For more bike repair videos hit the subscribe button 🛑 and click the notification bell ► bit.ly/SubRJTheBikeGuy
@Ethan-nw5uk
5 жыл бұрын
Hey i have a 15/16th size stem will this work?
@bnick25352535
4 жыл бұрын
Have a Cannondale sl4 has 1.5 head tube,not to many options in stems out there can i use a 11/8 somehow with a shim or to dangerous ived heard.
@RJTheBikeGuy
4 жыл бұрын
@@bnick25352535 You mean install a 1 1/8 fork? I wouldn't do it. Try to find an oversized fork. Check ebay.
@hubertdevocion2449
2 жыл бұрын
Hi sir, i really need your help. I have a 26er standard steel MTB and i wanted to replace the fork but i'm not sure if the fork that i'll replace will fit to the head tube. I bought a 26er fork and the upper tube measures 28.6, i just wan't to ask you sir if the fork that i bought will fit to my standard MTB. I wanted to do some upgrades of my bike and i hope you can help me sir ☺ thank you so much.
@tobins6800
5 жыл бұрын
Hint and tip, a socket or 2 in the headtube that fits without binding inside can greatly assist in keeping the all-thread centered.
@AindriuMacGiollaEoin
4 жыл бұрын
I'm going to change my old MTB from 1 inch threaded to 1 inch threadless, this video helped a lot
@sunfirefilms000
4 жыл бұрын
i bought step down headset cups for three sizes, 1", 1 1/8, and 1 1/4. They're just the cups, and I used your ideas for the homemade press! The cups alone are around $30, and it makes it a lot easier to press in the headset. The park press is like over $100, so it's a great compromise between the two! Thanks RJ for another awesome video.
@Simo-qg6jb
8 жыл бұрын
Probably This is Best Bike KZitem Chanel !!
@kacooksabasakusina2905
6 жыл бұрын
gmbn is the best
@thatthingyoudo6398
5 жыл бұрын
Perhaps in english. in spanish we have mundomammoth and is great also
@mouthpiece9980
4 жыл бұрын
Hi my name is Jerry and I'm a lifelong bike enthusiast and I like your Channel but I need to ask just to see if I'm right or wrong when you put that dust ring around the stem before the spacers I'm thinking it should have been put on after the spacers please let me know if I'm wrong all right thank you!
@SFCRambo60
6 жыл бұрын
You should put your cups in the freezer for a couple hours, they will almost fall in. Even just use a hair dryer to heat up the tube before installing will help.
@KarlosEPM
3 жыл бұрын
@SFCRambo60 is this really true? I'm renovating an old bike and this would help me tons.
@kieranh2005
2 жыл бұрын
Yup. Best if you do both. Shrink the cups and expand the steering head.
@ericwarburton
Жыл бұрын
🤦♂️ Use a cup press and grease.
@NikkiNexo777
2 жыл бұрын
This video popped up in my KZitem feed today and came at the perfect time. I'm converting a 1" threaded to a 1 and 1/8 Threadless on a Schwinn klunker project with BMX bars. Great video! This conversion is much easier than I anticipated. Thanks again.
@nuclearguitarfare4653
Жыл бұрын
Can't be anymore of a clunker than my royce union someone gave me for helping him move lol. But it has a euro bottom bracket so I rebuilt it. Replaced everything but the forks sofar. Turned out to be a pretty nice ride!
@lifelong5425
7 жыл бұрын
Amazed at the flow of process, and the sudden desire I have to tackle these projects, as I am about to get a vintage bike to enjoy, and perhaps do some upgrades on....The videos are wonderfully easy to follow.
@unclefreddieDied
5 жыл бұрын
awesome 👍 I grabbed a bike that was out for the trash... thanks to these videos I'm gonna be doing some upgrades... been a while since I've been out on a mountain bike! thanks RJ for the inspiration!
@smiff4748
9 жыл бұрын
Greetings from the UK. Thank you so much for this my friend. I have watched quite a few video's concerning changing to a threadless headset but they were in no way as good as your video. You explained everything so that even an old fart like me could understand how to do this task. Keep up the excellent work. Once again thank you.
