If my college project gets complete it's because of this video..... Thank You for heavy load drivers...
@robojax
3 жыл бұрын
Happy to help
@justlife2129
4 жыл бұрын
It is an art to explain some complicated things THE EASY WAY. Thanks!!!
@robojax
4 жыл бұрын
You are welcome. I am glad you found them useful. The best thank you for me is to Subscribe 🔔 to my channel and thumb up the video. It is greatly appreciated. 🔔 😊.
@solosailorsv8065
6 ай бұрын
Very good details and demonstration, thx. As a "Switch" use, turn it ON with 4.5v for the automotive 10.5v thru 15v range with a thermistor monitoring the Fet temperature, steady state at 70f (120f for Arizona) ambient for at least an hour.... Although for a common ground automotive use, a P-Channel high side mosfet is more practical....
@MiljanBojovic
6 ай бұрын
Finally someone who explains it in details! Thank you! :D
@robojax
6 ай бұрын
Glad it was helpful!
@taylerallen7841
4 жыл бұрын
THANK YOU! It has been extremely hard to fine a good explanation of these and your video summed it up quite well.
@robojax
4 жыл бұрын
You are welcome. You haven't subscribed to my channel. The best thank you for me is to subscribe to my channel and thumb up the video. It is greatly appreciated. 🔔 😊
@englishrupe01
3 жыл бұрын
An excellent demonstration of all the facets of this tool! Thanks for sharing your knowledge, Ahmad!
@robojax
3 жыл бұрын
Thanks for watching
@honda9731
4 жыл бұрын
Thanks a bunch Robojax, in return for your good presentations, I don't skip ads even in your other videos as gratitude
@robojax
4 жыл бұрын
You are welcome. Thanks for your support.
@waldguy
6 ай бұрын
VERY nice video and explanation. Thumbs up!! I had a strange situation with mine. When I used Ground from my board (24V, stepped down to 5V with 7805), the module failed to work! Yet, when I just used the gate PWM signal, with NO ground attached to the small voltage connections, it works! I'm not very experienced so I'm probably doing something wrong!
@RalphWLundvall
Жыл бұрын
Excellent overview. Many solderable inputs are no longer confusing. Good job.
@StarJar58
5 ай бұрын
Wow, excellent, thanks. And your English is so good!
@robojax
5 ай бұрын
Thank you too!
@federicopinto5053
5 жыл бұрын
Thank you! Good video! The only things is that you don't really need a diode in antiparalell since the mosfet has one incorporated. As long as you don't go over 20 amps you are fine. Acording to the datasheet
@robojax
5 жыл бұрын
You are welcome. That is a good point I ponder upon. Thanks for the tip.
@homevalueglass3809
4 жыл бұрын
Thanks dude
@surenderkumar-yi1ig
Ай бұрын
Very useful video sir
@aliors3433
4 жыл бұрын
I wld really like to thx to u Mr. ... cuz when ever I want to curious some item about electromechanics, you Sir on the line which gives sufficient/above (such as gives:... ooohhh I got it [what else :) ] information/data. I felt to give furthermore-thx so plz keep go on..! U r u in a business to give big support which help ppl like me who else doesn't know really anything about the core subject of this comment..!
@robojax
4 жыл бұрын
you are welcome. I am glad you found it useful.
@daveolson9504
4 жыл бұрын
Thanks you do such a great job explaining as well as showing!
@robojax
4 жыл бұрын
You are welcome. Thank you for not skipping the ads and keep watching them. This will help me a lot.
@chrisnothnagel4910
3 жыл бұрын
Excellent video. This is how it must be made. TX 4 sharing
@robojax
3 жыл бұрын
Glad you enjoyed it! Please subscribe. It is appreciated.
@jonnupe1645
2 жыл бұрын
Thank you for sharing in this detail
@yukselle.
3 жыл бұрын
Hello sir, I loved how you are good at teaching. I have the same module. I am designing a buck converter and when I connected this module to my circuit. It didn’t work. What should I do ? It works when I connected a small resistor to the module but when I connect it to the a converter, it didn’t work. HOW COULD I CONTROL THE MOSFET ? PLEASE HELP ME ! Thank you and stay safe 🙏🙏🙏
@damianm1030
3 ай бұрын
Hello. Nice explain. Thx. But, why when in serial monitor motor speed is 0, motor still turn, or lamp still glow? Why voltage go not to 0V? Thx for explain
@LuisDiaz-of1ez
3 ай бұрын
Hi, just suscribed to your channel. Quick question: If I want bidirectional control on the motor, how could I achieve it using the HW-517 module? Thanks!
