It's awesome that you tackled this at home. It's a very cool rebuild series!
@CleffersGarage
8 ай бұрын
I am surprised it was as easy as it was.
@simonsautorepair8082
2 күн бұрын
What's the part number of your engine stand?
@jeremygrech-xz3lb
4 ай бұрын
Good job man!
@CleffersGarage
4 ай бұрын
Thanks! it's been a fun project so far.
@nickolivares7831
7 ай бұрын
Did you send the block and crank out to get cleaned and honed, or you did it yourself? Looks good! Also why did you opt to go with a different block other than rebuild the spun bearing motor?
@CleffersGarage
7 ай бұрын
I was going to reuse all the parts from the original but I couldn’t find anyone near me that could line bore a block it had some deep groove in the bearing surfaces. I think I only payed $1000 for the other engine. And that was pretty much a good bottom end except the 4 pistons.
@user-dj6wz5me7p
7 ай бұрын
Nice visual! Wish he were near Denver as I have a real nice (152k miles) 2016 F350, 6.7 Diesel, that I have been waiting almost 6 months for a new Ford engine. No one willing to troubleshoot this one with a tap or knock. Where is Cleffers Garage?
@user-dj6wz5me7p
6 ай бұрын
With excellent service like this, how come there is no response?
@CleffersGarage
6 ай бұрын
I’m in eastern New Mexico.
@darrellbanks4998
9 ай бұрын
I was just wondering if you put a check valve in the pick up tube on the oil pump. I was videos when they said they had a lot of problem with the oil running back into the Pan after the engine was shut off.
@CleffersGarage
4 ай бұрын
i don't think i did.
@qrptoqro7834
4 ай бұрын
I can't recall if it was this video, or the previous, but you addressed the tracking of the injectors (as in the injectors are addressed specifically to the computer to fire in the right sequence). Aside from keeping the injectors in order (for the above reason) - is there anything electrical/sequencing that needs to be kept in check/tuned? IE - is Forescan required to do the mechanical tear down and rebuild in order to get it to run right when put back together? If it is - to what degree can a successful rebuild be done and wrapped up without it - as in can the truck be driven until proper tuning/adjustment post-rebuild can be done? Enough to get to a shop to do the tuning? Or beyond? Mine is a 2011 with a bit under 200k miles, barely runs.
@CleffersGarage
4 ай бұрын
i don't think i had to do anything with forscan. i just made sure all the injectors went in the same spot they were. everything just kinda worked. you should be able to do the whole job without a tuner as long as you aren't replacing the injectors.
@qrptoqro7834
4 ай бұрын
@@CleffersGarage Do you have any current updates on how the engine is running/holding up? On your first start video it was pretty noisy. Were those issues corrected? And what did you find with the sources of the noise/issues that caused the noise? Thanks!
@WaterandWoodsmen
Жыл бұрын
Valves most likely caused the failure the glow plugs are secondary after the valves fall apart bet it was passenger side I pulled the passenger head off once I got contribution balance codes in 3-4 cylinders and found cracked valves that hadn’t fell apart
@WaterandWoodsmen
Жыл бұрын
I would tig weld the crank gear before you install front cover
@CleffersGarage
4 ай бұрын
I should have now i'm going to always be worried about it.
@Jhonkanator
Жыл бұрын
I wish I found this channel earlier. looks good.
@CleffersGarage
Жыл бұрын
Thank you!
@michaelhowe901
4 ай бұрын
What assembly manual did you follow? Anyway you would mind sharing a link so I can follow along? By chance does it show Ring gap measurements?
@Davidps15
Жыл бұрын
Looking good
@SantosRamos-be7ju
4 ай бұрын
What is the torque specs for the rocker arms?
@CleffersGarage
4 ай бұрын
I think I used this. www.engineprofessional.com/TB/TB072517-2.pdf
@chrisbee534
25 күн бұрын
How much would you charge to do this for a customer ?
@JonathanBashor
2 ай бұрын
Nice work, doing my 6.7 now. Do you have a link for the plate to lift it from the turbo pedestal?
@CleffersGarage
2 ай бұрын
I ended up making one because I wasn’t will to pay the price that was being asked for them. If I was going to buy one it would be something similar to this www.freedomracing.com/engine-removal-bracket-303-1518.html
@jasonsopko2651
Ай бұрын
Are you putting the new style fuel pump or the cp4?
@CleffersGarage
Ай бұрын
Right now I just have the original cp4 in it. I want to get a disaster prevent kit for it and maybe a cp4 that has pinned lobes in it.
@jasonsopko2651
Ай бұрын
@@CleffersGarage just a suggestion, put the money you'd spend on the disaster prevention kit and get the DCR pump instead.
@CleffersGarage
Ай бұрын
@@jasonsopko2651 oh yeah I forgot got about those I’ll probably do that.
@ralphcarruth2643
9 ай бұрын
When you put it in the bronco. Will you be using a stand alone harness? Or do they even make them yet ?
@CleffersGarage
9 ай бұрын
At the moment the plan is to use everything from the 6.7 truck and maybe remove/code out things with FORScan.
@Story53s
9 ай бұрын
Did you use the block out of your donor truck? If so did you find someone locally to clean it?
@CleffersGarage
9 ай бұрын
I ended up finding a used engine a few hours away from me that had dropped glow plugs in one side. The block looked good just replaced those 4 pistons and the head
@germangarcia4143
5 ай бұрын
What was the total cost on this rebuild ?
@CleffersGarage
4 ай бұрын
I think between the new used block and all the gaskets and such it was about $2500
@bradyspears8318
9 ай бұрын
How did you get that cash aluminum so clean?
@CleffersGarage
8 ай бұрын
I used a product called wire wheel cleaner that I got from o'reilly auto parts. It’s behind the counter you have to ask for it
@HSKFabrications
10 ай бұрын
Didn't weld the crank gear?
@CleffersGarage
10 ай бұрын
No I did not end up welding it
@HSKFabrications
10 ай бұрын
@@CleffersGarage That's one thing that should be done while you're in that deep already.
@oneofakindmr2
Жыл бұрын
I have a question. Was that mayonnaise you used as crank lube? I watched your video and used it on my engine build and now I spun 3 bearings upon start up…
Пікірлер: 43