost gets off from the steel frame easier than he can drop his carbon fiber fork. Go figure...
@reginaldscot165
9 ай бұрын
Ha ha yeah, you clearly know what you are doing. I think many people are brave enough to call out the bike industry, it’s not like calling out the communist government or something. 🤣
@mtbboy1993
9 ай бұрын
He published a reaming of this video where he claims his top cap has a threaded collar. That does not make any sense to me. Why would a top cap be threaded. I commented and he replied. He wrote wits obvious that it's threaded. Strange. Nothing obvious.
@beno9966
9 ай бұрын
We love for him to prove that. It doesn't really make sense but it's a weird headset.
@reginaldscot165
9 ай бұрын
Yes well the logical and simple answer Is he’s lying. 😂
@mtbboy1993
9 ай бұрын
He wrote this: Hambini wrote: ''It's plainly obvious it's threaded. Saying corrosion was holding it together was the most stupid thing I have heard for some time. I can't believe a "pro" mechanic said that. '' ''Providing you can generate the clamping force, the bearings don't care. I guess the ITM guy didn't care about having logos lining up.'' I will wait and see what ITM(ITALMANUBRI) says in the message I sendt them. If their contact form worked. @@reginaldscot165
@mtbboy1993
9 ай бұрын
They received my email. I will come back with what they wrote. But they needed clarification, as they did not understand my question. So waiting for an answer. @@reginaldscot165
@mtbboy1993
8 ай бұрын
I sent ITM another email. lining to this video and a screenshot. @@reginaldscot165
@Emtbtoday
8 ай бұрын
No grease in the bearing steerer wtf!
@reginaldscot165
8 ай бұрын
I know right! 🤨
@Lacking_something
9 ай бұрын
Are the brake pads on the wrong sides of the bike, thus meaning the direction of travel is wrong? I couldn't tell from the image.
@reginaldscot165
9 ай бұрын
Yes it’s the only way to put them on backwards. The left pad is on the right. And right on the left. 👌🏻
@Lacking_something
9 ай бұрын
@@reginaldscot165cool. I couldn't work out if they could also go on upside down. Those set screws are god awful... So easy to round off the minuscule hex head. That's a LOT of force going through them too... I wonder what their shearing strength is 😮
@al-du6lb
3 ай бұрын
gotta enjoy a good ole reeeeming
@reginaldscot165
3 ай бұрын
It can be fun. 😅
@martingruffalump5484
7 ай бұрын
Pixie dust ALWAYS works!!!!😊😊😊
@reginaldscot165
7 ай бұрын
Well the Muc-off pixie dust normally turns to a goopy mess after a few days. I much prefer the Morgan Blue blend of Pixie dust and graphite powder. 😉
@martingruffalump5484
7 ай бұрын
whoops! - i actually meant REAL pixie dust from fairies and pixies!! - i'd no idea there was any product ripping off the jolly sprinkles from the magical world!! 😊😊😊@@reginaldscot165
@martingruffalump5484
7 ай бұрын
hahahaha - d'ya mean some (clowns) actually called products Pixie Dust!!!!!???? - i actually meant the stuff fairies n pixies sprinkle on things with their stars and magic wands.... 😊😊😊 on a more serious note - ive used graphite on some extreme applications (hot, high pressure, hi revs in excess 100k rpm etc) with great results - its astoundingly good for plastic on plastic rotation and reciprocation too. on bikes i use jst normal stuff - no 'bike' specialised and never had lube or corrosion probs in over 60 yrs biking!! ive watched a good few of u r vids and like u r approach to engineering - use of pullers and pushers - only thing ive ever hammered and then only with a backing dollie was cotter pins - the never to be missed total pia bike bits from the distant past.....@@reginaldscot165
@kulchatha4657
9 ай бұрын
Hambini has just put you to sleep.
@reginaldscot165
9 ай бұрын
Must have been very boring? 😂
@kulchatha4657
9 ай бұрын
@@reginaldscot165 no waking up from that. Cant believe the bull shi you have been telling us ! Disappointed unsubbed
@hamadalshamsi1
9 ай бұрын
Someone is jealous here 😂.
@reginaldscot165
9 ай бұрын
Of who? 😂
@junkandcrapamen
9 ай бұрын
That top cap is obviously threaded to the bolt. Also, do you know any doctors who smoke or drink excessively? He may treat his own bikes carelessly but that has no bearing on his competence.