@jarrellestes1793
3 жыл бұрын
Great video
@robojax
3 жыл бұрын
You are welcome. Here is $200 Arduino course for free Arduino Step by Step Course (over 100 lectures) Starts here robojax.com/L/?id=338
@dennisbohansen5408
5 жыл бұрын
Really informative presentsation - Thanks a lot
@robojax
5 жыл бұрын
You are welcome.
@iordanjelqzkov3337
4 жыл бұрын
0
@pisoiorfan
9 ай бұрын
Since the two are in paralel the D-S resistance is double for each MOSFET
@tonyb5469
6 жыл бұрын
Very nice, just want I wanted. I am looking to control a 70w (12v) pump, so I think this will be perfect.
@spudnickuk
2 жыл бұрын
Thank you for a good video of this module. i went and bought some. But i Do find they get extremely hot. I'm using a 11.1 lipo battery at 2000Ah I'm using it for a small engine and so the Mosfet is being used for the ignition coil So I have the Mosfet connected from the Arduino and is connected with the Lypo 11.1 and the mosfet is connected to a Ignition Coil that has a spark plug that generates the Spark But after 5 seconds it gets extremely hot but other devices don.t get hot. so the coil is drawing to much i dont know what i can do apart from adding some heat sink but i do think it can be sorted via another way but don't know Any help from any one I will be very grateful
@andrewburke8238
Жыл бұрын
Good stuff man
@albertramirez-rb1io
3 ай бұрын
Can I use potentiometer to drive the gate of the mosfet? Thanks for the video.
@DRZME400
2 жыл бұрын
great video!
@youssefdirani
5 жыл бұрын
The Rigol visual interface is very interesting, can you tell us more about it in a separate video... I mean the hardware equipment and so.
@robojax
5 жыл бұрын
Hopefully if I find time. I have it on my list to do a review of the Rigol Electronic load.
@sgafaroff
Жыл бұрын
@robojax Thanks for the cool video. I'm a beginner and don't really understand such subtleties. Please tell me, can I connect a solenoid as a load and control it? And also if the solenoid winding suddenly burns out and a short circuit occurs, what will happen to this module?
@Skagenin
4 жыл бұрын
as usual. an excellent video :-)
@robojax
4 жыл бұрын
Glad you enjoyed it
@DaveFer
Жыл бұрын
Thank you for making this video. It's great. Quick question: What about reversing the motor? Does this motor driver support reversal?
@DaveGrennan
Жыл бұрын
Not by default, you could use multiple modules to make a full bridge. I think robojax has a video for that.
@sunnydaybadua2868
4 ай бұрын
Hello Robojax, I am very glad that I found this video of yours. I would like to to use this board to do 2s vape mod. I am quite concerned with the Rds(on). It is too high for the my application. the mosfets will heat up quite a lot for 20 - 30A amplication. Will it be possible to replace the mosfets with IRBL 3034? If so, will I still be able to control them using PWM? Thank you!
@robojax
4 ай бұрын
Hi, upon checking the specs of suggested mosfet it seems the IRLB should work. Both have VGS=20V and others specs should not matter in this application.
@sunnydaybadua2868
4 ай бұрын
@@robojax Wow! I wasnt expecting a response from you this quick. Thank you so much, Robojax!
@yogeshitaliya473
6 жыл бұрын
Nice one sir
@robojax
4 жыл бұрын
Thanks.
@sozluk
Жыл бұрын
Wow, perfect video, covering a lot! One question, at 12:45 you say you can change polarity with 4 of those. Would you explain how please?
@robojax
Жыл бұрын
Thanks. that needs full separate video.
@rongyos
Жыл бұрын
Hi sir, excellent tutorial? Can I use this module to maximize the voltage from an esc? I mean without that the motor reaches the max speed 7.2v but when I push a button on arduino it lowers the maximum voltage to 4v for example. The main issue I see here is the change of polarity (to go backwards with my device) can you suggest something for a bidirectional regulator where the vin is came crom an esc?
