Thank you guys for watching! Please consider liking and subscribing. Please be careful when replacing these! if you have any questions please comment below! Belt: amzn.to/31XQPXK Blades: amzn.to/2GdLUKF Spindles(need 2): amzn.to/3uWJLqR Grease Gun: amzn.to/2HSwFaF Socket set: amzn.to/3jKGGDP Wrench set: amzn.to/2TCYqGL
@macmckenzie1242
2 жыл бұрын
You taught me to take it to the shop even though I'll wind up with a flat wallet.
@BreakFixRepair
2 жыл бұрын
lol it’s not that bad!! Just a couple hours and a few tools.
@cindydenesen4050
11 ай бұрын
can you provide a picture of the belt diagram for the lower drive belt- bot surehow to route the bekt thru the pulleys
@BreakFixRepair
11 ай бұрын
The belt that attaches to the deck?
@michelleback4690
2 жыл бұрын
Very helpful video!
@Squad-pl7oo
2 жыл бұрын
Raise your deck hangers all the way up so your deck can slide right out
@baldeagle242
3 жыл бұрын
Thanks for sharing. I just picked one of these up. 👍
@BreakFixRepair
3 жыл бұрын
You’re welcome! Hope it helps!
@12samp
3 жыл бұрын
Holy Moly
@michaelott310
3 жыл бұрын
I was laughing when you were taking the deck off. I have the exact same tractor. Those black brackets catch on everything when you try to slide the deck in or out. I was cussin' up a storm!! But I found it easier to remove the spring and cable when you remove the deck from the right side of the tractor ( where the discharge is). There's more room on that side.
@BreakFixRepair
3 жыл бұрын
LOL!!! That was such a pain!! Definitely the worst part of the whole job!!!!
@halffaucon3736
3 жыл бұрын
I got this too. I use wires to hold those pesky arms up when I slide deck in or out.
@michaelott310
3 жыл бұрын
@@halffaucon3736 I used a bungee cord. LOL
@CeeYa1989
2 жыл бұрын
Dadgum black brackets got me too!!!! 🤨🤯😆
@waynegober3940
3 жыл бұрын
If you have the craftsman t1600 can you give me the spindle part number I can’t find it anywhere online if I’m even looking in the right places
@BreakFixRepair
3 жыл бұрын
Yes! Please check out this link for the spindles for the T1600. I just realized I forgot to add the links to the description so thanks for reminding me! amzn.to/3uWJLqR Hope this helps!
@leedobbyn1602
3 жыл бұрын
Look on the underside of the hood there is a sticker with belt sizes spindles oil filter plug. Sizes and part numbers
@BreakFixRepair
3 жыл бұрын
@@leedobbyn1602 I think mine was off on a few things though. I think they changed part numbers so it was a little harder to find for me.
@badbehavior1883
2 жыл бұрын
MAGNETS...............keeps arms from falling down
@BreakFixRepair
2 жыл бұрын
That’s a great idea!!! Wish I would have known that at the time!!
@annettepeacock1739
Жыл бұрын
You can also just put the rods back into the bottom hole on those brackets and put the cotter pins back in. It keeps the brackets up and the cotter pins from getting lost. Just did this today on the same mower.
Пікірлер: 24