My standard practice to check the clearance by using plastic gauges..more easy and accurate..or u can use soft lead wire
@alwaystruereality3753
2 жыл бұрын
Good Information sir
@engineeringsolutionseee3362
Жыл бұрын
thanks a lot sir 😊
@NazeerAhmed-re9gj
5 жыл бұрын
Thank you bhai my god bless you bhai
@asimmh7956
6 жыл бұрын
Mashalah sunatt puri kar diti eh ustad g
@devendrakumar-pv6gh
5 жыл бұрын
👍 nicely elaborate
@shadhanbasu2862
3 жыл бұрын
Good
@mianabdulrehman9023
Жыл бұрын
السلام علیکم ماشاءاللّٰه
@autoelectrician6023
4 жыл бұрын
ماشاء اللہ. جزاک اللہ
@kurianauto645
5 жыл бұрын
Nice explanation
@vijaybagde2271
2 жыл бұрын
Sir compressor par bi video banao
@salvindersingh6388
2 жыл бұрын
Agar yeh brg. Na touch kare phir aap kiya karegae cap ko reduce karagae yaa or kuch
@nadeemhayat8196
5 жыл бұрын
ALLAH ak ko syht dy. Amin
@cck1496
2 жыл бұрын
Thanks. Would you kindly tell me why crank should touch the bearing (as in the end of the video)? If crank doesn't touch the bearing, what is the issue? Thanks.
@ProEngineering
2 жыл бұрын
Crank should touch the bearing to know the clearance between them. If the crank doesn't touches the bearing on maximum clearance then the clearance is too high
@Deep_Jani
4 жыл бұрын
Sure ,I will use this method & will reply you .
@catr66h
4 жыл бұрын
How tight the crank screws with footbound
@alihaiderhaider1850
5 жыл бұрын
Nadeem bi ap ik video uplod kary jis my 3512 ky injcter hight ķi sating ka share kary
@khanjawaid9459
4 жыл бұрын
Very informative video. Sir please explain why you using paper on bearing.
@ProEngineering
4 жыл бұрын
I used paper to check the clearance and I used it because it is available every where but you should know the thickness of paper you can check the thickness by micrometer
@khanjawaid9459
4 жыл бұрын
@@ProEngineering sir please can you explain other clearance measureing methods?
@bilalikramrajput3967
2 жыл бұрын
kzitem.info/rock/kn-WyxqwgUWQuRPZY40l2w
@afrozalamkhan7609
3 жыл бұрын
Assalam alaykum Nadeem sir yeh btaeen ki kaise pta kreen ki connecting rod Ka cut Kis taraf rakheen
@ProEngineering
3 жыл бұрын
Kis engine ka?
@salvindersingh6388
2 жыл бұрын
Cam ki Tarf
@usmanmechanics2950
6 жыл бұрын
Ya tareeqa ghalt hy chik karny ka.mary hesab sy to
@alihaiderhaider1850
6 жыл бұрын
Ya bilkul galt ho rahi ha chak
@ProEngineering
6 жыл бұрын
I'd love to hear the correct method from you. My number is mentioned in description box. Do contact to tell right method.
Пікірлер: 30