@xenon9887
9 жыл бұрын
If you trapped the washers touching the cup between two tightened bolts, it would ensure that the pressing surface is always straight. Then you only have to worry about the set of washers on the end you are tightening.
@ver251209
2 жыл бұрын
nuts
@JamesDavis-kp4ll
Жыл бұрын
That's a good point, I just "upgraded" mine, thanks! 👍 Although you did mean nuts, but still..., 🤝
@stitchilalu
5 жыл бұрын
Absolutely love your videos. I hadnt seen this one before but I wanted to check your methods considering I am going to be putting some threadless forks on a few frames. I love that you dont use commercial tools. I use most of these methods myself. I don't have cups installed on the frames but loving that split metal tube for removing the cups, its just simple and brilliant. This kind of thing really allows bike building and maintenance to be accessible. Thank you, I really appreciate it
@pahaahv
5 жыл бұрын
Threaded stems have one very important advantage for me as opposed to threadless stems and that is adjustable height. I have a Scott MTB I picked up for 20 bucks and it would be perfect if I could raise the handlebars maybe 5 cm higher, but it's threadless stem is already as low as it can be and the fork tube is cut to the exact size in factory. Right now having done maintenance on older and newer bikes I'd say the stems and saddle attachments look better nowadays but were easier to work with way back when.
@RJTheBikeGuy
5 жыл бұрын
Threadless stem come in different lengths and angles to help adjust height. As well as the spacers.
@matrixracing8268
4 жыл бұрын
I Found a Old Roadmaster Steel Frame With Everything On It and I Put my Suntour XCT Fork On It and Then I Went Mountain Biking! ThankYou For The Tutorial!
@himawariuzumaki1320
4 жыл бұрын
Suntour xct with the spring? I think i have that one too. I didn't know the headset is the only problem inorder for me to use the other fork.
@CGGarage
4 жыл бұрын
I put the same set of forks on today on my 90s huffy mtb! How do you like the shocks?
@matrixracing8268
4 жыл бұрын
@@CGGarage Fork Or Shock?
@supamadevu4512
5 жыл бұрын
Love the elbow grease and Flintstone tech used, exactly what I need for my (not sure yet) next project. Love when I can do the job without spending in expensives one time use tools. Thanks again.
@mockingbird_proxi
9 ай бұрын
I thought I broke my headset since the tube with thread broke. The first picture of the threaded fork cleared my vision😅 That good damn threaded tube was part of the fork. Now the Threadless conversation is justified🤤
@victorlozada1
9 жыл бұрын
Thanks for the video simply and perfectly explained, in my personal opinion I prefer a threadless fork because transform your bike completely and give a fresh look thanks again for the video and God bless you
@DMGamer_PC
Жыл бұрын
Genuinely thought that because I was going from 1 1/8 threaded to 1 1/8 threadless I could use the same pieces... Didn't realize until I had everything ready that I had no way to tighten down the caps for the bearings x3 Thank you for the informational video; also realizing I need to hit up my local hardware store so I can jury rig some press/impact tools with some threaded rods and washers. Love to see homemade tools perform as well as custom ones!
@williamthornton8151
7 жыл бұрын
I just wanna say thank you so much for making your videos. This one specifically and the headset cup remove tool and press tool helped me tremendously and my build is now complete. Your the best man
@SuperOlds88
2 жыл бұрын
Nice video. Only thing I would add is grease on threads of all screws and internal metal parts that could be tough to disassemble especially since this area can be highly corroded because of sweat. Thanks for a another good video.
@RJTheBikeGuy
9 жыл бұрын
SuperSayanFitness, I wouldn't call it a "low quality" suspension fork. It is a good fork, just not the latest and greatest. But most of the newest forks are set up for disc brakes and don't even have the mounts for cantilever/v-brakes.
@creaturedanaaaaa
7 жыл бұрын
What if I sawed off the threadless steerer tube, welded on a 1 inch threaded one and then just used an amazon threaded to threadless fork converter?
@RJTheBikeGuy
7 жыл бұрын
You are on your own with that! Keep in mind, when a fork fails, it generally fails catastrophically at the worst time.
@paulavram2759
7 жыл бұрын
how i replace a suspension fork but my handle bar is a old one and i dont have a better one?
