I always wondered how those bits worked, thanks for the explanation
@jonathanr4242
Жыл бұрын
Very nice, concise and easy to understand instruction. Thanks.
@kathleen1060
4 жыл бұрын
Simple and clear. Thanks 😁👍
@lynnquin8565
2 жыл бұрын
Very helpful demonstration!
@CanadianMang
4 жыл бұрын
When you screw two boards together you should drill a clearance hole only in first board! That way you get a much tighter fit between boards.
@sebastjansslavitis3898
4 жыл бұрын
or use partially threaded screw
@Jason_Van_Stone
Жыл бұрын
Dude, it's obviously a test board lmfao
@DiegoSynth
8 ай бұрын
Very good video. Clear, well explained, well showcased. Thanks!
@zulfikranzulmos4066
5 жыл бұрын
I like ur channel very informative and straight to the point.. Not much talking..
@mahmoodkhan6623
2 жыл бұрын
Is countersink bit size 12 mm the right size for a size 8 screw?
@ButterBallTheOpossum
3 жыл бұрын
I like to drill deeper with the countersink until I can put a wooden plug on top of the screw it looks great when done correctly!
@softwaretest1879
6 жыл бұрын
thanks! ´What I am looking to learn for days is, do all of these drill bits go in all of the drills machines? I already have a Bosch drill machine, but the hammer-action one, which works with electricity.I want to buy drill bits for this machine., and I need to know which bits go into it. because its base/rear-end slips/slides into the slot of Drill machine.
@zachthegreat6836
4 жыл бұрын
Software Test yes, they're all machined off of a 1/4 inch hex bit
@prestwichian
6 ай бұрын
Excellent video thank you
@stevep764
4 жыл бұрын
Simples, thankyou.
@saynotospanglish9192
3 жыл бұрын
Thanks. V useful! 👍
@ShopperPlug
3 жыл бұрын
you should mention which countersink bit size is proper for counter sink screw size.
@davidklein4980
5 жыл бұрын
Excellent
@rubypearce8336
4 жыл бұрын
Thx for the help I need it for schol
@zeroa6
6 жыл бұрын
Thanks.
@Claudg2008
Жыл бұрын
To smooth the wood in the conic hole you just made you may run your drill backwards for a few second.
@mahmoodkhan6623
2 жыл бұрын
I want to countersink a screw into sheet metal. Does the countersink bit have to be one that goes through metal? What I'm asking is, do all countersink bits go through metal too?
@AC3dAvE
2 жыл бұрын
Not all bits are made for metal. The wood drill bit may be usable but not recommended. The countersink bit has to be the one to go through metal as they can also easily go through wood.
@mahmoodkhan6623
2 жыл бұрын
@@AC3dAvE hi Dave, is there a specific bit you can recommend from home Depot?
@felixf5211
2 жыл бұрын
@@mahmoodkhan6623 For metal, look for a Weldon zero flute countersink. They're not sold at hardware stores. You can find one at an industrial supply house/site, or on ebay. Good luck.
@ghengis430
Жыл бұрын
Thanks, forgot what to do!
@nashatmoushatak3149
7 жыл бұрын
thanks..
@bshortall1881
5 жыл бұрын
Thanks
@mogbaba
3 жыл бұрын
If I want to have one countersink, what size should I get?
@jimodell3822
3 жыл бұрын
That would depend on the size of the screw head. I would probably use a countersink bit on size over the width of the screw head so that I could sink the screw low enough to use wood putty and completely conceal it.
@extreme748
4 жыл бұрын
this is for v shaped screw head. how about for a flat screw head, what drill bit is used? countersink surely doesnt serve the purpose here
@iFornix
3 жыл бұрын
works the same, the idea is to create a shallow indented hole deep enough for the screw head to be burrowed beneath the surface area - which you would fill to conceal the screw for an aesthetically cleaner look and allow for painting
@docjonesy1968
2 жыл бұрын
You could use a forstner bit to perform your countersink for a flat screw head. You just need to make sure to select an appropriate size bit that fits the screw head to your liking.
@saffronsworld1508
7 жыл бұрын
I am glad I took a wood shop class in high school where I learned what counter-sunk holes are. They allow for a screw's flat top to be recessed below the surface of the wood. That application I heard again later in life when I was in the U.S. Marine Corps. We guys referred to Women Marines as "countersunk Marines." Some of your viewers may not grasp my meaning, but then again, some will get a chuckle.
@andrewford80
7 жыл бұрын
:)
@finnyboy82
3 жыл бұрын
Lmao
@NewbieTuwbie
Жыл бұрын
Couldn't you just screw the first screw deeper to get the same results if not better? I honestly don't understand the purpose of the countersink.
@MrFatboyRuns
Жыл бұрын
Issue with doing that is you risk splitting the wood. I have used the method you described several times and got away with it, but there has been a few times when I bodged it. Much better to use the countersink to guarantee the results.
@mountainman8775
7 ай бұрын
Countersink for neat work, and as previous commenter said so as not to damage the materials.
@jaybushwacker7695
4 жыл бұрын
Some people should not make demonstration videos you are that person
@lindawilliams7519
4 жыл бұрын
He did ok...remember not all you tubers are professionals...just regular ordinary people willing to pass a little something along to others. He did ok.
Пікірлер: 47