neat trick using washers to figure spacer width. super simple
@Corn-ped
2 жыл бұрын
Yeah i use to try to measure... But this is way easier
@ace_pororo1455
Жыл бұрын
the wheel spinning so damn smooth
@Corn-ped
Жыл бұрын
yeah! soooo smoooth!
@KelikakuCoutin
2 жыл бұрын
Came here from the 'Moped Army'. Subscribed. Excellent production values - very well done video, in my opinion. Thanks for the content. Keep up the good work. בס'ד
@logandumais7442
Жыл бұрын
Man, if it wasn’t for this video I would have never known a spacer was needed between that bearing and the brake plate! Could never figure out why the wheel kept pretty much locking up when I went to tighten the axle nuts real snug. Thank you so much.
@Corn-ped
Жыл бұрын
Yeah. That is super important!
@logandumais7442
Жыл бұрын
Hey do you sell parts by chance? I’ve been looking for a front brake plate for my pinto but cant find any on treats or anywhere online. Running only rear brakes right now.
@Corn-ped
Жыл бұрын
What kind of rims are they? Shoot me an email with a photo of the wheels. Cornped@gmail.com
@logandumais7442
Жыл бұрын
Believe I’ve got the same as you. Grimeca 5 stars I’ll email ya!
@Corn-ped
Жыл бұрын
www.jmpbparts.com/brake-anchor-plate-front-puch-maxi.html or www.puchshop.de/en-gb/brake-torque-plate-front-wheel-puch-maxi.html?_gl=1*1xi2f8o*_up*MQ..&gclid=Cj0KCQjwsrWZBhC4ARIsAGGUJur9wNPFXJXZIVnnzP7Z5HCaKrXFIB2fCdtvWGDOWHr3-rs7FAbswFoaAlXaEALw_wcB But I'm sure I have a spare.
@dahomieplaysthegame7113
Жыл бұрын
Good looking out bro atleast u showing people
@mikegamba580
Жыл бұрын
Always using your videos to help me fix my puch Ive already watched this video for fun now I'm watching it again because you know exactly what you're doing and I need to know exhaust what I'm doing because I ride this thing every day
@Corn-ped
Жыл бұрын
awsome! glad I can help!
@rootstowingsyogahealingnew2101
3 жыл бұрын
I’d love to see you take a maxi roller and redo the whole bike from tank to toot with a rebuild, porting. Your bikes are so clean that it’s like working on ferraris compared to what most of us are working on. Like I have a maxi I just tore down to paint with everything in zip lock bags and it’d be really useful to know the things I should do compared to just slapping everything back together. What do I do to the magneto, cables, wiring block, hubs, clutch, ports. All that
@Corn-ped
3 жыл бұрын
I would love to do that. If I do a full rebuild I will film it. I have a lot of random projects at the moment.
@johnkillick6061
2 жыл бұрын
With a little bit of knowledge, and few good tools ⚒️ its amazing what can be accomplished .👍🏴
@hagbardceline5358
2 жыл бұрын
I want to get another moped so bad. It's been around a decade since I last had a few.
@Corn-ped
2 жыл бұрын
Now is the perfect time. They go a lot cheaper in the winter
@hagbardceline5358
2 жыл бұрын
@@Corn-ped Yeah but I'm broke after all the shopping, lol. I keep an eye on what's for sale around here, though. The only proper moped I've seen in the last few months was a Vespa Ciao that was complete with extra parts and I still kick myself for not just buying it.
@Corn-ped
2 жыл бұрын
Where are you located?
@Corn-ped
2 жыл бұрын
Check out Facebook market place and Craigslist. Thats where I find most of mine.
@janhoogesteger
2 жыл бұрын
Dude. Thanks a lot. I can use this to fix my rear wheel
@adamharlow8124
6 ай бұрын
been habving trouble with sealed bearings on these Griemca wheels im doing. this video has helped me man. I am having a issue where when i tighten the wheel down in the forks, the wheel is locking up. cant tell if the bearing or the brake pads are binding but i think i need a better and more proper spacer in the middle of the hub between the 2 bearings like you made in this video. anyways, thanks
@Corn-ped
6 ай бұрын
First tighten it down without the brake plate in there but add some washers to take up the space if it doesn't bind up then the brake plate. if it does bind up then this probably the middle space are not being long enough
@sped49
3 жыл бұрын
Hey thanks for the video, I didn't know they have 29mm bearings. Another well done video, keep em coming.
@Corn-ped
3 жыл бұрын
Thanks!