@Enoch-Gnosis
3 жыл бұрын
Can you please explain how to connect a frequency generator module to the XLX? Thank you
@robojax
3 жыл бұрын
What is XLX?
@Enoch-Gnosis
3 жыл бұрын
@@robojax www.amazon.com/XLX-Transistor-Module-PWM-Regulator-Electronic-Switch-Controller/dp/B07ZHC5M7H I’m trying to build a PEMF device using a Frequency Generator Module = XLX Mosfet Module = Out To Coil any advice on how to hook it up ? Thank you
@robojax
3 жыл бұрын
this is the same module. they just call it like that. I have no idea what kind of coil you use. I tested it so you know the maximum current. Remember if you use coil when the signal turns OFF, the energy with revers polarity from the coil is might kill the module.
@RIKOARIshowreel
3 жыл бұрын
If I use 10S Li-ion battery power supply (36v), which when fully charged ranged mostly at 42v, will it blow the mosfets? This was great channel btw, just subscribed!
@robojax
3 жыл бұрын
Thanks. I've shown the datasheet and I just checked it. 40V is the "Absolute maximum" meaning it blow anything above 40V. However you can replaced the mosfets with IRFZ44N. See datasheet for IRFZ44n here www.vishay.com/docs/91291/91291.pdf
@RIKOARIshowreel
3 жыл бұрын
@@robojax cool, thanks for the advice, appreciate that. 🙏🏻
@kevinrehak3035
Жыл бұрын
This video is super helpful! Question: I’m using a 12v lead acid battery, to control a DC motor. I’ve burned up 3 of these MOSFET modules. Do I need a resistor somewhere?
@robojax
Жыл бұрын
Hello, the battery voltage won't kill it. it is the amount of current (or power) that kills it when it is above the limit. See this module different version of this which is much better kzitem.info/news/bejne/xqeOx6WIf3OIpXY and there is resource page link to purchase it.
@tanoryjakaperdana1419
Жыл бұрын
The trigger, how much voltage can it receive?
@ujang0711
2 ай бұрын
Do you have the answer already?
@DaveGrennan
Жыл бұрын
Hi Robojax. Thanks for a great vid. Could you use 2 or more of these modules in parallel to switch higher current or to keep the modules cooler when switching around 400W?
@robojax
Жыл бұрын
Yes you can .
@DaveGrennan
Жыл бұрын
@@robojax I bought a few of these and I'm putting a 350W resistive load through just one and it hardly even gets warm 🙂
@techyogihub
5 жыл бұрын
This is so cool. I really need a help here. I want to change the polarity as well. Using a 12V-3A motor. Is there an h-bridge module of the same mosfet or should we make it by our self ? Or can you recommend another single channel h-bridge motor driver which is not very expensive. Thank you.. Cheers.
@robojax
5 жыл бұрын
You are welcome. The mosfet have been used in chip to control motor but with 1A or 2A. There is L298N that can handle up to 4A www.sparkfun.com/datasheets/Robotics/L298_H_Bridge.pdf and module is sold on eBay or AliExpress and Amazon.
@chisomodimmegwa3479
3 жыл бұрын
Hello Sir can I use this for esp32 cam tank robot. I feel the wheel are very slow and sometimes unresponsive. Im using the l293d bridge motor drive. Not sure if it's d battery or not. Will the Mosfet help utilise the battery more and also make the wheel faster and more responsive?
@MBaitullahAlAmin
4 ай бұрын
Hi Mr. Shamshiri, I want to use this module to control the speed of DC Pump 12V with the current 5A. I know from your video demo, that the module should be ok and can handle it. But I want to know further, if I use it for continuous current (5A) in SIX HOURS of an operational pump (without stopping), will the module still work well? I mean what about its temperature? Or can you give another recommended module for that purpose? Your suggestion would be helpful. Thank you.
@robojax
4 ай бұрын
salam alaikum, of coruse it can . 40A is continouse current at 100C and and 50A at 25C don't every trust free talk. Look at datasheet www.aosmd.com/sites/default/files/res/datasheets/AOI4184.pdf
@MBaitullahAlAmin
4 ай бұрын
@@robojax Wa'alaikumsalam. Thank you for your response. I'll go to try this module. One more question Sir, if you may. What size of the diode used in this video demo? 10A?