@reginaldscot165
9 ай бұрын
That was a very poor attempt to defend his incompetence. 😂 and no you are wrong about the top cap but nice try. 👌🏻☺️
@mtbboy1993
9 ай бұрын
@@reginaldscot165Also I live in Norway rid eon salty roads no issues with top cap, I out a bit of grease at the bottom threads and underneath the bolt head. Never gets stuck. To me it looks like months of corrosion by sweat from his head. I ride a MTB so would not be in that position often, but simply cleaning the bike after each ride would help. It's so quick and easy to do. Only times I don't do it is if my back is really bad. He talks about proof about grease attacking the resin but where is it? Where's the proof of the threaded cap? 😁
@MrVizzle
9 ай бұрын
Well now I feel not do bad, working on my bikes like I am not sure what I am doing. Still doing better job than aero engineer... Thanks for video, I really liked that video.
@reginaldscot165
9 ай бұрын
Thank you 🙏🏻 🙂
@waiakalulu7544
9 ай бұрын
My first thought was his actions were just plain inexperience. But I think there's actual ill in his skill and a blithe desire to beat unmerciful on carbon components. People have been slapping things together for years I suppose. But it's a strong reminder why I do all my own work. If I get stranded in the boonies or late for work, I have only myself to blame.
@reginaldscot165
9 ай бұрын
Good comment. 👍🏻
@tornagawn
9 ай бұрын
Whose bike was it? His own?
@reginaldscot165
9 ай бұрын
Thankfully yes. 😅
@MrSzwarz
9 ай бұрын
By the way top cups, require very different tightening forces, depending on brand and type, from 5Nm up to 10Nm (eg Look) Hambini is known for his know how on aerodynamic and BB design and manufacturing, which are the best in the bike industry.
@reginaldscot165
9 ай бұрын
That’s debatable. 😉
@yonglingng5640
9 ай бұрын
@@reginaldscot165 I thought there's no specific torque spec for top cap bolts? Isn't it just a matter of eliminating headset play without binding the bearings?
@ovesimonsen5578
9 ай бұрын
Thanks for posting. This video is shocking! Not even my winter bike, that sees both snow, rain and sweat from indoor training, have ever had corroded steerer tube bearings. The handling of this bike is pure foolish. I kinda expected he would put it down on the handlebar/saddle at some point.
@reginaldscot165
9 ай бұрын
Thank you. Yes it is shocking.
@deantranter1258
9 ай бұрын
Hambini… In the land of the blind. A one eyed man is king.
@reginaldscot165
9 ай бұрын
Very much so.
@deantranter1258
9 ай бұрын
Funny thing is I’m a mechanic, own a bike shop and ride a Cinelli Nemo Tig Gravel & a Reilly 325 titanium road bike. We are almost twins! 😂
@reginaldscot165
9 ай бұрын
@@deantranter1258Hello Brother! 😅👍🏻
@zedtony8110
9 ай бұрын
That was one of the most amateur jobs that I have ever seen. Driving the steerer tube all the way down by belting it was so wrong. All you needed to do was one or two hits to move the split ring up and then reinsert the steerer freeing the split ring allowing it to be removed by hand. Mate clean those bolts and grease them, what a hack.
@reginaldscot165
9 ай бұрын
Totally agree! 👍🏻
@doughorner5730
8 ай бұрын
We may disagree on many points but I'm definitely with you on this one Reginald, that was a first rate hack and painful for me to watch. Makes me think a lot of the bb creaks Hambini is trying to fix are something else entirely. This vid has altered my opinion of Hambini and his competence somewhat for sure.
@reginaldscot165
8 ай бұрын
And this has just scratched the surface, there is evidence to suggest he is up to much worse…
@thomasfitzgibbon1675
9 ай бұрын
I was naive enough to actually buy headset bearings from his website. They were notchy and caused creaking from the moment I installed them. Swapped them out for no name bearings off EBay and the steering felt like butter in comparison. Do not trust the vulgar hamster man!
@reginaldscot165
9 ай бұрын
That’s not good, I’d expect better from the “bearing expert.” 🤔
@sturidesbikes
9 ай бұрын
Lol Hambini is such a hack. Ps I’m a bicycle mechanic of over 30 yrs experience in the bicycle industry. Great video by the way.
@reginaldscot165
9 ай бұрын
Hack or bodge? 😆 Thanks ☺️
@sturidesbikes
9 ай бұрын
@@Trippenzoid engineers are responsible for all that is bad in cycling.
@oldiegoldie-j4h
9 ай бұрын
@@sturidesbikesReally? I'll tell you the truth, the one who responsible are _-censored-_ They're moved the bikes production to far east with slave wages and Chinese tofu level engineers for their profit and greediness.