@kevinlong1959
4 ай бұрын
thanks you sir , that was very helpful to know to make your own spacer*****
@Corn-ped
4 ай бұрын
Awesome! Thanks for watching.
@rezaknoufal1049
Жыл бұрын
Hello msr am fan for youre video
@mopedwithattitude9888
3 жыл бұрын
29mm Bearings!!! RAD! Good vid dude • Honest²
@Corn-ped
3 жыл бұрын
Yeah dude! 29mm! We have been waiting!
@jasonbarresi6651
3 жыл бұрын
I love your videos so Informative. Do you think you’ll ever do one on disk breaks ?
@Corn-ped
3 жыл бұрын
Maybe... I don't have a disc brake bike in the works. I have had a couple and liked em. What exactly would you like to see in a video?
@alexandertroyer
3 жыл бұрын
@@Corn-ped I'd definitely be interested in a disc brake conversion tutorial or series!
@Corn-ped
3 жыл бұрын
@@alexandertroyer Yeah! Ill try to get one done!
@pauloconnor7951
8 ай бұрын
Use thick walled aluminium tube. Weight saving.
@Corn-ped
8 ай бұрын
I need to eat less. Thats the real weight saver.
@xXFR3JL3ROXx
Жыл бұрын
can you tell me please for the rear tires
@Corn-ped
Жыл бұрын
Tell you what about them?
@toatski
Жыл бұрын
How do I get my freewheel gear off, I have tried all types of stuff- help
@Corn-ped
Жыл бұрын
Need a freewheel tool! You can use a 4 prong bmx one if you Grind off two of the prongs.
@christianwilson4739
2 жыл бұрын
Great video. Is this the same for a Puch Maxi snowflake wheel?
@Corn-ped
2 жыл бұрын
Its the same process but the bearings are a different size. Puch snowflake wheels use 16101 bearings. You can get them on Amazon or Treatland.tv
@christianwilson4739
2 жыл бұрын
@@Corn-ped Great, many thanks. The video is really clear. Much appreciated. 😊
@Corn-ped
2 жыл бұрын
Glad it helped!
@floskifilm
8 ай бұрын
Hey, nice video! Do you know where i can get these 29mm bearings? They are mostly sold out when i look online. If not, can i use a 28mm with a shim or do you recommend sticking to loose ball bearings in my case?
@Corn-ped
8 ай бұрын
Treatland sells them. Let them know I sent ya! otherwise yeah a 28mm with shim stock works fine. www.treatland.tv/puch-KUSTOM-special-29mm-sealed-wheel-bearing-p/puch-29mm-kustom-bearing.htm
@floskifilm
8 ай бұрын
@@Corn-ped cheers!👍
@jamespolucha8790
6 ай бұрын
I’m changing 3/4 wheel bearing and axle to 25mm but 25mm bearings are thinner, couldn’t I just make up wheel spacers to fit ?
@Corn-ped
6 ай бұрын
absolutely! Make some spacers or use washers.
@Outback69
8 ай бұрын
Hey bud, I have found every thing else that I need to restore my Puch Maxi. I'm restoring this bike mechanically. Not polishing it to sell or make it a show piece. I just need to make it ready for the road this summer... This is the last mandatory service I need to do before I rebuild my entire engine in 2000 miles. I bought the bike with 2086 on the clock. Now bearing 2200 it's so damn fun. My question is I can go to my local HF Tools to buy all the tools I need to complete the job but where do you buy the metric pipe at or the equivalent for my wheel spacers? I wanna do this right and not screw it all up. I have an electric moped so I don't haft to rush. Also, do you recommend straight cut gears for the E50 at all? I am more focusing on hill climbing and more performance for the future. So if you could get back to me on my pipe question I would appreciate that a lot. Thanks-W.
@Corn-ped
8 ай бұрын
take your 12mm axle to the hardware store and stick it in the plumbing pipes until ya find on that fits. Or go to a metal supply store for a more accurate tube.
@Outback69
8 ай бұрын
@@Corn-ped Thank you
@Outback69
8 ай бұрын
@@Corn-ped Hey, I bought the sealed bearing conversion kit from treatland. My question is. On the brake plate when you slide the brake down on to the drum. On the old shaft there is a nut there and that is used to hold the brake plate down to the drum. That"s with using the 11MM threaded axle. The threaded axle was for the crappy loose bearings. I saved all my hardware to the bike. I''m just trying to figure out how to keep the brake plate secure on the drum with out sliding off. This is my first moped ever. I'm trying to look for the best info I can find and convert it the easiest way possible but make it safe and reliable. As my health goes down hill from here. I don't feel like taking the rims off every season to re pack it. I would rather cut the head off the snake now and end the issues. Thanks for your time and have a good night and a Merry Christmas.