@robojax
4 ай бұрын
Yes 10A.
@MBaitullahAlAmin
4 ай бұрын
@@robojax Thank you Sir. May Allah Azza Wa Jalla bless you always.
@nkofr
3 жыл бұрын
nice. Do you need an arduino or can you just use apply a DC voltage from a battery to trigger the switch?
@robojax
3 жыл бұрын
Yo switch you just need supply at input. But if you want to control the speed u need arduino. Must watch got all answers.
@mateuszmazur1980
3 жыл бұрын
Hello. Very good explanation! Good job sir! One question. You mentioned in your video that, if we have four of them we cloud control the direction of DC motor. But how to achieve that? As far as I check the VIN(in, out) is not controlled by MOSFETs only ground line is. So how to using four circuits like this address the direction of motor? Thanks in advance!
@robojax
3 жыл бұрын
Hello and welcome. that is called full bridge. please watch this video to learn about it. kzitem.info/news/bejne/sYuCm3iQcoZyZaQ
@mateuszmazur1980
3 жыл бұрын
@@robojax Thank you. Two more questions. First one about this module. Is it safe to put + (hot) wire to negative pole? To control + rather than ground connection? Is it safe for Source and Drain? Second one: I'm familiar with H-Bridge concept but in this solution we must use two "P" and two "N" MOSFETs. Here we have only one type of mosfet. How to achieve H-bridge using four of this?
@iordanjelqzkov3337
3 жыл бұрын
Can this module be used in the car to run up converter 12 to 30 volt. The controller to take a signal from remotecontrol pleyar 12 volt. The idea is to embed up converter 12 to 30 volt + TDA7498E. The controller should start up converter
@jimbrown5726
2 жыл бұрын
I AM WORKING ON A PROJECT AND NEED YOUR HELP. I have a ZK-12KXV3 voltage regulator, a ZK-PP2K PWM and a X0029KL I DD Cycle Delay Drive Module. I am not sure how to wire the PWM to the driver to pulse a pancake coil. Can you help?
@mikewalton7615
4 жыл бұрын
Your videos are very informative. I watched your video on the E-switch. Does this module have an optocoupler like the E-switch?
@robojax
4 жыл бұрын
Thank you Mike. I am glad you found them useful. No it doesn't have optocoupler.
@roadintersection
4 жыл бұрын
May I ask you a novice question, Sir? Is is alright to connect the (-) pole V- to the (-) of the load (out) such as motorcycle headlight? I'm going to use it in the motorcycle and all negative pole is connected. Thank you..
@robojax
4 жыл бұрын
I had to watch the video to answer your question as it seems you've skipped the video. please watch from 8:45 (click on this 8:45) and you should know. your motor cycle light is a load. just see how to connect a load.
@Fredhobby
4 жыл бұрын
hi again, how could we connect the RC receiver to the PWM and control it? I did that and it's not working, I've tried, and I get only 0.8V when input from the receiver is 5V, I've connected the PWM to the white signal wire, am I'm doing something wrong? thank you please help. thanks
@robojax
4 жыл бұрын
the receiver always outputs 5V. So I do'n how you measure it. This module can be easily with RC receiver.
@Fredhobby
4 жыл бұрын
@@robojax thanks for the reply, yes the receiver has 5V, I feed the input with 5V, to the PWM on the board I connect the signal white wire, and then the output is only 0.8V, do I need to connect any resister to the PWM? how to make it work? your responses will be highly appreciated...
@Abimanyu481
3 жыл бұрын
hello, i want to ask about this mosfet, is this mosfet can hold this? thankyou Current 2A Voltage: 12V DC Initial suction: 20 (N) Working voltage: 24V
@robojax
3 жыл бұрын
I have provided the link to the data sheet. Check that
@Silverblade416
Жыл бұрын
I'm just curious. . . Can this module be used on an AEG airsoft?
@Fredhobby
4 жыл бұрын
thank you for the video, could we connect the RC receiver to the PWM and control it? thanks
@robojax
4 жыл бұрын
Yes you can!
@Fredhobby
4 жыл бұрын
@@robojax thanks for the quick replay mate, I've tried, and I get only 0.8V when input from the receiver is 5V, I've connected the PWM to the white signal wire, am I'm doing somthing wrong? thank you
@Fredhobby
4 жыл бұрын
@@robojax ?
