Thank you very much, my GR-20 stop working for unknown reason. I follow you advise and the machine is working now!!! hooray!!!! save me time and $$$
@Zach-f5m
Ай бұрын
People if you want to get the point, FF to 1:50. Thank you
@Louis21237
8 ай бұрын
Thank you This helped me fix a 2632
@reniecarrizales1553
Жыл бұрын
For awhile there were a bad batch of contactors that were coming out but now their past that... Dead give away do you hear it click it not check for 24 volts at the contactor and if you do have 24 volts then check the resistance of the contactor it could show an open or direct short across the coil...
@DieselPower505
2 жыл бұрын
Jlg and Skyjack would call it a line contactor at I could see where it could be a pain if it was failing intermittently. Jlg Es scissors will at least give you a fault code and they usually just go bad and thats it. Good to know for these genies.
@avilaagustin1
2 жыл бұрын
I know JLG usually tell you a code Genies do too but jlg seems a bit eaair as of getting codes
@mh1art870
Жыл бұрын
Thank you dude!!!!!!
@barneycarparts
2 жыл бұрын
clicky relay no worky Clean contacts with emry paper or get a closed sealed relay maybe. I have same no go thing with a GS-1930 lift. Relay clicks no go. Last time it was the motor controller.
@avilaagustin1
2 жыл бұрын
Another issue with the genie scissor lifts are alot of dust or debri in the pump itself. If relay clicks and still doesnt move, open the side door where the hyd oil goes, and behind it you will see the pump, smack it while moving joystick and see what happens, also rn some compressed air in it. For some reason its really easy for it to stop it. Its well worth it
@asylumsys
Ай бұрын
I got one that won’t go up with load what might that be
@forkliftiq
Жыл бұрын
Thanks for your help
@glenclark3615
10 күн бұрын
I wish you actually tapped to show us how it works.
@williamsmith8760
11 ай бұрын
I have awp30s and 25s mine reads 6 ohms on both 10v coils. One motor starter coil clicks multiple times likes its slapping, that one is 3 ohms to ground. The other just buzzes and its 6 ohms to ground. Both batteries are weak so the test is while pugged in. Could the starter coils be bad on both?
@jrclark32
6 ай бұрын
My GS-1930 started doing this. Batts are fully charged, but when I try any function it just beeps and doesn’t do anything. I tried tapping the solenoid, but that didn’t help. Does anybody have a suggestion where to go from there?
@MrJmacharia
Жыл бұрын
I have a genie 2632 with the same issue (lift, Steer and drive function not working, alarm going and codes all on) but that solenoid is not there…kindly assist
@robertgarcia-zn7ed
Жыл бұрын
Dc contractor 24v 100a
@HanifEFIMechanical
2 жыл бұрын
Good
@AB-yu2tj
2 жыл бұрын
Thank you. I have a problem with a Genie IWP'-25 I was hoping to get working. Problem Is that it does not stay up. Keeps going down. It started slow with a couple of times going up then it would go down but then it got really bad really fast. Would you happen to know where and what could be causing it.
@barneycarparts
2 жыл бұрын
Its prolly a leaky hydrolic piston seal in the lift cylendar. I have leaky ones in my Kubota. Take the lift up put up the safety bar try and read the number on the cylendar collar. buy a new seal kit. To put it on takes about 2 hrs RnR, or take the cylendar into a parts house they can look at it and tell you which kit to buy. Its usually 3 O rings. Abt $13-23
@avilaagustin1
2 жыл бұрын
Check your check valves for the cylinder thats leaking down. Safely remove the check valve, just make sure the machine is down. Then clean it real well and most of the time that fixes the issue, ir might just need a new one.
@Hiperf
2 жыл бұрын
Could this still be a problem if the platform controls with still lift and lower the lift? When switched to platform controls, nothing happens though.
@avilaagustin1
2 жыл бұрын
Not really with this issue, when you switch it do you get anything at all? Does the little green screen come up? The alarm maybe or does it not do anything at all?
@Hiperf
2 жыл бұрын
@@avilaagustin1 Function switch on the joystick was bad. Found the same wire half broke all the way down. Changed the joystick. Back to working again.
@Dacrocom
Жыл бұрын
I have had this for a week and I can’t figure out how that fuck to lift it!
@georgescott6049
7 ай бұрын
Is this same as the H067 code H067:FAULT MC ENABLE bat
Пікірлер: 25