@rainerunsinn4808
9 ай бұрын
Wow, that hurts. This shows the difference between an engineer and a mechanic.
@reginaldscot165
9 ай бұрын
I think it’s an insult to tar all engineers with this brush… all the ones I met in the robotics industry are definitely not like this. 😅
@danm3359
9 ай бұрын
I enjoy watching your and Hambini's videos. To be fair this is a fairly old video and he looks like he doesn't have a lot of experience working on bikes. Everyone has to start somewhere I guess but he should really pull these videos and do new more accurate service videos. Hindsight and being able to nitpick every wrong in this video is something of a Hambini signature imo. Which can be both good and bad.
@rainerunsinn4808
9 ай бұрын
@@reginaldscot165 I changed from being a mechanic to being a civil engineer and most of my colleagues nowadays, couldn't even mount IKEA wardrobe to save their life.
@domestickev63
9 ай бұрын
I'm no mechanic but do the basics on my bike to keep it roadworthy. I always use a torque wrench and grease threads and bearing cups etc, if my level of competence was at this level I would stop immediately. Painful to watch. I've watched quite a few Hambini videos and had my doubts about him.
@reginaldscot165
9 ай бұрын
Well you clearly have a basic grasp of how to look after your equipment. Something many people don’t understand. Safe riding 👍🏻🙂
@larryt.atcycleitalia5786
9 ай бұрын
When he starts offering his wrenching services (vs BB products) to the public, watch out. Until then, try to keep your chamois from bunching up. The fauxtrage here isn't even funny.
@lovemore4229
9 ай бұрын
Well, Reginald you seem to have exposed Hambini as a pretty sloppy bike mechanic, the level of work expected from a 5 year old and as an added bonus, you've made a pretty entertaining enemy, I can't wait for the next installment.
@reginaldscot165
9 ай бұрын
Well, at least you noticed. Some people can watch the same video and see nothing wrong. 😅
@SR-fm1ft
9 ай бұрын
Hi there, 9000 series brakes have the set screw on the front. ~really they do, both the direct mount and center mount. Also a bike mechanic, I get things wrong all the time it’s easy to do with all the different standards. Pretty certain on this one with the calipers. It’s on my bike now.
@reginaldscot165
9 ай бұрын
They do make some brake shoes with the screws in the front but only for specific frames. (For example scott foil aero bike) but if you look closely you can see that the blade that hangs off the bottom of the shoe is also pointing in the wrong direction. So this is the second bit of evidence that it’s on backwards. A quick google search will prove I’m correct. 🙂👍🏻
@reginaldscot165
9 ай бұрын
Also at 25:19 you can see that the front of the shoe is open ended. By that I mean the pad can come out the front not the back. Take a look. 🙂👍🏻
@SR-fm1ft
9 ай бұрын
@@reginaldscot165absolutely correct bang on I see it! LOL you called it, I have a Foil 🥂
@bigredcardigan
8 ай бұрын
I think the bar tape says quite a lot about his competence
@reginaldscot165
8 ай бұрын
I think it’s just old, looks like the original factory tape. 🤷🏻♂️
@kindjalkazad
9 ай бұрын
From what I saw from Hambini over the past few years...he looks like a really good engineer...but that's all. He know how to really design good stuff, he know how to manufacture things...but being a good mechanic is another thing. And that's not because you are a good(or even a perfect) engineers, that you are a good mechanic. You could, but usually, it's rarely the case.
@sixy69
9 ай бұрын
A good engineer does not make a good mechanic. This video proves that.
@reginaldscot165
9 ай бұрын
Well, looks can be deceptive… I know plenty of engineers who are good with their hands. But maybe it’s just my previous industry? 🤷🏻♂️🙂
@sixy69
9 ай бұрын
I was too lazy for all the calculations when I was studying to be an engineer. So I dropped out and stuck to mechanics.@@reginaldscot165
@kindjalkazad
9 ай бұрын
@@reginaldscot165 maybe :) Because in mine(radiation safety) it’s definitely not the case ^^ And I’d say also, it clearly depends on of the type of engineer also. If it’s a « computer/paper engineer » there is good chance he is a bad mechanic. If it’s a broader type of engineer, you can find one that is a good mechanic :) This comes from my personal experience, as an engineer, and working with engineers
@joshiek7839
9 ай бұрын
I wouldn’t call Reggie good mechanic. In fact calling him a mechanic is a big stretch
Пікірлер: 434