@leonamor8662
Жыл бұрын
Can you put 2 of these in parallel to control a 60A charge ?
@robojax
Жыл бұрын
yes you can
@nathanbunten4299
Жыл бұрын
You should hack 2 of these and make it into a tesla coil oscillator switch. The mofsets in these wont blow all day like the slayer exciter circuit does.
@anjarwicaksono229
2 жыл бұрын
I check my duty cycle at the output keeps at nearly 100% regardless the input pwm duty cycle
@EricRobb
3 жыл бұрын
Hello, would I be about to hook this up directly to an rc reciever?
@robojax
3 жыл бұрын
Hello, no you can’t . This module needs clean PWM while the receiver has encoded different signal. I have not tested it but it will have unusual behaviour if you connect it. Try it. There is no harm.
@hamzaarshad861
4 жыл бұрын
Hi Robojax ..Tell me if I am wrong but does 2 mosfets mean that this board has bidirectional control. if not why is there 2 mosfets? … also is there a circuit diagram for this board
@robojax
4 жыл бұрын
Hi, perhaps you skipped the video. I just watched the video and I have explained it. I can't type everything there. Watch the video fully and you will get the answer.
@DocMicha
4 жыл бұрын
Hi good explanation. I wonder if this device works really also at 3.3 V Vgs as they say .
@robojax
4 жыл бұрын
Hi, Thanks. I have not tested it but it should work.
@vladbeniaminbruma3108
3 жыл бұрын
can it run at 12V 1.5A constantly without a heat sink?
@waldguy
6 ай бұрын
I can run a 24V 2A motor without a heat sink.
@sandeepthorvat6395
4 жыл бұрын
hi sir witch one is good MOSFET for switching AOD4184A or IRFR5305 also support for more voltage & ampere.
@robojax
4 жыл бұрын
Hi, AOD4184A can handle Drain current 50A/40A at DS voltage of 40V and datasheet here www.aosmd.com/pdfs/datasheet/AOD4184A.pdf and IRFR5305 can handle -22A continuously DS Voltage of -55V See datasheet here www.infineon.com/dgdl/irfr5305pbf.pdf?fileId=5546d462533600a401535632522820ff and you will find the answer to all of your questions. Good luck
@mikefriesdrums
Жыл бұрын
Can I use a potentiometer to vary the trigger voltage and thus proportionately vary the output voltage to the load? I am just a beginner skill level with electronics. Thanks
@robojax
Жыл бұрын
No you can't. this a switch. either will turn ON or OFF. if you want to control a load, then use PWM like controlling the brightness of LED or speed of a motor you can very easily control the speed without changing the voltage. It is better and effecient. load is not controlled by verying the voltage.
@mikefriesdrums
Жыл бұрын
@@robojax Thanks, this makes sense now that I think about it.
@donichannel3579
Жыл бұрын
What motor dc do you use
@maiorciprian
Жыл бұрын
Will the Mosfet be fully turned on when the trigger signal is only 3.3v?
@robojax
Жыл бұрын
I believe I have provided the datasheet in resources page. Look at it there should be table and graph.
@marianodiaz461
2 жыл бұрын
hi; at 12:46 looks like that the pwm input are wired into the 2 far side out pins? I have wired the two PWM terminal to the big J1 connector holes , the LED lights up but the motor is not turning , this motor used to work with the other controller ( the one with the pot included ,that you have show us in another chapter) ,can you please suggest what can be wrong? thank you
@robojax
2 жыл бұрын
We have power that comes to the mosfet. Then we have PWM signal that turns on or off the power. So you have to connect the power.
@marianodiaz461
2 жыл бұрын
@@robojax yes I tried it outside and works, must have been a bad connection, thank you for the advice
@jarrellestes1793
3 жыл бұрын
Looking at a constant current. For. Solar battery to feed inverter
@chasidgoodmaker1804
2 жыл бұрын
Hello I want to see a circuit of this Mosfet trigger switch drive Please if u have it show me It’s very important for our project We r making the electronic device with pwm input signals and we need a higher power of this signals that’s why pwm amplifier needed Thanks appreciate it
@robojax
2 жыл бұрын
Hello, please contact me via robojax.com contact page and provide your email in the body of your text. I will contact you and collect the details then I will tell you the cost, write the code, make demo video and you pay only if you are satisfied with the demonstration video.