@wecf1411
4 жыл бұрын
Pateu Vegetal try to buy one off a friend or find a good deal on craigslist, eBay or any other selling platform. Maybe a bike shop might have one to sell for cheap.
@casperadventures9569
3 жыл бұрын
@@RJTheBikeGuy it is 25.4 fork?
@TheAugiedoggie1
8 жыл бұрын
AWSOME video! I have a Trek 970 I am converting to a Trekking bike and want to update to threadless head set. You just showed me how to do this. On a side note I started cycling in the mid 80's and learned to do my own maintenance on my 7 bikes (all Treks). Your grip trick using alcohol was cool. I used to use women's hair spray which also acted as a glue when dried holding the grip in place. I have subscribed to your video's which will help me build this bike. Thanks!!
@chosenideahandle
Жыл бұрын
Can you use men's hairspray? Lol.
@TekDristan
5 жыл бұрын
Good information, as always. I tend to shy away from bikes with threaded headsets. Now I know how to change it if need be.
@schrodingerthecat
2 жыл бұрын
6 years after you posted this video helped me out upgrading my old GT mountain bike. Thank you!
@fceuropa
9 ай бұрын
Answered 90% of my questions in the first 2 minutes. RJ you have amazing presentation skills. Nothing missed, nothing extra. Love it.
@upstatecre8
4 жыл бұрын
I just did this job this weekend and made those homemade tools too!!!!
@BlackJacketWasp
2 жыл бұрын
Thanks for yet another definitive tutorial. As always, I am grateful that I don't have to do a trial-and-error.
@SonnetGomes
2 жыл бұрын
Thank you so much. This is a very helpful video. If not for this video, I would have probably had the headset reversed. Glad I found this video. Can't thank you enough for how immensely for all you do and how helpful all your videos are. Thank you!
@himeno_istri_ku
3 ай бұрын
Its 2024 and im about to work on my bike, thanks for making this video if not because of you, my bike gonna be screwed
@Grizzly907LA
4 жыл бұрын
Seems, pretty straight forward. You and others got me inspired. Bought three frames today, and hopefully I can build at least one bike.
@IanLoughead
9 жыл бұрын
Great video. For my bike I didn't need a new fork as much as I wanted a better stem option (the Quill stem didn't work for me). I found a great adapter which has served me very well. They come in 1 inch and 1 1/8 inch. A search for quill adapter will find it quickly, in case anyone wants a slightly cheaper option or doesn't need the whole fork changed out.
@RJTheBikeGuy
9 жыл бұрын
Ian Loughead I have a couple videos on those. kzitem.info/news/bejne/14ai1mGVnaFjoII
@IanLoughead
9 жыл бұрын
RJ The Bike Guy Yes, it seems you do! Thanks again!
@joebananas4741
7 жыл бұрын
Very good video. Clear and concise instructions. Love the homemade tools. That little grease gun is neat too. I'm actually thinking of junking my sprung fork for a rigid as it is so heavy. At least I now know the difference between threaded and threadless.
@RJTheBikeGuy
7 жыл бұрын
Going from a suspension fork to a rigid fork will likely lower the front end of your bike and change the geometry.
@DBDUFIEBTHDHDV
4 жыл бұрын
MUST AMAZING AND NECESARY VIDEO EEEEEVEEEEER! I mean it. I have a threaded fork and I didn't think a conversion could be possible. I can make my bike better. Thank you so much!
@cristianomoreira8775
Жыл бұрын
Man congrats for this video, serious. For monts i seach for some solution for the problem of my old bike and on the Brazil don't find nothing too easy like this on your video! I'm glad for this channel exist and in this moment i will order my solution on the amazon lol! Hug from Brazil!
@THEfromkentucky
7 жыл бұрын
That looks exactly like my 1997 Trek 820, and I've been wanting to do a threadless conversion on it for some time. Thanks for laying it all out.
@whynugs
3 ай бұрын
Bike tools company will hate you😂 Thanks a lot RJ!!!
@upstatecre8
4 жыл бұрын
Great video RJ! I recently tried removing handle grips with an air compressor and was super impressed at how easy they can off! Keep the great instructive videos coming and thank you!!!!!
