Great way to start a video. You almost blew my ears out with my headphones on!!
@1234tracer1234
Жыл бұрын
WOW, this is so educational. Excellent work
@festoolaustralia
Жыл бұрын
Glad you enjoyed it
@illecebris8709
3 жыл бұрын
Just received my Festool MFT/3 and it is a wonderful tabel and fantastic design! The tabel is a little bit to high for little woodworkers like me.. 😊
@ianwarham428
2 жыл бұрын
My festool saw just stopped working any ideas what would be up with it
@Jamescharles2k11
2 жыл бұрын
I have the older brushed model from 2009! When the brushes go, the safety activates for it to stop being used. Maybe this is the same issue as yours?
@StylishDeathbat67
Жыл бұрын
Great saw especially kzitem.infoUgkxxnKxcY0vm4xjW8xkPbjaHuKt10gr-wG_ considering how drastically cheaper it is than every other track saw on the market. Only things I would mention is replace the blade immediately, the 24 tooth blade supplied leaves a lot to be desired.
@pekkahollola7646
Жыл бұрын
Can I use other than S 75/4 FSG saw blade for Trion PS 300 ? Manual says "Use only S 75/4 FSG blade with guide rails." Anyone know why other blades are not usable ? Makita has similar rule "Always use Makita blades No. B-8, B-13, B-16,B-17 or 58 when using the guide rail and the guide rail adapter".
@festoolaustralia
Жыл бұрын
The blade can be used for any application that it suits. the reason for recommendation of the blade being with guide rails ets. is that it is very stable and is most suited for these applications as the blade is less likely to divert.
@pekkahollola7646
Жыл бұрын
@@festoolaustralia Ok I have 20mm birch plywood to cut with rail guide. Planning to have a fine cut. Is the cut achieved very coarse with S75/4 FSG ? It feels like a coarse blade.
@festoolaustralia
Жыл бұрын
@@pekkahollola7646 The FSG blades are designed for use with guide rail adaptors in combination with jigsaws as the blade has good stability and is less likely to deflect. The cut however is not a fine cut but can be improved significantly with the addition of a blade splinterguard (490120) for the jigsaw.
@pekkahollola7646
Жыл бұрын
@@festoolaustralia Yes. Mission successful during weekend. 20mm birch plywood used: PS 300 Trion, guide rails 2x1400mm, splinter guards 2x. After 6pcs of 2500mm birch plywoods cut half total 15 meters (2,5m*6x, depth 20mm) the new blade was somewhat dull S 75/4 FSG. I should have used 2x blades. How much meters before you can expect a blade change ? Is it somewhere around 7 meters of cut then change a new blade ?
@delvario1758
3 жыл бұрын
Professional tools
@williamchase3500
3 жыл бұрын
Is the bottom of the rail grippy enough to not need clamps?
@gordonwilkinson2911
3 жыл бұрын
Most times I find if I apply even pressure then I don’t need clamps but you will need to make sure the material surface is as dust free as possible first. This is the same for all the lengths of rail but obviously the neoprene strips have a much better hold on the longer rails.
@patrick5502
3 жыл бұрын
🔝👍
@lorenarmstrong7088
3 жыл бұрын
Way too.much saw dust blows out at the end of every cut. How is that acceptable in any shop or home remodel from a fine tool maker?
@metishaqiri3284
3 жыл бұрын
Gruss Mike Was kostet es
@lucaplett6553
2 жыл бұрын
My guide are 4 mm off and there is no way to calibrate 🥲
Пікірлер: 20