@fadelfarae6019
2 жыл бұрын
Can I use two of those to control motor in Forward and reverse.
@robojax
2 жыл бұрын
No. If you don’t need to control the speed then relay could be used. Search my channel I have video on that.
@sandeepdk8653
4 жыл бұрын
Sir i have to use this for 4 solenoids interface with arduino but this solenoids are operate one by one so I have to use solid state relay to fast switching operation so have to use this solid state relay so how many times this will be a off ,on in 1minute or 1 second
@robojax
3 жыл бұрын
yes you can use two of this to connect.
@prakhartripathi8567
3 жыл бұрын
I am controlling motors with raspberry pi 3model B using relays but when operating other small sensors connected to raspberry pi i2c ports stopped working. Can you explain why this is happening?
@robojax
3 жыл бұрын
I have not tested this with raspberry pi
@adrianTNT
4 жыл бұрын
Could this act as a led driver and provide power for ~30V ~40W led ? (With a ~36V power source). Thanks.
@robojax
4 жыл бұрын
I have explained it. Watch this with more power kzitem.info/news/bejne/qG-rroqZgoZ5mW0
@sandeepdk8653
4 жыл бұрын
Sir please tell me switching rate of this module that means this will be how many times off and on in one minute?or 1 second
@robojax
4 жыл бұрын
it is in the delay() and if you want it faster, I have provided the datasheet. See it.
@ourchannel8215
3 жыл бұрын
this mosfet good for 12v or 24v inverter?? small cute and good for high amp
@robojax
3 жыл бұрын
I believe I mentioned the voltage in the video. I don't remember.
@justlife2129
4 жыл бұрын
Can you connect more MOSFETs in parallel in order to get more current?
@robojax
4 жыл бұрын
yes you can. If you use heatsink as I mentioned (I believe I mentioned ) you will have 2 or 3 times current than without heatsink.
@nguyenthuy9824
3 жыл бұрын
Hi. Thanks so much and dear sir. This module is only CW (clockwise) function, no has CCW (counterclockwise) function. I want to use module has two functions (CW, CCW) So I would like to know what's kind of it (my motors: max current 10A, 12VDC). Note: I have been using BTS7960 for controlling my motors with arduino. But because of expensive. I'm not programmer, architerth, coder. I'm waiting inf form you. Thanks
@robojax
3 жыл бұрын
see this L298N kzitem.info/news/bejne/2KRrqmugaquTq44
@nguyenthuy9824
3 жыл бұрын
@@robojax Thanks sir reply. Yes off course L298N has two 2 functions (CW and CCW), But L298N module has max current 2A. I can not use L298N because my motors (7A - 10A).
@robojax
3 жыл бұрын
search for the word PWM and you will see more than 10 videos and modules with very higher current.
@nguyenthuy9824
3 жыл бұрын
@@robojax Honesty, After you reply. Sundden idea in my mind, and it's done well. Thanks you
@hassanmasood2935
3 жыл бұрын
sir can i use this module as simple ON and OFF control for 12v , 12.3amp dc fan heater?...
@robojax
3 жыл бұрын
Yes you can.
@isacdaimary9908
2 жыл бұрын
Can we use this MOSFET as HIGH SIDE switch ?? Please reply
@robojax
2 жыл бұрын
no you can't . on the high side, the Gate voltage needs be higher the source pin. when you have load of 12V on the source, then gate needs 12V+GSv, if GSv=5V, then you need 12V+5V=17V. for that reason you need gate driver chip which will take care of this for you.
@darmakiss4829
Жыл бұрын
hello everyone....i need it for 105vdc i'm afraid if i use it like that it may burn ...any suggestion thanks ?
@robojax
Жыл бұрын
Here is the the better option kzitem.info/news/bejne/xqeOx6WIf3OIpXY
@carstv1355
Жыл бұрын
Does this module can be use for solar light led light 1100 lumens?
@robojax
Жыл бұрын
to find the rate of an electronic switch like this, usually the current in Ampere is important then the voltage. I assume the voltage is low and the current for 1100 lumen is very low. this device can handle 15A and if voltage is 12V, then it would be like 180W and I am sure your 1100 lumens less than 50W. Check the information and if the current is less than 15A you can use it.
