you can use the studs a second and third times by slightly bending the tip to 90º, Nice video thanks for your time!
@jamieround2072
3 жыл бұрын
so what's the name of that lil T handle pulling toll.... & from where.... & how much was it if u member ...... cus it seem's to hold onto the weld'd stud a bit better & more securely too not so easy of it to let go like the harbor freight one u said was junk............... i can see why here ......
@jma8352
Жыл бұрын
i see whare a guy welded small vice grips to the slide hammer, im gona try that
@WRATHUSA
5 жыл бұрын
Why clip the studs off prematurely before the sheet metal has been completely regulated back into position? It seems that you may need to go back and forth until the pressure is released.
@peterrivney552
2 жыл бұрын
True also wondering why he didn't show the what you got with the kit ... Like we know it not a professional system but it does the job myself I have an old Porta spot system with all the different tips as well as stud and washer and use that to pull out dents...
@djm9937
2 жыл бұрын
The label on the stud welder describes it as a stud wedler
@gregorykadok3356
5 жыл бұрын
what kind of studs are you using? The one's that come with Harbor Freight don't stick
@trillionbtamillion
4 жыл бұрын
😠
@Parsa012008
5 жыл бұрын
Hi there is that working on thick metal plate also form 10mm to 15 mm ? or only work on thin panel ?
@omni875
6 жыл бұрын
just bought and used the harbor freight stud welder this weekend. only issue was the large studs would not stick, but the smaller ones worked great. everyone complains about the slide hammer, but I thought it worked great, I didnt have any isses with it, pull out, then a slight tap back toward the car and it released, and if the stud broke loose, i just tapped the stud on the ground to get it to release. Might be good idea to wear safety glasses when welding or snipping metal.
@wickedspray7475
6 жыл бұрын
The slide hammer I had worked alright at first but then the teeth on the wheel started wearing down and wouldn't hold the stud.
@Anunnakey
5 жыл бұрын
Hi, I like the little puller you're using, where can I get those from?
@wickedspray7475
5 жыл бұрын
It came with the stud welder kit. You can buy it on amazon, Ebay or most autobody supply stores. I think it's called a t-handle stud puller.
@raywilson7797
5 жыл бұрын
Where can i get the t handle
@hillbillypaintballin
6 жыл бұрын
I needed one of those now long ago and think I need one now ..i'm just always hesitant about nay body work lol
@wickedspray7475
6 жыл бұрын
The welder works good, just the puller that comes with it sucks. I"m thinking about doing a better review on it in the next couple weeks and giving info on where to buy a better puller for cheap.
@Greaner762
5 жыл бұрын
Is that a corrado?
@Venom_Dvbz
6 жыл бұрын
Hey what power cord should I buy to use this ?
@aeugenemartin
6 жыл бұрын
Venoms_Cards you should get at least a 12 gauge extension cord
@robertv8851
5 жыл бұрын
There's copper transformer in it.
@3500camarz
Жыл бұрын
You cover your car and your face from all that sanding, but fail to cover your lungs. People, I strongly advise to wear a respirator when sanding and especially when welding. At the very minimum wear a paper mask.
Пікірлер: 21