@beng6319
3 жыл бұрын
Does there need to be a washer between the fork legs and the spacer? And does the brake plate need to align with the fork tab to hold it in place?
@Corn-ped
3 жыл бұрын
You do not need a washer on the inside of the fork leg but you should use won between the fork leg in the nuts. You do need to align the brake plate with the fork tabs to hold it in place. I'm using Forks that are too wide for this Hub so I'm going to build an adapter for the disc brake side to fit into the brake slot
@johnseiler9823
3 жыл бұрын
Are there any major changes in the process for the rear drive wheel? The bearings and brakes seem more or less the same
@Corn-ped
3 жыл бұрын
It's the same!
@Mopo502
2 жыл бұрын
oh shiii ... why am I messing with an angle grinder instead of using a pipe cutter. Dumb!! thank you!
@Corn-ped
2 жыл бұрын
Yeah the pipe cutter is great. You. Still gotta do a little clean up, but ita better imo.
@Khapaleno
Жыл бұрын
Hey I just converted my rear wheel to sealed bearings and wonderd what would happen if you didnt use a spacer in between the bearings because a loose ball bearing axle doesnt have a spacer either.
@Corn-ped
Жыл бұрын
You need the spacer in the middle. Otherwise when you tighten the axle it will squeeze the bearings inward and ruin them, and your wheel won't turn smoothly.
@Khapaleno
Жыл бұрын
@@Corn-ped I didnt think of that 😅. Thank you!
@cpm881
Жыл бұрын
Anyone know size of that pipe? I'm guessing it's 1/2 inch inner diameter, which would be about 12.7mm ID ?
@lukeschlitzer5460
Жыл бұрын
I have been wondering the same
@dannywalker9288
4 ай бұрын
What tyres are they, pal?
@Corn-ped
4 ай бұрын
Those are my favorite 17" Vee Rubber tires from treatland.tv www.treatland.tv/vee-rubber-vrm359-moped-tire-17-x-2-5-p/vee-rubber-vrm359-2.5-17.htm
@jonamadatsu2918
3 жыл бұрын
Whose the one salty dude that gave a thumbs down? He probably just put in a Treats order for new loose bearings lol I'm thinking of doing this with my Batavus GoGo. At least for the rear, to see how it goes
@Corn-ped
3 жыл бұрын
Thanks! Yeah I wish they would like me know what they didn't like.
@TwostrokePuchwizard
3 жыл бұрын
What iron pipe size are you using?
@toatski
Жыл бұрын
Looks smaller than 1/2 inch- I’m at the hardware store now- lol
@Corn-ped
Жыл бұрын
I think it was half in and I used a dremel to smooth out an inner seam.
@LizardBikes
2 жыл бұрын
What kind of pipe cutter is that, I don't want a crappy one?
@Corn-ped
2 жыл бұрын
Hey it is a rigid brand from home depot.
@AlexDangerJohnson
3 жыл бұрын
i was gonna say i'm pretty sure hobbit front wheels are the same as puch spoke. can you make a video of you one punching a hotdog?
@Corn-ped
3 жыл бұрын
I'll need a filmer
@AlexDangerJohnson
3 жыл бұрын
@@Corn-ped I'll be in Minneapolis on sunday baybee
@Rolf-nj6nc
3 жыл бұрын
is there a place in the eu where you can buy that bearing ?
@Corn-ped
3 жыл бұрын
I don't think so. Treats will ship it.
@michaelgamba369
3 жыл бұрын
Amazon in Europe has a ton of puch stuff I think you can actually buy the bearing cups if you didnt want to do sealed bearings but Amazon definitely has the 6001r2 sealed bearings
@TheNkuebelbeck
3 жыл бұрын
Anyway to keep old vdo drive?
@Corn-ped
3 жыл бұрын
Yeah totally. Just put a spacer between it and the hub.
@TheNkuebelbeck
3 жыл бұрын
@@Corn-ped so on the snowflakes I did, the race actually had notches for the speedo drive. Race gone, notches gone.
@Corn-ped
3 жыл бұрын
Ahhh yeah. Well then you would have to get creative. You could switch to a spoke hub gear and notch the hub.
Пікірлер: 86