@tvarsivi100
4 жыл бұрын
Can I also use this module for LED drivers, I have led strip 12 v 15A, my power supply is 12V, 20 A, I want to dim the LED strip
@robojax
4 жыл бұрын
yes you can. LED strip and motor can be controlled the same way. Can you please post a new comment and tell me what kind of LED strip you have that needs such power? I don't understand why even people need to use LED strips. I have one at home in our kitchen which needs only 2A or 3A. I want to know and make video on that. Thanks.
@ocdtechtalk
4 жыл бұрын
@@robojax I am using to drive LED strip as well. My LED strip uses 12vdc at 2.6W per foot. I have 16 feet in one cabinet. If I open all 3 cabinets I have a little over 10A.
@dendot81
5 жыл бұрын
Nice sir, can i use this for thermoelectric/peltier load?
@robojax
5 жыл бұрын
Thank you. yes you can.
@nuggetczsk
4 жыл бұрын
You can but efficiency will be reduced
@hanskristian5909
5 жыл бұрын
Sir, i wanna ask. I use the same mosfet and arduino uno. I'm trying to dim my lamp using the mosfet and LDR. The problem is only the mosfet get dimmed not the lamp. The lamp is still on while the mosfet got turned off. Am i doing it wrong? Thank you
@robojax
5 жыл бұрын
What kind of lamp is it? You can use only DC bulb or DC LED light. Not AC household bulbs. If the mosfet turn OFF, your light should turn OFF. So you are doing something wrong.
@hanskristian5909
5 жыл бұрын
@@robojax oh i see. Yes i am using an AC lamp. I'm still kinda new on this stuff and is doing a project about adaptive lamp. Thank you for your help!
@robojax
5 жыл бұрын
You are welcome.
@vishnumabeer6772
3 ай бұрын
Please explain how to create an h bridge or reverse the direction of motor using MOSFET trigger switch. You can PM me
@youssefdirani
5 жыл бұрын
Thanks In 5:11 Vds max is 40V when Vgs is assumed to be 0 ?
@robojax
5 жыл бұрын
You are welcome. Gate-Source voltage is your source voltage to the motor. VGS turn ON and OFF with PWM between 0 and 5V.
@youssefdirani
5 жыл бұрын
And what does 40V Vds mean?
@drzacks
3 жыл бұрын
Is it okay if I add external diode between Vout+ and Vin+ in this module? Thanks
@robojax
3 жыл бұрын
yes you can.
@drzacks
3 жыл бұрын
@@robojax Thanks for the reply and helpful. I just started learning some arduino stuffs. I am sorry for typing mistake, what I meant was external diode between Vout+ and Vout-, not between Vout+ and Vin+.
@robojax
3 жыл бұрын
You can edit comment at any time. just click on the 3 dots. between output pins that goes to the mosfet.
@nuggetczsk
4 жыл бұрын
It is possible to change the direction of rotation of the motor?
@robojax
4 жыл бұрын
no. this is half bridge. you need full bridge. Here learn about Half and Full bridge kzitem.info/news/bejne/2KRrqmugaquTq44m40s
@nuggetczsk
4 жыл бұрын
Can i use DRV8833 Motor Driver ? a.aliexpress.com/_dWgC5TJ
@robojax
4 жыл бұрын
Yes this is full bridge and you can control motor in both direction.
@tahsinurrahim1700
3 жыл бұрын
Can i use this to drive a Line output transformer?
@robojax
3 жыл бұрын
this can feed DC current to a device with the current I tested. so it is up to you.
@nuzhatnaz2157
4 жыл бұрын
i have tried using same module to control motors ,as i increase load on motors ,it draws current around 3-4 amp and mosfet starts warming up ,i looked into data sheet it says Id is 50amp(Maximum) ? HELP me with THIS ISSUE ... thanks
@robojax
4 жыл бұрын
Hi, when you said " looked into data sheet it says Id is 50amp" it show you have skipped the video as I have explained this. Please watch without skipping .