@RJTheBikeGuy
4 жыл бұрын
I have don that too. But since I don't leave my compressor powered up, it's a bit inconvenient.
@RJTheBikeGuy
4 жыл бұрын
kzitem.info/news/bejne/0aeg24VvbXOjjHY
@chosenideahandle
Жыл бұрын
I've always used wd40. I like the alcohol idea (cleaner, and takes less time to disappear).
@limegreen4956
5 жыл бұрын
Great video! Very helpful and easy to follow.
@RobboHouTex
7 жыл бұрын
Great video. I've been thinking about this project with one of my old hybrid bikes and this video answered all of my questions. Thanks.
@scottscotts808
3 жыл бұрын
I like what you are doing by helping others without the knowhow and I'm sure you have save a lot of people a lot of money, I do find on some of your tutorials you are making it more complicated then need be, I'd never use or recommend this method of putting bearing cups in, all you will do is over tighten and leave a nice cracking in the frame. Believe me iv seen this a few times
@RJTheBikeGuy
3 жыл бұрын
The headset cups are pressed in. That is how it's done. I used a homemade tool, as the professional headset presses are expensive. www.amazon.com/exec/obidos/ASIN/B000R2JJLW/ref=nosim/youtube25-20
@neomanis
8 жыл бұрын
Man, those tool innovations are on the fucking point! Smart, cheap, reliable! Kudos!
@Spanky8402
5 жыл бұрын
I made my own tool just like yours but I used a 2x4 on the bottom end and I scored the area of the wood where the cup would be and that helped keep the tool in place. I scored the wood using a file. I basically made a circle in the wood. I appreciate you making this video. :)
@recyclespinning9839
4 жыл бұрын
Thank you , will be attempting this on s Trek 930 I trying to convert to drop bars . It also has a broken suspension fork end on it . I am going to ridgid fork. More to this than how easy you make it look, tools, right parts , where to buy , right grease , right torque setting etc ...
@kght222
6 жыл бұрын
on your homemade headset press, use a second nut on the bottom that way you only need one tool to tighten it down, might make it less of a headache to use.
@Gulgonful
Жыл бұрын
Thanks RJ I recently pressed a headset using a screw down wood clamp and some wood blocks - if you take your time it’s no big deal. Park Tool who?
@norberth3778
7 жыл бұрын
For the top part make a cylinder with a centered hole for the bolt, this will go in the frame to center your tool, wood or plastic or other material can be used.
@eddon7644
3 жыл бұрын
One of my fave bike channel!! Hugs from Chile!
@robbocyprus
8 жыл бұрын
Very Good RJ your videos are very helpful, very concise and you do everything in a methodical and timely way! I noticed that the Pepsi cans went down rapidly during the making of the video ;-}
@fadqih8970
4 жыл бұрын
Those DIY tools was so dope!!!
@8day1989
8 жыл бұрын
+RJ The Bike Guy Have you considered putting wooden cylinder with a hole in the middle of this device? It should provide fast and decent centering w/o damaging inner sides of tubes. Also, you can make that cylinder a bit smaller than needed and adjust its diameter with some tape/paper/whatever. I bet some carpenter can make it for a relatively low price. Oh... after a bit of thinking I realised that you won't be able to use it for the other cap... I guess in that case you can use another cylinder of a smaller size. But now it seems like it creates more trouble than it is supposed to solve...
@surfcitygenecarrothersabec7634
3 жыл бұрын
Nice Socks! Thanks for posting I had no idea about a threadless fork!! Very interesting i have a Trek 830 and 850 mountain bike from 1982.
@gpurkeljc
5 жыл бұрын
I have a Look carbon fork with a 1 inch threadless steerer that I'm never likely to use again. I didn't even realise that they are difficult to find.
@christooss
4 жыл бұрын
I sometimes watch RJ The Bike Guy's videos when I'm bored.
@Nix-Travels
4 жыл бұрын
Love the homemade tools
@sethstanbury6126
6 жыл бұрын
Thank you for a really helpful video, I have been wanting to do this to my 88’ specialized for a while now😊
@xcrypticsamurai7908
4 жыл бұрын
Wow I have been looking for how to do this and you just made it so easy for me. Thank you so much for making this! helped me a ton
@kottelkannim4919
3 жыл бұрын
DIY-ers should note that the handlebar is not oversized (1 1/8") but rather a 1" one. This reflects on the stem's dimensions, namely it has 1 1/8" steerer tube clamp and 1" handlebar clamp, like in the Bontrager one that RJ used.