@nuzhatnaz2157
4 жыл бұрын
@@robojax ok
@iordanjelqzkov3337
4 жыл бұрын
Can it be used for an upstream car converter to run from a cassette recorder remote 12 volt out
@robojax
4 жыл бұрын
I believe the test I presented show give you the answer.
@iordanjelqzkov3337
4 жыл бұрын
@@robojax Pioneer remote control 12 volt make a circuit and put the module in the car and start the module up conwertor 12-14,2volt 15 amper to 24 volt 7Amper max amper. I think it will be thanks a lot for the video.
@robojax
4 жыл бұрын
the reason I said that , I don't remember what happened in the video and in order to answer your question, I would have to watch the video and answer. So I suggested that you watch it. You can come to conclusion by looking at Maximum Current I have tested.
@brendencarvalho
5 жыл бұрын
Can I use ESP8266 with 3.3v logic also? Instead of arduino
@robojax
5 жыл бұрын
Yes you can. I have provided the link to the datasheet in the description and the threshold voltage is 2.6V and it should work. Here is the link once again www.aosmd.com/pdfs/datasheet/AOD4184A.pdf
@jaweriashsik1287
8 ай бұрын
Yet p type h ya n type mosfet module
@robojax
8 ай бұрын
it happens.
@anjarwicaksono229
2 жыл бұрын
pwm 50% duty cycle on me doesn't give me 50% of voltage input.. how could that be?
@robojax
2 жыл бұрын
May be you have waring understanding of PWM. It is not redesign voltage at all. Voltage must stay constant.
@anjarwicaksono229
2 жыл бұрын
@@robojax Okay your statement i totally correct. I forgot to mention that I add capacitor at the output an alas the voltage doesn't give me 50% of voltage input
@youssefdirani
5 жыл бұрын
I guess the motor supply ground is the same as the arduino supply ground ?
@robojax
5 жыл бұрын
yes. Shared ground.
@thequiet8353
5 жыл бұрын
Can you control using a potentiometer?
@robojax
5 жыл бұрын
yes you can. I just add it to my "to do" list.
@ruanvanheerden3906
2 жыл бұрын
I need some help. My Mosfet drivers seem to work perfectly just like in the video, but then something happened and now my module outputs the same voltage as the input voltage without the PWM pin being powered, almost like it is short circuiting. Has anyone had any problems like this ? Please help if possible
@papa8293
Жыл бұрын
I had the same issue. I found that a load needed to be put on the out put before the unit would put out the adjusted volts
@tejaranganath9517
3 жыл бұрын
how to use it for rotating motor reverse
@robojax
3 жыл бұрын
if you want only CW or CCW direction just change the wire connection. but if you want to revers the direction of rotation, this module is not for that.
@khennuhfussanjaya2325
3 жыл бұрын
can this be used to a charger for 18650 batteries?
@robojax
3 жыл бұрын
No. not at all. Watch this to learn about Lithium battery and protection kzitem.info/news/bejne/kaOF16R5n3OVrGk or for 1A watch this kzitem.info/news/bejne/lJqtp2x3cYijpXo
@khennuhfussanjaya2325
3 жыл бұрын
@@robojax But can this module adjust the PWM voltage for charging battery?
@khennuhfussanjaya2325
3 жыл бұрын
@@robojax can this module adjust the PWM voltage using Arduino?
@nissimzur1
4 жыл бұрын
what is the name of windows application you are using?
@robojax
4 жыл бұрын
which window? The first on is Arduino IDE a free program you can get from Arduino.cc and the 2nd, you can see the title Rigo Ultra Load. it comes with my Electronic Load (hardware).
@Delorean29
3 жыл бұрын
I need schematic for 400W Where can I find?
@robojax
3 жыл бұрын
are you talking about the schematic for this module itself? this is very simple, you just look at each components and draw it on this website easyeda.com/ it is free and you can do it online whiteout installing it.
@Delorean29
3 жыл бұрын
I use Easyeda very much 5 cards about 27 - 29 dollars with shipping. Very cheap :)
@geejavile
4 жыл бұрын
can this be used to an airsoft gun?
@robojax
4 жыл бұрын
It can be used with DC load and the current is important. You can't go beyond the load limit. I have explained and tested the load capacity of this in video. Please watch it till the end.
@geejavile
4 жыл бұрын
@@robojax i sent a message on fb. Do you reply there?
Пікірлер: 219