@RJTheBikeGuy
3 жыл бұрын
The handlebar diameter only matters for what stem you use. And really doesn't matter for changing the headset.
@hoosebrickhighlander3678
6 жыл бұрын
A solid spacer in the middle would have it centred, obviously it would fit snug in the head tube with a hole drilled for ur threaded bar.
@TyBraek
6 жыл бұрын
I'd recommend spend the extra couple dollars and get the FSA orbit. It comes with sealed bearings. Much easier to deal with for about $20
@TboneTenEighties
5 жыл бұрын
Keeping my threaded on my road bike. My steele fork is way to comfy of a ride to change out. I really couldn't care if it's heavy. Feels damn great on the road. Stiff on smooth flats/climbs and soft on bumpy terrain. Sometimes i have to look down at my front wheel because it feels like my tire is low but it never is lol..the damn thing feels like a shock absorber. I just use an adaptor so i can use a threadless stem on my threaded fork. Perfect.
@FirstnameLastname-pe5ib
5 жыл бұрын
If it feels like a flat it has loosened.
@TboneTenEighties
5 жыл бұрын
@@FirstnameLastname-pe5ib I know what you're saying but nothing is loose. I have been working on my bikes since a teen. The only thing i take it into a shop for is wheels truing. I have done it before but sooo much easier to get it done from my local.
@oxXHITMANXxo508
9 жыл бұрын
RJ The Bike Guy Love the vids man keep them coming :)
@a.m.6713
8 жыл бұрын
AWESOME...Thanks for your time and the video!
@jpkancertech3874
9 жыл бұрын
i didn' t need a crown race installer ... i just took it on the fire til it was enlarged enough to get it straght on the steerer tube without pressure ... i just got it on there and done
@tomasperezalvarado4133
2 жыл бұрын
No entiendo el inglés pero si entendí como isiste el montaje y eres una persona muy inteligente usas tus propias erramientas
@Scubasig
8 жыл бұрын
Nice video! very informative. You must have been thirsty because there were 3 cases of Diet Pepsi in the beginning and at the end only one was left! lol Looking to do this conversion for a Cannondale Headstock (1.5") to a threadless rigid fork (1-1/8"). Hoping the process is as strait forward as this. Thanks !
@dinhphuochoa
9 жыл бұрын
I've just bought a Trek 830 which i think 1995 model (internet search). It appears to have 1 inch headtube because a quill stem installed on its fork. I saw your video and your Trek 820 has a 1 1/8 inch headtube. I hope that my Trek 830 1995 has the same diameter. Thank you!
You could measure the diameter of the quill stem. the stem for a 1" fork will be about 7/8". The stem for a 1 1/8" will be about 1" in diameter.
@user-ih7yp8wu7z
7 жыл бұрын
Great video! Simple and clear! ))) Especially liked the tubular puller)))
@LesterWalters
5 жыл бұрын
Looking forward to doing the same thing on one of my bikes.
@marcosruiz3175
3 жыл бұрын
Great video , it is very helpful ,greetings from Argentina
@jesse-xj2fs
4 жыл бұрын
Thank you so much man, i now finaly know how to upgrade my crappy downhill bike. Thank you so much
@patricus1749
8 жыл бұрын
Hi RJ any vids for 1 1/8" to a 1"?
@mazda3mike
5 жыл бұрын
Same thing in reverse 😂
@maxmiser286
7 жыл бұрын
You do love your treks don't you RJ. Another great video. 👍
@mckav2358
3 жыл бұрын
Hi RJ This is exactly what i needed to learn Thanks
@-san_mac-
4 жыл бұрын
Your home made tools are awesome
@ns9743
5 жыл бұрын
This is what i needed
@robertkelly1434
2 жыл бұрын
Glad I found this video, I'm planning an upgrade on my touring bike from rigid to suspension forks. I have no idea what the current fork shaft measures. I did replace the steering head and handlebars a few years ago, installing a 1" shaft. There's some play around that shaft, so I'm thinking I may be lucky and have a 11/8" tube. Where should I measure it to be sure (preferably w/o removing that front fork)?
@aaz_m_t_b
2 жыл бұрын
Really helpful video
@Racing_club777
5 жыл бұрын
Another great video. I'm going to addicted jajaja.saludos amigo.
@olivertorres2193
6 жыл бұрын
I love your home-made tools, really usefull
@TommyShlong
7 жыл бұрын
RJ The Bike Guy - Yet another great video! I dont know if you'll see this as the video is from 2015 but you mention using "marine grease". What brands or types should I specifically look for? Also, why do you like using marine grease over bike specific grease?
@superchile9640
3 жыл бұрын
Now I know how to do this to my older Trek
@ericmiranda9841
8 жыл бұрын
I am having nightmares about that grease gun. ja ja ja great video dude.
@HaydenMarek
5 жыл бұрын
great video, thanks, is it possible to link the headset you used please?
Try putting it in the freezer and warming the tube with a heat gun before pressing in, will go in a little bit easier
@alonzomartii
7 жыл бұрын
Ooh man, that tap that down sounded dirty. LoL
@myscreen2urs
4 жыл бұрын
I'm in the process of doing a threadless conversation and I just learned the hard way that sealed beating headsets won't fit if you were previously using cage bearings. I agonized about the specs too when choosing this headset
@RJTheBikeGuy
4 жыл бұрын
You use a sealed bearing headset if the specs match the head tube and steerer measurements. Were you trying to reuse the old cups?
@myscreen2urs
4 жыл бұрын
@@RJTheBikeGuy No. But after doing more research, it would seem that I bought a semi integrated headset when I should have gotten an external type. The one I bought had it so that the bearing presses into the headtube instead of above and below like the ones your demonstrating in your video.
@RJTheBikeGuy
4 жыл бұрын
@@myscreen2urs Yep, as I said, the headset need to match the specs of the head tube and steerer.
@OldschoolDT
6 жыл бұрын
I love your homemade tools!
@hoangnguyendinh291
Жыл бұрын
looks good. but i love quill stem
@youtbnyaindra
9 жыл бұрын
Hi RJ, nice videos you have made for bike thinker like me. But since I am new in bike modification or and maintenance, I wonder if you could explain to us why do you change these forks thread and perhaps also for your upcoming videos (why do I need to change it, if its not due to worn out)? Keep the awesome videos coming!
@RJTheBikeGuy
9 жыл бұрын
Indrawibawa I Nyoman You don't need to do this. I did it because I could and I thought it would be cool and fun. Threadless forks/headsets are a newer technology. And lots of people have asked how to do it.
@discount11
2 жыл бұрын
great video! Thanks for making this.
@chrismad1344
8 жыл бұрын
You da man,I'm learning a lot with you videos thank you!
@downhill_rider732
Жыл бұрын
U saved me hundreds of money
@carlosfigueroa790
4 жыл бұрын
Cheers from Central America. Guatemala city.
@carlosamador8085
9 жыл бұрын
RJ Awesome videos like always!!
@PedroElena1000
4 жыл бұрын
Very good video¡ I wonder if you had the opportunity to replace the hub in a Spinergy rev X wheel? Would be interesting to see how you applied solution to this problem
@RJTheBikeGuy
4 жыл бұрын
I have not worked on one of those.
@kevinhullinger8743
6 жыл бұрын
Thanks for the video great information and pointers.
@b0tak707
9 жыл бұрын
This is so cooooooool!! So detailed. Beautiful/ :)
@clockwork9827
7 жыл бұрын
good how-to with proviso for measurements/types of headtube at beginning. like the homemade tools featured. will chk vids
@808GT
7 жыл бұрын
Great tutorial! Helped me do my conversion.
@normanklein3155
3 жыл бұрын
Why would you want to convert from a threaded to a threadless fork? What is the advantage of a threadless fork design?
@fabiomaragna
3 жыл бұрын
Awesome video! I am about to swap my quill stem for a threadless but maintaining the original fork (i'll use an adapter). Will i need to any other component for the job? A paet some spacers i guess...
Пікірлер: 606